FreeBSD-13.0-CURRENT-arm64-aarch64-ROCKPRO64-20201210-7578a4862f0 broken ?
Søren Schmidt
soren.schmidt at gmail.com
Thu Dec 31 12:49:25 UTC 2020
Hi gang
On my quest on getting the pinebookpro booting again I think I can rule out u-boot for now.
Back on the u-boot-2020.07 where a -current kernel from late July/early august would boot just fine a current kernel fails to talk to the SD card, the only change to an up to date current is not setting the 800Hmz cpll clock and that is known not to make any difference.
Again the same SDcard works just dandy with net/openBSD also I 50Mhz mode. 1 in 10 boots finds the card as 25Mhz and then it “just works”.
Any Ideas ?
U-Boot TPL 2020.07 (Aug 09 2020 - 14:11:44)
Channel 0: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
Channel 1: LPDDR4, 50MHz
BW=32 Col=10 Bk=8 CS0 Row=15 CS1 Row=15 CS=2 Die BW=16 Size=2048MB
256B stride
256B stride
lpddr4_set_rate: change freq to 400000000 mhz 0, 1
lpddr4_set_rate: change freq to 800000000 mhz 1, 0
Trying to boot from BOOTROM
Returning to boot ROM...
U-Boot SPL 2020.07 (Aug 09 2020 - 14:11:44 +0200)
Trying to boot from MMC1
U-Boot 2020.07 (Aug 09 2020 - 14:11:44 +0200)
SoC: Rockchip rk3399
Reset cause: POR
Model: Pine64 Pinebook Pro
DRAM: 3.9 GiB
PMIC: RK808
MMC: mmc at fe310000: 2, mmc at fe320000: 1, sdhci at fe330000: 0
Loading Environment from SPI Flash... SF: Detected gd25q128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
OK
In: serial
Out: vidconsole
Err: vidconsole
Model: Pine64 Pinebook Pro
Net: No ethernet found.
Card did not respond to voltage select!
Hit any key to stop autoboot: 0
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:1...
80449 bytes read in 16 ms (4.8 MiB/s)
Found EFI removable media binary efi/boot/bootaa64.efi
Card did not respond to voltage select!
Scanning disk mmc at fe310000.blk...
Disk mmc at fe310000.blk not ready
Scanning disk mmc at fe320000.blk...
** Unrecognized filesystem type **
Card did not respond to voltage select!
Scanning disk sdhci at fe330000.blk...
Disk sdhci at fe330000.blk not ready
Found 3 disks
BootOrder not defined
EFI boot manager: Cannot load any image
1091484 bytes read in 123 ms (8.5 MiB/s)
Consoles: EFI console
Reading loader env vars from /efi/freebsd/loader.env
Setting currdev to disk0p1:
FreeBSD/arm64 EFI loader, Revision 1.1
(Thu Dec 31 13:17:08 CET 2020 sos at newport.deepcore.dk)
Command line arguments: loader.efi
Image base: 0xf3dfe000
EFI version: 2.80
EFI Firmware: Das U-Boot (rev 8224.1792)
Console: comconsole (0)
Load Path: /efi\boot\bootaa64.efi
Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(0)/HD(1,GPT,319e202c-4b62-11eb-bf03-0800274503a7,0x8000,0x10000)
Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(0)/HD(1,GPT,319e202c-4b62-11eb-bf03-0800274503a7,0x8000,0x10000)
Setting currdev to disk0p1:
Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(1)/SD(0)/HD(2,GPT,319e202c-4b62-11eb-bf03-0800274503a7,0x18000,0x1e7fd8)
Setting currdev to disk0p2:
Loading /boot/defaults/loader.conf
Loading Kernel and Modules (Ctrl-C to Abort)
..................................................
/boot/kernel/kernel text=0x2a8 text=0x512fd8 text=0x1467b4 data=0x138930 data=0x0+0x52e000 syms=[0x8+0xb3730+0x8+0xbdce7]
|
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...
Using DTB provided by EFI at 0x80e9000.
