Built world on RPI-B, ports pending
Peter Cornelius
pcc at gmx.net
Wed Nov 6 23:29:33 UTC 2013
To whom it may concern,
I just want to give some feedback on the Raspberry Pi in that I just
completed a kernel and world build and install (both over NFS and using
the current RPI-B config file) successfully this morning (or rather,
last night ;-)), and just rebooted into that kernel world more or less
happily. The version I started with was
FreeBSD raspberry-pi 11.0-CURRENT FreeBSD 11.0-CURRENT #0 r257540: Sat
Nov 2 11:14:36 CET 2013
root at petra:/usr/obj/RaspberryPI/arm.armv6/usr/SVN/FreeBSD/base/head/sys
/RPI-B arm
(which, in turn, I built on FreeBSD petra.cornelius 9.2-STABLE FreeBSD
9.2-STABLE #7 r256090: Sun Oct 6 23:14:25 CEST 2013
root at petra:/usr/obj/usr/SVN/FreeBSD/base/stable/9/sys/PETRA amd64,
installed on a mem card and booted the RPI from).
uname at the RPI now reports
FreeBSD raspberry-pi 11.0-CURRENT FreeBSD 11.0-CURRENT #0: Tue Nov 5
20:03:46 UTC 2013 pi at raspberry-pi:/usr/obj/usr/src/sys/RPI-B arm
I don't know (yet?) why the SVN version is missing, but I believe it is
the following SVN release I have.
Path: /usr/SVN/FreeBSD/base/head
Working Copy Root Path: /usr/SVN/FreeBSD/base/head
URL: https://svn0.us-east.freebsd.org/base/head
Relative URL: ^/head
Repository Root: https://svn0.us-east.freebsd.org/base
Repository UUID: ccf9f872-aa2e-dd11-9fc8-001c23d0bc1f
Revision: 257540
Node Kind: directory
Schedule: normal
Last Changed Author: delphij
Last Changed Rev: 257539
Last Changed Date: 2013-11-02 02:16:10 +0100 (Sat, 02 Nov 2013)
I paste dmesg further below for your entertainment.
Upcoming issue for me to figure out is why pkg_* fails, though the
binaries are recently built (though I believe that this I have seen for
a couple of weeks or so hence it's not new), hoping to get back to
building ports. One just needs to be mildly patient since the RPI's
primary savings are on price and energy but less so on buildworld time
and the like :)
I appreciate everyone's work on the box and hope that this mail creates
more enthusiasm rather than inbox consumption. I am willing to share
the little I know but please appreciate if I may be a bit slow
responding, at times.
Best 73 es gn,
Peter.
---
Pasted dmesg follows.
---
KDB: debugger backends: ddb
KDB: current backend: ddb
Copyright (c) 1992-2013 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993,
1994
The Regents of the University of California. All rights
reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 11.0-CURRENT #0: Tue Nov 5 20:03:46 UTC 2013
pi at raspberry-pi:/usr/obj/usr/src/sys/RPI-B arm
FreeBSD clang version 3.3 (tags/RELEASE_33/final 183502) 20130610
CPU: ARM1176JZ-S rev 7 (ARM11J core)
Supported features: ARM_ISA THUMB2 JAZELLE ARMv4 Security_Ext
WB enabled LABT branch prediction enabled
16KB/32B 4-way instruction cache
16KB/32B 4-way write-back-locking-C data cache
real memory = 536870912 (512 MB)
avail memory = 385458176 (367 MB)
kbd0 at kbdmux0
random: <Software, Yarrow> initialized
fdtbus0: <Flattened Device Tree>
simplebus0: <Flattened device tree simple bus> mem
0x20000000-0x20ffffff on fdtbus0
intc0: <BCM2835 Interrupt Controller> mem 0x2000b200-0x2000b3ff on
simplebus0
systimer0: <BCM2835 System Timer> mem 0x20003000-0x20003fff irq
8,9,10,11 on simplebus0
Event timer "BCM2835 Event Timer 3" frequency 1000000 Hz quality 1000
Timecounter "BCM2835 Timecounter" frequency 1000000 Hz quality 1000
bcmwd0: <BCM2708/2835 Watchdog> mem 0x2010001c-0x20100027 on simplebus0
gpio0: <BCM2708/2835 GPIO controller> mem 0x20200000-0x202000af irq
57,59,58,60 on simplebus0
gpio0: read-only pins: 46,47,48,49,50,51,52,53.
