ata(4) problem (unable to burn CDs)
Mario Pavlov
freebsd at abv.bg
Sat Jan 5 07:21:19 PST 2008
an important detail that I forgot to mention is that my DVD burner is SATA
>Hi guys,
>I'm experiencing problems with my DVD burner. I can't burn CDs.
>When I start k3b and load some data and start the burning it just never starts writing and I'm getting the fallowing errors in the messages log
>
>************************************************************************************************************************
>Jan 5 09:59:15 e-soul kernel: acd0: FAILURE - READ_DVD_STRUCTURE ILLEGAL REQUEST asc=0x30 ascq=0x02
>Jan 5 09:59:15 e-soul kernel: acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>Jan 5 09:59:17 e-soul last message repeated 3 times
>Jan 5 09:59:19 e-soul kernel: acd0: FAILURE - READ_TOC ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>Jan 5 09:59:19 e-soul kernel: acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>Jan 5 09:59:19 e-soul kernel: acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>Jan 5 10:02:45 e-soul kernel: acd0: FAILURE - WRITE_BIG timed out
>Jan 5 10:06:17 e-soul kernel: acd0: FAILURE - WRITE_BIG timed out
>Jan 5 10:06:25 e-soul kernel: acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>Jan 5 10:06:25 e-soul kernel: acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>************************************************************************************************************************
>
>
>and this is the k3b debug output after I hit cancel
>
>
>************************************************************************************************************************
>System
>-----------------------
>K3b Version: 1.0.4
>
>KDE Version: 3.5.8
>QT Version: 3.3.8
>Kernel: 7.0-PRERELEASE
>Devices
>-----------------------
>HL-DT-ST DVDRAM GSA-H62N CL00 (/dev/cd0, ) [CD-R, CD-RW, CD-ROM, DVD-ROM, DVD-R, DVD-RW, DVD-R DL, DVD+R, DVD+RW, DVD+R DL] [DVD-ROM, DVD-R Sequential, DVD-R Dual Layer Sequential, DVD-R Dual Layer Jump, DVD-RAM, DVD-RW Restricted Overwrite, DVD-RW Sequential, DVD+RW, DVD+R, DVD+R Dual Layer, CD-ROM, CD-R, CD-RW] [SAO, TAO, RAW, SAO/R96P, SAO/R96R, RAW/R16, RAW/R96P, RAW/R96R, Restricted Overwrite, Layer Jump]
>
>Used versions
>-----------------------
>cdrecord: 2.1
>
>cdrecord
>-----------------------
>/usr/local/bin/cdrecord: Operation not permitted. WARNING: Cannot set RR-scheduler
>/usr/local/bin/cdrecord: Permission denied. WARNING: Cannot set priority using setpriority().
>/usr/local/bin/cdrecord: WARNING: This causes a high risk for buffer underruns.
>scsidev: '4,0,0'
>scsibus: 4 target: 0 lun: 0
>SCSI buffer size: 64512
>/usr/local/bin/cdrecord: This version of cdrecord does not include DVD-R/DVD-RW support code.
>/usr/local/bin/cdrecord: If you need DVD-R/DVD-RW support, ask the Author for cdrecord-ProDVD.
>/usr/local/bin/cdrecord: Free test versions and free keys for personal use are at ftp://ftp.berlios.de/pub/cdrecord/ProDVD/
>Cdrecord-Clone 2.01 (amd64-unknown-freebsd7.0) Copyright (C) 1995-2004 Jörg Schilling
>TOC Type: 1 = CD-ROM
>Using libscg version 'schily-0.8'.
>Driveropts: 'burnfree'
>atapi: 0
>Device type : Removable CD-ROM
>Version : 0
>Response Format: 2
>Capabilities :
>Vendor_info : 'HL-DT-ST'
>Identifikation : 'DVDRAM GSA-H62N '
>Revision : 'CL00'
>Device seems to be: Generic mmc2 DVD-R/DVD-RW.
>Current: 0x0009
>Profile: 0x0012
>Profile: 0x0011
>Profile: 0x0015
>Profile: 0x0016
>Profile: 0x0014
>Profile: 0x0013
>Profile: 0x001A
>Profile: 0x001B
>Profile: 0x002B
>Profile: 0x0010
>Profile: 0x0009 (current)
>Profile: 0x000A
>Profile: 0x0008
>Profile: 0x0002
>Using generic SCSI-3/mmc CD-R/CD-RW driver (mmc_cdr).