EFI framebuffer information:
addr, size 0xf7800000, 0x3f4800
dimensions 1920 x 1080
stride 1920
masks 0x0000f800, 0x000007e0, 0x0000001f, 0x00000000
---<<BOOT>>---
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2020 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 13.0-CURRENT #6 main-c255441-g4e4e43dc9e1a-dirty: Thu Dec 31 13:16:59 CET 2020
sos at newport.deepcore.dk:/usr/home/sos/FreeBSD/embedded/aarch64-obj/usr/home/sos/FreeBSD/git-current/arm64.aarch64/sys/PINEBOOKPRO arm64
FreeBSD clang version 11.0.0 (git at github.com:llvm/llvm-project.git llvmorg-11.0.0-0-g176249bd673)
VT(efifb): resolution 1920x1080
real memory = 4158349312 (3965 MB)
avail memory = 4033499136 (3846 MB)
Starting CPU 1 (1)
Starting CPU 2 (2)
Starting CPU 3 (3)
FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
arc4random: WARNING: initial seeding bypassed the cryptographic random device because it was not yet seeded and the knob 'bypass_before_seeding' was enabled.
random: entropy device external interface
MAP f3f0f000 mode 2 pages 1
MAP f3f12000 mode 2 pages 2
MAP f6f30000 mode 2 pages 16
WARNING: Device "openfirm" is Giant locked and may be deleted before FreeBSD 13.0.
WARNING: Device "kbd" is Giant locked and may be deleted before FreeBSD 13.0.
kbd0 at kbdmux0
ofwbus0: <Open Firmware Device Tree>
clk_fixed0: <Fixed clock> on ofwbus0
simplebus0: <Flattened device tree simple bus> on ofwbus0
rk_grf0: <RockChip General Register Files> mem 0xff320000-0xff320fff on ofwbus0
rk3399_pmucru0: <Rockchip RK3399 PMU Clock and Reset Unit> mem 0xff750000-0xff750fff on ofwbus0
rk3399_cru0: <Rockchip RK3399 Clock and Reset Unit> mem 0xff760000-0xff760fff on ofwbus0
Cannot set frequency for clk: cpll, error: 22
rk3399_cru0: Failed to set cpll to a frequency of 800000000
rk_grf1: <RockChip General Register Files> mem 0xff770000-0xff77ffff on ofwbus0
regfix0: <Fixed Regulator> on ofwbus0
regfix1: <Fixed Regulator> on ofwbus0
regfix2: <Fixed Regulator> on ofwbus0
regfix3: <Fixed Regulator> on ofwbus0
regfix4: <Fixed Regulator> on ofwbus0
regfix5: <Fixed Regulator> on ofwbus0
regfix6: <Fixed Regulator> on ofwbus0
regfix7: <Fixed Regulator> on ofwbus0
regfix8: <Fixed Regulator> on ofwbus0
regfix9: <Fixed Regulator> on ofwbus0
regfix10: <Fixed Regulator> on ofwbus0
regfix11: <Fixed Regulator> on ofwbus0
simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0xff310000-0xff310fff on ofwbus0
psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
gic0: <ARM Generic Interrupt Controller v3.0> mem 0xfee00000-0xfee0ffff,0xfef00000-0xfefbffff,0xfff00000-0xfff0ffff,0xfff10000-0xfff1ffff,0xfff20000-0xfff2ffff irq 18 on ofwbus0
its0: <ARM GIC Interrupt Translation Service> mem 0xfee20000-0xfee3ffff on gic0
rk_iodomain0: <RockChip IO Voltage Domain> mem 0xff320000-0xff320fff on rk_grf0
rk_iodomain1: <RockChip IO Voltage Domain> mem 0-0xff76ffff,0-0xffff on rk_grf1
rk_pinctrl0: <RockChip Pinctrl controller> on ofwbus0
gpio0: <RockChip GPIO Bank controller> mem 0xff720000-0xff7200ff irq 71 on rk_pinctrl0
gpiobus0: <OFW GPIO bus> on gpio0
gpio1: <RockChip GPIO Bank controller> mem 0xff730000-0xff7300ff irq 72 on rk_pinctrl0
gpiobus1: <OFW GPIO bus> on gpio1
gpio2: <RockChip GPIO Bank controller> mem 0xff780000-0xff7800ff irq 73 on rk_pinctrl0
gpiobus2: <OFW GPIO bus> on gpio2
