How to boot freebsd on rpi4b?

Tue Dec 17 16:18:29 UTC 2019

Does this garbling happen just after /sbin/init runs?

You need to add an overlay to your config.txt, I can’t remember which one from here. Or double your comspeed from that point.

On Tue, Dec 17, 2019 at 13:40, ykla <yklaxds at gmail.com> wrote:

> I try two tools putty and xshell. Com10 115200.
>
> ykla <yklaxds at gmail.com> 于 2019年12月17日周二 上午11:47写道：
>
>> PL2303 TTL to USB can only output and I can't input anything. Any input
>> are garbled.
>>
>> [image: 1217114605.png]
>>
>> ykla <yklaxds at gmail.com> 于2019年12月17日周二 上午11:13写道：
>>
>>> I reboot for 10 times and now show me root login, but usually stops on
>>> lo0.
>>> Here's log:
>>>
>>> Connecting to COM10...
>>> Connected.
>>>
>>> MMC: emmc2 at 7e340000: 0, mmc at 7e300000: 1
>>> Loading Environment from FAT... In: serial
>>> Out: vidconsole
>>> Err: vidconsole
>>> Net: Net Initialization Skipped
>>> No ethernet found.
>>> Hit any key to stop autoboot: 0
>>> switch to partitions #0, OK
>>> mmc0 is current device
>>> Scanning mmc 0:1...
>>> Found EFI removable media binary efi/boot/bootaa64.efi
>>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
>>> Scanning disk emmc2 at 7e340000.blk...
>>> Scanning disk mmc at 7e300000.blk...
>>> Disk mmc at 7e300000.blk not ready
>>> Found 3 disks
>>> BootOrder not defined
>>> EFI boot manager: Cannot load any image
>>> 677944 bytes read in 77 ms (8.4 MiB/s)
>>> libfdt fdt_check_header(): FDT_ERR_BADMAGIC
>>> Consoles: EFI console
>>> Reading loader env vars from /efi/freebsd/loader.env
>>> Setting currdev to disk0p1:
>>> FreeBSD/arm64 EFI loader, Revision 1.1
>>> (Thu Dec 12 06:37:06 UTC 2019 root at releng1.nyi.freebsd.org)
>>>
>>> Command line arguments: loader.efi
>>> Image base: 0x39ea3000
>>> EFI version: 2.80
>>> EFI Firmware: Das U-Boot (rev 8217.4096)
>>> Console: efi (0x1000)
>>> Load Path: /efi\boot\bootaa64.efi
>>> Load Device:
>>> /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(0)/SD(0)/HD(1,MBR,0xf6fc52af,0x81f,0x18fa8)
>>> Trying ESP:
>>> /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(0)/SD(0)/HD(1,MBR,0xf6fc52af,0x81f,0x18fa8)
>>> Setting currdev to disk0p1:
>>> Trying:
>>> /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/SD(0)/SD(0)/HD(2,MBR,0xf6fc52af,0x197c7,0xeb68839)
>>> Setting currdev to disk0p2:
>>> Loading /boot/defaults/loader.conf
>>> Loading /boot/device.hints
>>> Loading /boot/loader.conf
>>> Loading /boot/loader.conf.local
>>> Loading kernel...
>>> /boot/kernel/kernel text=0x9785cc data=0x18f538 data=0x0+0x79b9e0
>>> syms=[0x8+0x1441e0+0x8+0x12ebce]
>>> Loading configured modules...
>>> /boot/kernel/umodem.ko text=0x2100 text=0x13a0 data=0x6e0+0x10
>>> syms=[0x8+0xf48+0x8+0xb6e]
>>> /boot/entropy size=0x1000
>>>
>>> Hit [Enter] to boot immediately, or any other key for command prompt.
>>> Booting [/boot/kernel/kernel]...
>>> Using DTB provided by EFI at 0x7ef2000.
>>> EFI framebuffer information:
>>> addr, size 0x3eab2000, 0x148000
>>> dimensions 656 x 512
>>> stride 656
>>> masks 0x00ff0000, 0x0000ff00, 0x000000ff, 0xff000000
>>> ---<<BOOT>>---
>>> KDB: debugger backends: ddb
>>> KDB: current backend: ddb
>>> Copyright (c) 1992-2019 The FreeBSD Project.