>Driver flags : MMC-3 SWABAUDIO BURNFREE
>Supported modes: TAO PACKET SAO SAO/R96P SAO/R96R RAW/R16 RAW/R96P RAW/R96R
>Drive buf size : 1053696 = 1029 KB
>Drive DMA Speed: 5634 kB/s 32x CD 4x DVD
>FIFO size : 4194304 = 4096 KB
>/usr/local/bin/cdrecord: Operation not permitted. WARNING: Cannot set RR-scheduler
>/usr/local/bin/cdrecord: Permission denied. WARNING: Cannot set priority using setpriority().
>/usr/local/bin/cdrecord: WARNING: This causes a high risk for buffer underruns.
>/usr/local/bin/cdrecord: DMA speed too slow (OK for 26x). Cannot write at speed 48x.
>Track 01: data 671 MB
>Total size: 770 MB (76:22.93) = 343720 sectors
>Lout start: 771 MB (76:24/70) = 343720 sectors
>Current Secsize: 2048
>ATIP info from disk:
> Indicated writing power: 4
> Is not unrestricted
> Is not erasable
> Disk sub type: Medium Type A, low Beta category (A-) (2)
> ATIP start of lead in: -12508 (97:15/17)
> ATIP start of lead out: 359845 (79:59/70)
>Disk type: Short strategy type (Phthalocyanine or similar)
>Manuf. index: 22
>Manufacturer: Ritek Co.
>Blocks total: 359845 Blocks current: 359845 Blocks remaining: 16125
>Starting to write CD/DVD at speed 48 in real SAO mode for single session.
>Last chance to quit, starting real write in 2 seconds.
> 1 seconds.
> 0 seconds. Operation starts.
>Waiting for reader process to fill input buffer ... input buffer ready.
>BURN-Free is ON.
>Performing OPC...
>Sending CUE sheet...
>/usr/local/bin/cdrecord: WARNING: Drive returns wrong startsec (0) using -150
>/usr/local/bin/cdrecord: Input/output error. write_g1: scsi sendcmd: cmd timeout after 206.695 (200) s
>CDB: 2A 00 FF FF FF 6A 00 00 1F 00
>cmd finished after 206.695s timeout 200s
>/usr/local/bin/cdrecord: Input/output error. read buffer cap: scsi sendcmd: retryable error
>CDB: 5C 00 00 00 00 00 00 00 0C 00
>status: 0x2 (CHECK CONDITION)
>Sense Bytes: 70 00 06 00 00 00 00 0A 00 00 00 80 29 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
>Sense Key: 0x6 Unit Attention, Segment 0
>Sense Code: 0x29 Qual 0x00 (power on, reset, or bus device reset occurred) Fru 0x0
>Sense flags: Blk 0 (not valid)
>cmd finished after 5.095s timeout 200s
>Writing pregap for track 1 at -150
>write track pad data: error after 0 bytes
>Starting new track at sector: 0
>Track 01: 0 of 671 MB written.
>/usr/local/bin/cdrecord: faio_wait_on_buffer for writer timed out.
>/usr/local/bin/cdrecord: Caught interrupt.
>Track 01: data 671 MB
>Total size: 770 MB (76:22.93) = 343720 sectors
>Lout start: 771 MB (76:24/70) = 343720 sectors
>Current Secsize: 2048
>ATIP info from disk:
> Indicated writing power: 4
> Is not unrestricted
> Is not erasable
> Disk sub type: Medium Type A, low Beta category (A-) (2)
> ATIP start of lead in: -12508 (97:15/17)
> ATIP start of lead out: 359845 (79:59/70)
>Disk type: Short strategy type (Phthalocyanine or similar)
>Manuf. index: 22
>Manufacturer: Ritek Co.
>Blocks total: 359845 Blocks current: 359845 Blocks remaining: 16125
>Writing time: 426.405s
>/usr/local/bin/cdrecord: fifo had 64 puts and 1 gets.
>/usr/local/bin/cdrecord: fifo was 0 times empty and 0 times full, min fill was 100%.