gpio3: <RockChip GPIO Bank controller> mem 0xff788000-0xff7880ff irq 74 on rk_pinctrl0
gpiobus3: <OFW GPIO bus> on gpio3
gpio4: <RockChip GPIO Bank controller> mem 0xff790000-0xff7900ff irq 75 on rk_pinctrl0
gpiobus4: <OFW GPIO bus> on gpio4
rk_i2c0: <RockChip I2C> mem 0xff110000-0xff110fff irq 20 on ofwbus0
iicbus0: <OFW I2C bus> on rk_i2c0
rk_i2c1: <RockChip I2C> mem 0xff130000-0xff130fff irq 22 on ofwbus0
iicbus1: <OFW I2C bus> on rk_i2c1
rk_i2c2: <RockChip I2C> mem 0xff3c0000-0xff3c0fff irq 38 on ofwbus0
iicbus2: <OFW I2C bus> on rk_i2c2
syr8270: <Silergy SYR827 regulator> at addr 0x80 on iicbus2
rk_i2c3: <RockChip I2C> mem 0xff3d0000-0xff3d0fff irq 39 on ofwbus0
iicbus3: <OFW I2C bus> on rk_i2c3
rk805_pmu0: <RockChip RK805 PMIC> at addr 0x36 irq 76 on iicbus2
generic_timer0: <ARMv8 Generic Timer> irq 2,3,4,5 on ofwbus0
Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000
Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000
rk_tsadc0: <RockChip temperature sensors> mem 0xff260000-0xff2600ff irq 35 on ofwbus0
rk_usb2phy0: <Rockchip RK3399 USB2PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1
rk_usb2phy1: <Rockchip RK3399 USB2PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1
rk_emmcphy0: <Rockchip RK3399 eMMC PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1
rk_pcie_phy0: <Rockchip RK3399 PCIe PHY> mem 0-0xff76ffff,0-0xffff on rk_grf1
rk_typec_phy0: <Rockchip RK3399 PHY TYPEC> mem 0xff7c0000-0xff7fffff on ofwbus0
rk_typec_phy1: <Rockchip RK3399 PHY TYPEC> mem 0xff800000-0xff83ffff on ofwbus0
cpulist0: <Open Firmware CPU Group> on ofwbus0
cpu0: <Open Firmware CPU> on cpulist0
cpufreq_dt0: <Generic cpufreq driver> on cpu0
cpu1: <Open Firmware CPU> on cpulist0
cpufreq_dt1: <Generic cpufreq driver> on cpu1
cpu2: <Open Firmware CPU> on cpulist0
cpufreq_dt2: <Generic cpufreq driver> on cpu2
cpu3: <Open Firmware CPU> on cpulist0
cpufreq_dt3: <Generic cpufreq driver> on cpu3
cpu4: <Open Firmware CPU> on cpulist0
cpufreq_dt4: <Generic cpufreq driver> on cpu4
cpufreq_dt4: Not attaching as cpu is not present
device_attach: cpufreq_dt4 attach returned 6
cpu5: <Open Firmware CPU> on cpulist0
cpufreq_dt5: <Generic cpufreq driver> on cpu5
cpufreq_dt5: Not attaching as cpu is not present
device_attach: cpufreq_dt5 attach returned 6
pmu0: <Performance Monitoring Unit> irq 0 on ofwbus0
pmu1: <Performance Monitoring Unit> irq 1 on ofwbus0
pcib0: <Rockchip PCIe controller> mem 0xf8000000-0xf9ffffff,0xfd000000-0xfdffffff irq 6,7,8 on ofwbus0
pci0: <PCI bus> on pcib0
pcib1: <PCI-PCI bridge> at device 0.0 on pci0
pcib0: failed to reserve resource for pcib1
pcib1: failed to allocate initial memory window: 0-0xfffff
pci1: <PCI bus> on pcib1
nvme0: <Generic NVMe Device> at device 0.0 on pci1
rockchip_dwmmc0: <Synopsys DesignWare Mobile Storage Host Controller (RockChip)> mem 0xfe310000-0xfe313fff irq 10 on ofwbus0
rockchip_dwmmc0: Hardware version ID is 270a
rockchip_dwmmc1: <Synopsys DesignWare Mobile Storage Host Controller (RockChip)> mem 0xfe320000-0xfe323fff irq 11 on ofwbus0
rockchip_dwmmc1: Hardware version ID is 270a
mmc0: <MMC/SD bus> on rockchip_dwmmc1
sdhci_fdt0: <Rockchip RK3399 fdt SDHCI controller> mem 0xfe330000-0xfe33ffff irq 12 on ofwbus0
rk_emmcphy0: got emmcclk clock
sdhci_fdt0-slot0: Hardware doesn't specify timeout clock frequency, setting BROKEN_TIMEOUT quirk.