>>> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
>>> The Regents of the University of California. All rights reserved.
>>> FreeBSD is a registered trademark of The FreeBSD Foundation.
>>> FreeBSD 13.0-CURRENT #0 r355634: Thu Dec 12 07:51:26 UTC 2019
>>> root at releng1.nyi.freebsd.org:/usr/obj/usr/src/arm64.aarch64/sys/GENERIC
>>> arm64
>>> FreeBSD clang version 9.0.0 (tags/RELEASE_900/final 372316) (based on
>>> LLVM 9.0.0)
>>> WARNING: WITNESS option enabled, expect reduced performance.
>>> VT(efifb): resolution 656x512
>>> module firmware already present!
>>> KLD file umodem.ko is missing dependencies
>>> Starting CPU 1 (1)
>>> Starting CPU 2 (2)
>>> Starting CPU 3 (3)
>>> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs
>>> random: unblocking device.
>>> random: entropy device external interface
>>> MAP 39f53000 mode 2 pages 1
>>> MAP 39f57000 mode 2 pages 1
>>> MAP 3b360000 mode 2 pages 16
>>> MAP fe100000 mode 0 pages 1
>>> WARNING: Device "kbd" is Giant locked and may be deleted before FreeBSD
>>> 13.0.
>>> kbd0 at kbdmux0
>>> WARNING: Device "openfirm" is Giant locked and may be deleted before
>>> FreeBSD 13.0.
>>> ofwbus0: <Open Firmware Device Tree>
>>> simplebus0: <Flattened device tree simple bus> on ofwbus0
>>> ofw_clkbus0: <OFW clocks bus> on ofwbus0
>>> clk_fixed0: <Fixed clock> on ofw_clkbus0
>>> clk_fixed1: <Fixed clock> on ofw_clkbus0
>>> simplebus1: <Flattened device tree simple bus> on ofwbus0
>>> simplebus2: <Flattened device tree simple bus> on ofwbus0
>>> regfix0: <Fixed Regulator> on ofwbus0
>>> regfix1: <Fixed Regulator> on ofwbus0
>>> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0
>>> gic0: <ARM Generic Interrupt Controller> mem
>>> 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff
>>> irq 46 on simplebus0
>>> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256
>>> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 22,23
>>> on simplebus0
>>> gpiobus0: <OFW GPIO bus> on gpio0
>>> gpioregulator0: <GPIO controlled regulator> on ofwbus0
>>> gpioregulator0: cannot get pin 0
>>> gpioregulator0: cannot parse parameters
>>> device_attach: gpioregulator0 attach returned 6
>>> generic_timer0: <ARMv7 Generic Timer> irq 4,5,6,7 on ofwbus0
>>> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000
>>> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000
>>> gpioregulator0: <GPIO controlled regulator> on ofwbus0
>>> gpioregulator0: cannot get pin 0
>>> gpioregulator0: cannot parse parameters
>>> device_attach: gpioregulator0 attach returned 6
>>> gpioregulator0: <GPIO controlled regulator> on ofwbus0
>>> gpioregulator0: cannot get pin 0
>>> gpioregulator0: cannot parse parameters
>>> device_attach: gpioregulator0 attach returned 6
>>> gpioregulator0: <GPIO controlled regulator> on ofwbus0
>>> gpioregulator0: cannot get pin 0
>>> gpioregulator0: cannot parse parameters
>>> device_attach: gpioregulator0 attach returned 6
>>> gpioregulator0: <GPIO controlled regulator> on ofwbus0
>>> gpioregulator0: cannot get pin 0
>>> gpioregulator0: cannot parse parameters
>>> device_attach: gpioregulator0 attach returned 6
>>> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0
>>> gpioregulator0: <GPIO controlled regulator> on ofwbus0
>>> gpioregulator0: cannot get pin 0
>>> gpioregulator0: cannot parse parameters
>>> device_attach: gpioregulator0 attach returned 6
>>> bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007aff irq
>>> 9,10,11,12,13,14,15,16,17,18,19 on simplebus0
>>> Checking root against brcm,bcm2837
>>> Checking root against brcm,bcm2711
>>> bcmwd0: <BCM2708/2835 Watchdog> mem
>>> 0x7e100000-0x7e100113,0x7e00a000-0x7e00a023,0x7ec11000-0x7ec1101f on
>>> simplebus0
>>> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 21 on
>>> simplebus0
>>> gpioc0: <GPIO controller> on gpio0
>>> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 24 on
>>> simplebus0
>>> uart0: console (115200,n,8,1)
>>> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e340000-0x7e3400ff
>>> irq 60 on simplebus0
>>> mmc0: <MMC/SD bus> on sdhci_bcm0
>>> sdhci_bcm1: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff
>>> irq 61 on simplebus0
>>> mmc1: <MMC/SD bus> on sdhci_bcm1
>>> fb0: <BCM2835 VT framebuffer driver> on simplebus0
>>> fb0: keeping existing fb bpp of 32
>>> fbd0 on fb0
>>> WARNING: Device "fb" is Giant locked and may be deleted before FreeBSD
>>> 13.0.