>
>cdrecord command:
>-----------------------
>/usr/local/bin/cdrecord -v gracetime=2 dev=4,0,0 speed=48 -dao driveropts=burnfree -eject -data -tsize=343720s -
>************************************************************************************************************************
>
>
>cdrecord is complaining about permissions but I have this in /etc/devfs.conf
>
>
>************************************************************************************************************************
>perm cdrom 0666
>own cdrom root:operator
>link cd0 cdwriter
>perm cdwriter 0666
>own cdwriter root:operator
>perm pass0 0666
>own pass0 root:operator
>perm xpt0 0666
>own xpt0 root:operator
>************************************************************************************************************************
>
>
>and also
>
>
>************************************************************************************************************************
>$ ls -l acd0 cd0 pass0 xpt0
>crw-rw-rw- 1 root operator 0, 101 Jan 4 20:59 acd0
>crw-rw-rw- 1 root operator 0, 104 Jan 4 20:59 cd0
>crw-rw-rw- 1 root operator 0, 100 Jan 4 20:59 pass0
>crw-rw-rw- 1 root operator 0, 81 Jan 4 20:59 xpt0
>************************************************************************************************************************
>
>
>I have atapicam compiled in the kernel
>I've found similar problem reported in the freebsd-stable mailing list
>here is the thread http://lists.freebsd.org/pipermail/freebsd-stable/2007-May/035257.html
>
>I'm running the latest code from RELENG_7 for amd64
>
>
>************************************************************************************************************************
>$ uname -a
>FreeBSD e-soul.org 7.0-PRERELEASE FreeBSD 7.0-PRERELEASE #6: Fri Jan 4 12:27:16 EET 2008 root at e-soul.org:/usr/obj/usr/src/sys/Ss amd64
>************************************************************************************************************************
>
>
>************************************************************************************************************************
>$ dmesg
>Copyright (c) 1992-2008 The FreeBSD Project.
>Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
>FreeBSD is a registered trademark of The FreeBSD Foundation.
>FreeBSD 7.0-PRERELEASE #6: Fri Jan 4 12:27:16 EET 2008
> root at e-soul.org:/usr/obj/usr/src/sys/Ss
>Timecounter "i8254" frequency 1193182 Hz quality 0
>CPU: Intel(R) Core(TM)2 Duo CPU E4500 @ 2.20GHz (2206.71-MHz K8-class CPU)
> Origin = "GenuineIntel" Id = 0x6fd Stepping = 13
> Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
> Features2=0xe39d<SSE3,RSVD2,MON,DS_CPL,EST,TM2,SSSE3,CX16,xTPR,PDCM>
> AMD Features=0x20100800<SYSCALL,NX,LM>
> AMD Features2=0x1<LAHF>
> Cores per package: 2
>usable memory = 4285259776 (4086 MB)
>avail memory = 4084604928 (3895 MB)
>ACPI APIC Table: <MSTEST OEMAPIC >
>FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
> cpu0 (BSP): APIC ID: 0
> cpu1 (AP): APIC ID: 1
>ioapic0 <Version 2.0> irqs 0-23 on motherboard
>kbd1 at kbdmux0
>acpi0: <MSTEST OEMXSDT> on motherboard
>acpi0: [ITHREAD]
>acpi0: Power Button (fixed)
>acpi0: reservation of 0, a0000 (3) failed
>acpi0: reservation of 100000, 7ff00000 (3) failed
>Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
>acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
>acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
>Timecounter "HPET" frequency 14318180 Hz quality 900
>cpu0: <ACPI CPU> on acpi0
>ACPI Warning (tbutils-0243): Incorrect checksum in table [OEMB] - EB, should be E6 [20070320]
>est0: <Enhanced SpeedStep Frequency Control> on cpu0
>est: CPU supports Enhanced Speedstep, but is not recognized.
>est: cpu_vendor GenuineIntel, msr b280b2806000b28
>device_attach: est0 attach returned 6
>p4tcc0: <CPU Frequency Thermal Control> on cpu0
>cpu1: <ACPI CPU> on acpi0
>est1: <Enhanced SpeedStep Frequency Control> on cpu1
>est: CPU supports Enhanced Speedstep, but is not recognized.