sdhci_fdt0: 1 slot(s) allocated
mmc1: <MMC/SD bus> on sdhci_fdt0
ehci0: <Generic EHCI Controller> mem 0xfe380000-0xfe39ffff irq 13 on ofwbus0
usbus0: EHCI version 1.0
usbus0 on ehci0
ohci0: <Generic OHCI Controller> mem 0xfe3a0000-0xfe3bffff irq 14 on ofwbus0
usbus1 on ohci0
ehci1: <Generic EHCI Controller> mem 0xfe3c0000-0xfe3dffff irq 15 on ofwbus0
usbus2: EHCI version 1.0
usbus2 on ehci1
ohci1: <Generic OHCI Controller> mem 0xfe3e0000-0xfe3fffff irq 16 on ofwbus0
usbus3 on ohci1
rk_dwc30: <Rockchip RK3399 DWC3> on ofwbus0
xhci0: <Synopsys Designware DWC3> mem 0xfe800000-0xfe8fffff irq 83 on rk_dwc30
xhci0: 64 bytes context size, 32-bit DMA
usbus4: trying to attach
usbus4 on xhci0
rk_dwc31: <Rockchip RK3399 DWC3> on ofwbus0
xhci1: <Synopsys Designware DWC3> mem 0xfe900000-0xfe9fffff irq 84 on rk_dwc31
xhci1: 64 bytes context size, 32-bit DMA
usbus5: trying to attach
usbus5 on xhci1
iicbus0: <unknown card> at addr 0x22
iic0: <I2C generic I/O> on iicbus0
iic1: <I2C generic I/O> on iicbus1
uart0: <16750 or compatible> mem 0xff180000-0xff1800ff irq 26 on ofwbus0
uart1: <16750 or compatible> mem 0xff1a0000-0xff1a00ff irq 28 on ofwbus0
uart1: console (1500000,n,8,1)
spi0: <Rockchip SPI> mem 0xff1d0000-0xff1d0fff irq 31 on ofwbus0
spibus0: <OFW SPI bus> on spi0
mx25l0: <M25Pxx Flash Family> at cs 0 mode 0 on spibus0
mx25l0: device type gd25q128, size 16384K in 256 sectors of 64K, erase size 4K
iicbus2: <unknown card> at addr 0x82
iic2: <I2C generic I/O> on iicbus2
iicbus3: <unknown card> at addr 0x44
iic3: <I2C generic I/O> on iicbus3
pwm0: <Rockchip PWM> mem 0xff420000-0xff42000f on ofwbus0
pwmbus0: <OFW PWM bus> on pwm0
pwmc0: <PWM Control> channel 0 on pwmbus0
pwm1: <Rockchip PWM> mem 0xff420020-0xff42002f on ofwbus0
pwmbus1: <OFW PWM bus> on pwm1
pwmc1: <PWM Control> channel 0 on pwmbus1
gpioc0: <GPIO controller> on gpio0
gpioc1: <GPIO controller> on gpio1
gpioc2: <GPIO controller> on gpio2
gpioc3: <GPIO controller> on gpio3
gpioc4: <GPIO controller> on gpio4
gpioled0: <GPIO LEDs> on ofwbus0
cryptosoft0: <software crypto>
Timecounters tick every 1.000 msec
usbus0: 480Mbps High Speed USB v2.0
usbus1: 12Mbps Full Speed USB v1.0
ugen1.1: <Generic OHCI root HUB> at usbus1
ugen0.1: <Generic EHCI root HUB> at usbus0
uhub0 on usbus0
uhub0: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
uhub1 on usbus1
uhub1: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
usbus2: 480Mbps High Speed USB v2.0
usbus3: 12Mbps Full Speed USB v1.0
ugen2.1: <Generic EHCI root HUB> at usbus2
uhub2 on usbus2
uhub2: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus2
ugen3.1: <Generic OHCI root HUB> at usbus3
uhub3 on usbus3
uhub3: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
usbus4: 5.0Gbps Super Speed USB v3.0
usbus5: 5.0Gbps Super Speed USB v3.0
uhub1: 1 port with 1 removable, self powered
ugen4.1: <Synopsys XHCI root HUB> at usbus4
uhub4 on usbus4
uhub4: <Synopsys XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus4
ugen5.1: <Synopsys XHCI root HUB> at usbus5
uhub5 on usbus5
uhub5: <Synopsys XHCI root HUB, class 9/0, rev 3.00/1.00, addr 1> on usbus5
uhub3: 1 port with 1 removable, self powered
nvd0: <INTEL SSDPEKNW512G8> NVMe namespace
nvd0: 488386MB (1000215216 512 byte sectors)
mmcsd0: 16GB <SDHC SD16G 3.0 SN 01E28E67 MFG 07/2017 by 39 PH> at mmc0 50.0MHz/4bit/2048-block
mmc1: No compatible cards found on bus
Release APs...done
CPU 0: ARM Cortex-A53 r0p4 affinity: 0
Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG>
Trying to mount root from ufs:/dev/mmcsd0p2 [rw,noatime]...