>>> VT: Replacing driver "efifb" with new "fb".
>>> fb0: 656x512(656x512 at 0,0) 32bpp
>>> fb0: fbswap: 1, pitch 2624, base 0x3eab2000, screen_size 1343488
>>> cpulist0: <Open Firmware CPU Group> on ofwbus0
>>> cpu0: <Open Firmware CPU> on cpulist0
>>> cpu1: <Open Firmware CPU> on cpulist0
>>> cpu2: <Open Firmware CPU> on cpulist0
>>> cpu3: <Open Firmware CPU> on cpulist0
>>> gpioled0: <GPIO LEDs> on ofwbus0
>>> gpioled0: <led1> failed to map pin
>>> gpioregulator0: <GPIO controlled regulator> on ofwbus0
>>> gpioregulator0: cannot get pin 0
>>> gpioregulator0: cannot parse parameters
>>> device_attach: gpioregulator0 attach returned 6
>>> cryptosoft0: <software crypto>
>>> Timecounters tick every 1.000 msec
>>> usb_needs_explore_all: no devclass
>>> mmcsd0: 126GB <SDHC AcMKS 0.2 SN 40400CB7 MFG 06/2019 by 156 SO> at mmc0
>>> 50.0MHz/4bit/65535-block
>>> sdhci_bcm1-slot0: Got command interrupt 0x00030000, but there is no
>>> active command.
>>> sdhci_bcm1-slot0: ============== REGISTER DUMP ==============
>>> sdhci_bcm1-slot0: Sys addr: 0x00000000 | Version: 0x00009902
>>> sdhci_bcm1-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
>>> sdhci_bcm1-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
>>> sdhci_bcm1-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
>>> sdhci_bcm1-slot0: Power: 0x0000000f | Blk gap: 0x00000000
>>> sdhci_bcm1-slot0: Wake-up: 0x00000000 | Clock: 0x0000fa07
>>> sdhci_bcm1-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
>>> sdhci_bcm1-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
>>> sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
>>> sdhci_bcm1-slot0: Caps: 0x00000000 | Caps2: 0x00000000
>>> sdhci_bcm1-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
>>> sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
>>> sdhci_bcm1-slot0: ===========================================
>>> sdhci_bcm1-slot0: Got command interrupt 0x00030000, but there is no
>>> active command.
>>> sdhci_bcm1-slot0: ============== REGISTER DUMP ==============
>>> sdhci_bcm1-slot0: Sys addr: 0x00000000 | Version: 0x00009902
>>> sdhci_bcm1-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
>>> sdhci_bcm1-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
>>> sdhci_bcm1-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
>>> sdhci_bcm1-slot0: Power: 0x0000000f | Blk gap: 0x00000000
>>> sdhci_bcm1-slot0: Wake-up: 0x00000000 | Clock: 0x0000fa07
>>> sdhci_bcm1-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
>>> sdhci_bcm1-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
>>> sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
>>> sdhci_bcm1-slot0: Caps: 0x00000000 | Caps2: 0x00000000
>>> sdhci_bcm1-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
>>> sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
>>> sdhci_bcm1-slot0: ===========================================
>>> sdhci_bcm1-slot0: Got command interrupt 0x00030000, but there is no
>>> active command.