gpio0: reserved pins: 48,49,50,51,52,53.
gpioc0: <GPIO controller> on gpio0
gpiobus0: <GPIO bus> on gpio0
iichb0: <BCM2708/2835 BSC controller> mem 0x20205000-0x2020501f irq 61
on simplebus0
iicbus0: <OFW I2C bus> on iichb0
iic0: <I2C generic I/O> on iicbus0
iichb1: <BCM2708/2835 BSC controller> mem 0x20804000-0x2080401f irq 61
on simplebus0
iicbus1: <OFW I2C bus> on iichb1
iic1: <I2C generic I/O> on iicbus1
spi0: <BCM2708/2835 SPI controller> mem 0x20204000-0x2020401f irq 62 on
simplebus0
spibus0: <OFW SPI bus> on spi0
bcm_dma0: <BCM2835 DMA Controller> mem
0x20007000-0x20007fff,0x20e05000-0x20e05fff irq
24,25,26,27,28,29,30,31,32,33,34,35,36 on simplebus0
mbox0: <BCM2835 VideoCore Mailbox> mem 0x2000b880-0x2000b8bf irq 1 on
simplebus0
sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x20300000-0x203000ff
irq 70 on simplebus0
mmc0: <MMC/SD bus> on sdhci_bcm0
uart0: <PrimeCell UART (PL011)> mem 0x20201000-0x20201fff irq 65 on
simplebus0
dwcotg0: <DWC OTG 2.0 integrated USB controller> mem
0x20980000-0x2099ffff irq 17 on simplebus0
usbus0 on dwcotg0
fb0: <BCM2835 framebuffer device> on fdtbus0
sc0: Unknown <16 virtual consoles, flags=0x300>
simplebus1: <Flattened device tree simple bus> on fdtbus0
Timecounters tick every 10.000 msec
usbus0: 480Mbps High Speed USB v2.0
ugen0.1: <DWCOTG> at usbus0
uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on
usbus0
mmcsd0: 16GB <SDHC 00000 1.0 SN 201172550 MFG 02/2012 by 27 SM> at mmc0
50.0MHz/4bit/65535-block
fb0: 1280x1024(0x0 at 0,0) 16bpp
fb0: pitch 2560, base 0x58006000, screen_size 2621440
random: unblocking device.
Root mount waiting for: usbus0
uhub0: 1 port with 1 removable, self powered
Root mount waiting for: usbus0
ugen0.2: <vendor 0x0424> at usbus0
uhub1: <vendor 0x0424 product 0x9512, class 9/0, rev 2.00/2.00, addr 2>
on usbus0
uhub1: MTT enabled
uhub1: 3 ports with 2 removable, self powered
Root mount waiting for: usbus0
ugen0.3: <vendor 0x0424> at usbus0
smsc0: <vendor 0x0424 product 0xec00, rev 2.00/2.00, addr 3> on usbus0
Trying to mount root from ufs:/dev/mmcsd0s2a [rw,noatime]...
smsc0: chip 0xec00, rev. 0002
warning: no time-of-day clock registered, system time will not be set
accurately
miibus0: <MII bus> on smsc0
ukphy0: <Generic IEEE 802.3u media interface> PHY 1 on miibus0
ukphy0: none, 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
ue0: <USB Ethernet> on smsc0
ue0: Ethernet address: xx:xx:xx:xx:xx:xx
smsc0: chip 0xec00, rev. 0002
pid 814 (bash), uid 0: exited on signal 6 (core dumped)
pid 842 (pkg_info), uid 0: exited on signal 6
pid 845 (pkg-static), uid 0: exited on signal 12
pid 864 (pkg-static), uid 0: exited on signal 12
More information about the freebsd-arm
mailing list