lockup booting 8.0-CURRENT-200811 snap image
Phil Oleson
oz at nixil.net
Mon Nov 17 23:03:44 PST 2008
Hi, I've been trying to update my system to Current to try out the new
usb stack etc..
and have had some problems. Initially I attempted to just do a cvsup,
make buildworld,
make kernel and had problems at the reboot. Ended up having to use the
livecd to swap
out the kernel (loader was strangely hanging before I could type unload;
boot kernel.old)
Anyways, I picked up a new drive to split my system up to have a
working 7 & current.
So, I downloaded the 200811 snap iso's for amd64 & i386 and tried to
boot to them.
Same/similar lockup happens.. now since this board currently doesn't
have a serial port
I've had to handtype what was left on the screen.. so hopefully it's
enough for now.
System: INTEL BLKDG35EC 775 G35 (flashed to the **ECG3510M.86A.0107**
Bios Image)
INTEL C2Q Q9300 2.5G 775
2 gigs memory (messed up on original order and havnt fixed
it yet)
using the built-in Intel video..
so the i386 and the amd64 dvd image I booted with had the same stopping
screen/output
that I could see.. this is what I was able to get down from a verbose boot.
------------------------------------------------------
Initial Probe 0 10 N 0 3 4 5 7 9 10 11 12
Validation 0 10 N 0 3 4 5 7 9 10 11 12
After Disable 0 255 N 0 3 4 5 7 9 10 11 12
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on
acpi0
acpi_hpet0: vend: 0x8086 rev: 0x1 num: 2 hz: 14318180 opts: legacy_route
64-bit Timecounter "HPET" frequency 143181800 Hz quality 900
acpi_button0: <Sleep Button> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pci0: domain=0, physical bus=0
found-> vendor=0x8086, dev=0x2980, revid=0x03
domain=0, bus=0, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x2090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0ns), maxlat=0x00 (0 ns)
found-> vendor=0x8086, dev=0x2982, revid=0x03
domain=0, bus=0, slot=2, func=0
class=03-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0007, statreg=0x0090, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0ns), maxlat=0x00 (0 ns)
intpin=a, irq=11
powerspec 2 supports D0 D3 current D0
MSI supports 1 message
map[10]: type Memory, range32, base 0x90200000, size 20,
enabled
--------------------------------
Any suggestions on how to proceed?
I'll see about installing the new install on the new drive starting at
RELENG_7
and updating to HEAD from there.. so any source changes will have to wait on
completing that.. but anything would help.
-Phil.
More information about the freebsd-current
mailing list