>>> sdhci_bcm1-slot0: ============== REGISTER DUMP ==============
>>> sdhci_bcm1-slot0: Sys addr: 0x00000000 | Version: 0x00009902
>>> sdhci_bcm1-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
>>> sdhci_bcm1-slot0: Argument: 0x000001aa | Trn mode: 0x00000000
>>> sdhci_bcm1-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
>>> sdhci_bcm1-slot0: Power: 0x0000000f | Blk gap: 0x00000000
>>> sdhci_bcm1-slot0: Wake-up: 0x00000000 | Clock: 0x0000fa07
>>> sdhci_bcm1-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
>>> sdhci_bcm1-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
>>> sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
>>> sdhci_bcm1-slot0: Caps: 0x00000000 | Caps2: 0x00000000
>>> sdhci_bcm1-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
>>> sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
>>> sdhci_bcm1-slot0: ===========================================
>>> sdhci_bcm1-slot0: Got command interrupt 0x00030000, but there is no
>>> active command.
>>> sdhci_bcm1-slot0: ============== REGISTER DUMP ==============
>>> sdhci_bcm1-slot0: Sys addr: 0x00000000 | Version: 0x00009902
>>> sdhci_bcm1-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
>>> sdhci_bcm1-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
>>> sdhci_bcm1-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
>>> sdhci_bcm1-slot0: Power: 0x0000000f | Blk gap: 0x00000000
>>> sdhci_bcm1-slot0: Wake-up: 0x00000000 | Clock: 0x0000fa07
>>> sdhci_bcm1-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
>>> sdhci_bcm1-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
>>> sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
>>> sdhci_bcm1-slot0: Caps: 0x00000000 | Caps2: 0x00000000
>>> sdhci_bcm1-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
>>> sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
>>> sdhci_bcm1-slot0: ===========================================
>>> sdhci_bcm1-slot0: Got command interrupt 0x00030000, but there is no
>>> active command.
>>> sdhci_bcm1-slot0: ============== REGISTER DUMP ==============
>>> sdhci_bcm1-slot0: Sys addr: 0x00000000 | Version: 0x00009902
>>> sdhci_bcm1-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
>>> sdhci_bcm1-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
>>> sdhci_bcm1-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
>>> sdhci_bcm1-slot0: Power: 0x0000000f | Blk gap: 0x00000000
>>> sdhci_bcm1-slot0: Wake-up: 0x00000000 | Clock: 0x0000fa07
>>> sdhci_bcm1-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
>>> sdhci_bcm1-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
>>> sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
>>> sdhci_bcm1-slot0: Caps: 0x00000000 | Caps2: 0x00000000
>>> sdhci_bcm1-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
>>> sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
>>> sdhci_bcm1-slot0: ===========================================
>>> sdhci_bcm1-slot0: Got command interrupt 0x00030000, but there is no
>>> active command.
>>> sdhci_bcm1-slot0: ============== REGISTER DUMP ==============
>>> sdhci_bcm1-slot0: Sys addr: 0x00000000 | Version: 0x00009902
>>> sdhci_bcm1-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
>>> sdhci_bcm1-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
>>> sdhci_bcm1-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
>>> sdhci_bcm1-slot0: Power: 0x0000000f | Blk gap: 0x00000000
>>> sdhci_bcm1-slot0: Wake-up: 0x00000000 | Clock: 0x0000fa07
>>> sdhci_bcm1-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
>>> sdhci_bcm1-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
>>> sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
>>> sdhci_bcm1-slot0: Caps: 0x00000000 | Caps2: 0x00000000
>>> sdhci_bcm1-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
>>> sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
>>> sdhci_bcm1-slot0: ===========================================
>>> sdhci_bcm1-slot0: Got command interrupt 0x00030000, but there is no
>>> active command.
