ubldr.bin on sheevaplug (11-STABLE)

[Ronald Klop]

Hello,

I just build a new 11-STABLE for my Sheevaplug. (BTW, it feels a lot more  
stable the last two or three months. I can still create UFS corruption on  
my usb-stick, but it does not crash that often anymore.)

Back to the subject. I just tried ubldr.bin again. Previous attempts gave  
no output and just hang. But now I get an error.

This  is what I did:
----------------------------------------------------------- START
# 09:40:06 root at sheeva2 [/boot]
nandtool erase dev=/dev/gnand0s.fbsd-boot

# 09:40:15 root at sheeva2 [/boot]
dd if=ubldr.bin of=/dev/gnand0s.fbsd-boot bs=2k conv=sync
120+1 records in
121+0 records out
247808 bytes transferred in 0.251712 secs (984489 bytes/sec)

# 09:40:43 root at sheeva2 [/boot]
shutdown -r now
<... snip ...>
Rebooting...
þ
          __  __                      _ _
         |  \/  | __ _ _ ____   _____| | |
         | |\/| |/ _` | '__\ \ / / _ \ | |
         | |  | | (_| | |   \ V /  __/ | |
         |_|  |_|\__,_|_|    \_/ \___|_|_|
  _   _     ____              _
| | | |   | __ )  ___   ___ | |_
| | | |___|  _ \ / _ \ / _ \| __|
| |_| |___| |_) | (_) | (_) | |_
  \___/    |____/ \___/ \___/ \__|
  ** MARVELL BOARD: SHEEVA PLUG LE

U-Boot 1.1.4 (Jul 19 2009 - 16:03:28) Marvell version: 3.4.19

U-Boot code: 00600000 -> 0067FFF0  BSS: -> 006CFB00

Soc: 88F6281 A0 (DDR2)
CPU running @ 1200Mhz L2 running @ 400Mhz
SysClock = 400Mhz , TClock = 200Mhz

DRAM CAS Latency = 5 tRP = 5 tRAS = 18 tRCD=6
DRAM CS[0] base 0x00000000   size 256MB
DRAM CS[1] base 0x10000000   size 256MB
DRAM Total size 512MB  16bit width
Addresses 8M - 0M are saved for the U-Boot usage.
Mem malloc Initialization (8M - 7M): Done
NAND:512 MB
Flash:  0 kB

CPU : Marvell Feroceon (Rev 1)

Streaming disabled
Write allocate disabled


USB 0: host mode
PEX 0: interface detected no Link.
Net:   egiga0 [PRIME], egiga1
Hit any key to stop autoboot:  0

NAND read: device 0 offset 0x200000, size 0x600000
  6291456 bytes read: OK
## Starting application at 0x00900000 ...
data abort
pc : [<0092a0c0>]	   lr : [<00919fe4>]
sp : 005fe43c  ip : 0093a950	 fp : 005fe454
r10: 00000000  r9 : 0093de48	 r8 : 00938ce8
r7 : 01badab1  r6 : 00938ceb	 r5 : 00938ce8  r4 : 00000000
r3 : 00000000  r2 : 00938ce8	 r1 : 00000001  r0 : 0093bfb8
Flags: Nzcv  IRQs off  FIQs off  Mode SVC_32
Resetting CPU ...

----------------------------------------------------------- END

The commands are the same as when I install kernel.bin. I only substituted  
the if= value of dd with ubldr.bin.

Any ideas?
Can I provide more information?

Regards,
Ronald.