Instruction Set Attributes 0 = <CRC32,SHA2,SHA1,AES+PMULL>
Instruction Set Attributes 1 = <>
Processor Features 0 = <GIC,AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32>
Processor Features 1 = <>
Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA>
Memory Model Features 1 = <8bit VMID>
Memory Model Features 2 = <32bit CCIDX,48bit VA>
Debug Features 0 = <2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3,Debugv8>
Debug Features 1 = <>
Auxiliary Features 0 = <>
Auxiliary Features 1 = <>
CPU 1: ARM Cortex-A53 r0p4 affinity: 1
CPU 2: ARM Cortex-A53 r0p4 affinity: 2
CPU 3: ARM Cortex-A53 r0p4 affinity: 3
Unresolved linked clock found: clkin_gmac
uhub4: 2 ports with 2 removable, self powered
uhub0: 1 port with 1 removable, self powered
mmc0: CMD7 failed, RESULT: 1
mmc0: Card at relative address 7 failed to select
mmcsd0: Error indicated: 1 Timeout
Fatal data abort:
x0: ffffa00000cf9b00
x1: ffff000063dc9000
x2: 40
x3: ffff000040de1100
x4: ffff00005a1abaa0
x5: ffff00005a1ab7a0
x6: 0
x7: 6a0
x8: 0
x9: ffff0000006d2df0
x10: 2
x11: 0
x12: 1
x13: 2af8
x14: 43f
x15: 2
x16: ffffffff
x17: 3
x18: ffff00005a1ab860
x19: ffffa00000cf7c00
x20: 80
x21: ffff0000006f1000
x22: ffff0000006f1000
x23: ffff000064b43788
x24: 0
x25: ffffa00000cf5b80
x26: ffffa00000c2a3b4
x27: ffffa00000cf9e00
x28: ffffa00000cf5b80
x29: ffff00005a1ab860
sp: ffff00005a1ab860
lr: ffff0000004edfe8
elr: ffff0000004ee048
spsr: 145
far: 18
esr: 96000004
panic: vm_fault failed: ffff0000004ee048
cpuid = 3
time = 2
KDB: stack backtrace:
db_trace_self() at db_trace_self_wrapper+0x30
pc = 0xffff0000004c79f0 lr = 0xffff00000002f360
sp = 0xffff00005a1ab280 fp = 0xffff00005a1ab480
db_trace_self_wrapper() at vpanic+0x194
pc = 0xffff00000002f360 lr = 0xffff0000002185a0
sp = 0xffff00005a1ab490 fp = 0xffff00005a1ab4f0
vpanic() at panic+0x44
pc = 0xffff0000002185a0 lr = 0xffff000000218408
sp = 0xffff00005a1ab500 fp = 0xffff00005a1ab5b0
panic() at data_abort+0x1d8
pc = 0xffff000000218408 lr = 0xffff0000004e89e0
sp = 0xffff00005a1ab5c0 fp = 0xffff00005a1ab630
data_abort() at do_el1h_sync+0x144
pc = 0xffff0000004e89e0 lr = 0xffff0000004e7acc
sp = 0xffff00005a1ab640 fp = 0xffff00005a1ab680
do_el1h_sync() at handle_el1h_sync+0x78
pc = 0xffff0000004e7acc lr = 0xffff0000004ca078
sp = 0xffff00005a1ab690 fp = 0xffff00005a1ab7d0
handle_el1h_sync() at dwmmc_intr+0x94
pc = 0xffff0000004ca078 lr = 0xffff0000004edfe4
sp = 0xffff00005a1ab7e0 fp = 0xffff00005a1ab860
dwmmc_intr() at ithread_loop+0x418
pc = 0xffff0000004edfe4 lr = 0xffff0000001d67e8
sp = 0xffff00005a1ab870 fp = 0xffff00005a1ab8f0
ithread_loop() at fork_exit+0x90
pc = 0xffff0000001d67e8 lr = 0xffff0000001d1ecc
sp = 0xffff00005a1ab900 fp = 0xffff00005a1ab950
fork_exit() at fork_trampoline+0x10
pc = 0xffff0000001d1ecc lr = 0xffff0000004e7818
sp = 0xffff00005a1ab960 fp = 0x0000000000000000
KDB: enter: panic
[ thread pid 11 tid 100043 ]
Stopped at dwmmc_intr+0xf8: ldr w8, [x8, #24]
db>
--
Søren Schmidt
sos at deepcore.dk <mailto:sos at deepcore.dk> / sos at freebsd.org <mailto:sos at freebsd.org>
"So much code to hack, so little time”
More information about the freebsd-arm
mailing list