>>> sdhci_bcm1-slot0: ============== REGISTER DUMP ==============
>>> sdhci_bcm1-slot0: Sys addr: 0x00000000 | Version: 0x00009902
>>> sdhci_bcm1-slot0: Blk size: 0x00000000 | Blk cnt: 0x00000000
>>> sdhci_bcm1-slot0: Argument: 0x00000000 | Trn mode: 0x00000000
>>> sdhci_bcm1-slot0: Present: 0x000f0000 | Host ctl: 0x00000001
>>> sdhci_bcm1-slot0: Power: 0x0000000f | Blk gap: 0x00000000
>>> sdhci_bcm1-slot0: Wake-up: 0x00000000 | Clock: 0x0000fa07
>>> sdhci_bcm1-slot0: Timeout: 0x00000000 | Int stat: 0x00000000
>>> sdhci_bcm1-slot0: Int enab: 0x01ff00bb | Sig enab: 0x01ff00bb
>>> sdhci_bcm1-slot0: AC12 err: 0x00000000 | Host ctl2:0x00000000
>>> sdhci_bcm1-slot0: Caps: 0x00000000 | Caps2: 0x00000000
>>> sdhci_bcm1-slot0: Max curr: 0x00000001 | ADMA err: 0x00000000
>>> sdhci_bcm1-slot0: ADMA addr:0x00000000 | Slot int: 0x00000000
>>> sdhci_bcm1-slot0: ===========================================
>>> mmc1: No compatible cards found on bus
>>> Release APs...done
>>> CPU 0: ARM Cortex-A72 r0p3 affinity: 0
>>> Instruction Set Attributes 0 = <CRC32>
>>> Trying to mount root from ufs:/dev/ufs/rootfs [rw]...
>>> Instruction Set Attributes 1 = <>
>>> Processor Features 0 = <AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32>
>>> Processor Features 1 = <>
>>> Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit
>>> ASID,16TB PA>
>>> Memory Model Features 1 = <8bit VMID>
>>> Memory Model Features 2 = <32bit CCIDX,48bit VA>
>>> Debug Features 0 = <2 CTX BKPTs,4 Watchpoints,6
>>> Breakpoints,PMUv3,Debugv8>
>>> Debug Features 1 = <>
>>> Auxiliary Features 0 = <>
>>> Auxiliary Features 1 = <>
>>> CPU 1: ARM Cortex-A72 r0p3 affinity: 1
>>> CPU 2: ARM Cortex-A72 r0p3 affinity: 2
>>> CPU 3: ARM Cortex-A72 r0p3 affinity: 3
>>> WARNING: WITNESS option enabled, expect reduced performance.
>>> WARNING: was not properly dismounted
>>> Warning: no time-of-day clock registered, system time will not be set
>>> accurately
>>> Setting hostuuid: 30303031-3030-3030-3165-653364373161.
>>> Setting hostid: 0x3c744718.
>>> No suitable dump device was found.
>>> Starting file system checks:
>>> /dev/ufs/rootfs: INCORRECT BLOCK COUNT I=4470 (8 should be 0) (CORRECTED)
>>> /dev/ufs/rootfs: LINK COUNT DIR I=11 OWNER=root MODE=40755
>>> /dev/ufs/rootfs: SIZE=512 MTIME=Dec 12 09:12 2019 COUNT 25 SHOULD BE 24
>>> (ADJUSTED)
>>> /dev/ufs/rootfs: UNREF FILE I=4466 OWNER=root MODE=100644
>>> /dev/ufs/rootfs: SIZE=0 MTIME=Dec 12 09:12 2019
>>> (CLEARED)
>>> /dev/ufs/rootfs: UNREF FILE I=4469 OWNER=root MODE=100644
>>> /dev/ufs/rootfs: SIZE=0 MTIME=Dec 12 09:12 2019
>>> (CLEARED)
>>> /dev/ufs/rootfs: UNREF FILE I=4470 OWNER=root MODE=100444
>>> /dev/ufs/rootfs: SIZE=0 MTIME=Dec 12 09:12 2019
>>> (CLEARED)
>>> /dev/ufs/rootfs: UNREF FILE I=4501 OWNER=root MODE=100600
>>> /dev/ufs/rootfs: SIZE=4096 MTIME=Dec 12 09:11 2019
>>> (CLEARED)
>>> /dev/ufs/rootfs: SUMMARY INFORMATION BAD (SALVAGED)
>>> /dev/ufs/rootfs: BLK(S) MISSING IN BIT MAPS (SALVAGED)
>>> /dev/ufs/rootfs: 23639 files, 705985 used, 29178238 free (302 frags,
>>> 3647242 blocks, 0.0% fragmentation)
>>> Mounting local filesystems:.
>>> ELF ldconfig path: /lib /usr/lib /usr/lib/compat
>>> Setting hostname: generic.
>>> Setting up harvesting:
>>> [UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,[NET_ETHER],NET_TUN,MOUSE,KEYBOARD,ATTACH,CACHED
>>> Feeding entropy: .
>>> lo0: link state changed to UP
>>> Starting Network: lo0.
>>> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384
>>> options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6>
>>> inet6 ::1 prefixlen 128
>>> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1
>>> inet 127.0.0.1 netmask 0xff000000
>>> groups: lo
>>> nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL>
>>> Starting devd.
>>> add host 127.0.0.1: gateway lo0 fib 0: route already in table
>>> add host ::1: gateway lo0 fib 0: route already in table
>>> add net fe80::: gateway ::1
>>> add net ff02::: gateway ::1
>>> add net ::ffff:0.0.0.0: gateway ::1
>>> add net ::0.0.0.0: gateway ::1
>>> Creating and/or trimming log files.
>>> Starting syslogd.
>>> Clearing /tmp (X related).
>>> Updating motd:.
>>> Mounting late filesystems:.
>>> Updating /var/run/os-release done.
>>> Configuring vt: blanktime.
>>> Performing sanity check on sshd configuration.
>>> Starting sshd.
>>> Starting cron.
>>> Starting background file system checks in 60 seconds.
>>>
>>> Thu Dec 12 09:13:14 UTC 2019
>>>
>>> FreeBSD/arm64 (generic) (ttyu0)
>>>
>>> login:
>>>
>>> Kyle Evans <kevans at freebsd.org> 于2019年12月17日周二 上午10:33写道：
>>>
>>>> On Mon, Dec 16, 2019 at 8:30 PM ykla <yklaxds at gmail.com> wrote:
>>>> > ykla <yklaxds at gmail.com> 于 2019年12月17日周二 上午10:27写道：
>>>> >> Kyle Evans <kevans at freebsd.org> 于 2019年12月17日周二 上午10:04写道：
>>>> >>>
>>>> >>> On Mon, Dec 16, 2019 at 7:50 PM ykla <yklaxds at gmail.com> wrote:
>>>> >>> >
>>>> >>> > Hi, I download latest version 12.12 current 13 img and write in TF
>>>> card.
>>>> >>> > Then I download rpi-firmware(2019-12-05 16:15:16) and extract and
>>>> copy it
>>>> >>> > in BOOT partition. And look at my screen shows me that stop boot
>>>> on lo0
>>>> >>> > state. I know it can't support USB/PCI/ethernet and I just want to
>>>> install
>>>> >>> > it. Thanks.
>>>> >>>
>>>> >>> That's a most curious failure mode... if you got to the point where
>>>> >>> we're bringing up lo0, it should have either been fine or blown up
>>>> >>> terribly in an obvious way -- I'll reimage tomorrow-ish based on the
>>>> >>> latest snapshot and see if I can reproduce.
>>>> >>>
>>>> >>> In the meantime, can you post a transcript of the boot?
>>>> >>>
>>>> >>> Thanks,
>>>> >>>
>>>> >>> Kyle Evans
>>>> >>
>>>> >> New error: stopped at
>>>> >> Warning: no time-of-day clock registered. system time will not be set
>>>> accurately.
>>>> >
>>>> > I just reboot and bugs show:
>>>> > lo0 :link state change to UP.
>>>> >
>>>>
>>>> Can you scroll up to just above that sdhci output and take another
>>>> picture? (above the =============)
>>>>
>>>> Thanks,
>>>>
>>>> Kyle Evans
>>>>
>>>
> _______________________________________________
> freebsd-arm at freebsd.org mailing list
> https://lists.freebsd.org/mailman/listinfo/freebsd-arm
> To unsubscribe, send any mail to "freebsd-arm-unsubscribe at freebsd.org"