>est: cpu_vendor GenuineIntel, msr b280b2806000b28
>device_attach: est1 attach returned 6
>p4tcc1: <CPU Frequency Thermal Control> on cpu1
>pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
>pci0: <ACPI PCI bus> on pcib0
>pcib1: <ACPI PCI-PCI bridge> irq 16 at device 1.0 on pci0
>pci1: <ACPI PCI bus> on pcib1
>vgapci0: <VGA-compatible display> port 0x8c00-0x8c7f mem 0xfd000000-0xfdffffff,0xc0000000-0xcfffffff,0xfc000000-0xfcffffff irq 16 at device 0.0 on pci1
>uhci0: <UHCI (generic) USB controller> port 0xdc00-0xdc1f irq 16 at device 26.0 on pci0
>uhci0: [GIANT-LOCKED]
>uhci0: [ITHREAD]
>usb0: <UHCI (generic) USB controller> on uhci0
>usb0: USB revision 1.0
>uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
>uhub0: 2 ports with 2 removable, self powered
>uhci1: <UHCI (generic) USB controller> port 0xe000-0xe01f irq 17 at device 26.1 on pci0
>uhci1: [GIANT-LOCKED]
>uhci1: [ITHREAD]
>usb1: <UHCI (generic) USB controller> on uhci1
>usb1: USB revision 1.0
>uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
>uhub1: 2 ports with 2 removable, self powered
>ehci0: <EHCI (generic) USB 2.0 controller> mem 0xfebffc00-0xfebfffff irq 18 at device 26.7 on pci0
>ehci0: [GIANT-LOCKED]
>ehci0: [ITHREAD]
>usb2: waiting for BIOS to give up control
>usb2: EHCI version 1.0
>usb2: companion controllers, 2 ports each: usb0 usb1
>usb2: <EHCI (generic) USB 2.0 controller> on ehci0
>usb2: USB revision 2.0
>uhub2: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb2
>uhub2: 4 ports with 4 removable, self powered
>pcm0: <Intel 82801H High Definition Audio Controller> mem 0xfebf8000-0xfebfbfff irq 22 at device 27.0 on pci0
>pcm0: [ITHREAD]
>pcib2: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
>pci4: <ACPI PCI bus> on pcib2
>pcib3: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
>pci3: <ACPI PCI bus> on pcib3
>re0: <RealTek 8168/8111B PCIe Gigabit Ethernet> port 0xa800-0xa8ff mem 0xfe9ff000-0xfe9fffff irq 19 at device 0.0 on pci3
>re0: Using 2 MSI messages
>miibus0: <MII bus> on re0
>rgephy0: <RTL8169S/8110S/8211B media interface> PHY 1 on miibus0
>rgephy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseT, 1000baseT-FDX, auto
>re0: Ethernet address: 00:1d:60:2a:4f:56
>re0: [FILTER]
>re0: [FILTER]
>pcib4: <ACPI PCI-PCI bridge> irq 16 at device 28.4 on pci0
>pci2: <ACPI PCI bus> on pcib4
>atapci0: <JMicron JMB363 SATA300 controller> port 0x9c00-0x9c07,0x9880-0x9883,0x9800-0x9807,0x9480-0x9483,0x9400-0x940f mem 0xfe8fe000-0xfe8fffff irq 16 at device 0.0 on pci2
>atapci0: [ITHREAD]
>atapci0: AHCI called from vendor specific driver
>atapci0: AHCI Version 01.00 controller with 2 ports detected
>ata2: <ATA channel 0> on atapci0
>ata2: [ITHREAD]
>ata3: <ATA channel 1> on atapci0
>ata3: [ITHREAD]
>ata4: <ATA channel 2> on atapci0
>ata4: [ITHREAD]
>uhci2: <UHCI (generic) USB controller> port 0xd480-0xd49f irq 23 at device 29.0 on pci0
>uhci2: [GIANT-LOCKED]
>uhci2: [ITHREAD]
>usb3: <UHCI (generic) USB controller> on uhci2
>usb3: USB revision 1.0
>uhub3: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb3
>uhub3: 2 ports with 2 removable, self powered
>uhci3: <UHCI (generic) USB controller> port 0xd800-0xd81f irq 19 at device 29.1 on pci0
>uhci3: [GIANT-LOCKED]
>uhci3: [ITHREAD]
>usb4: <UHCI (generic) USB controller> on uhci3
>usb4: USB revision 1.0
>uhub4: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb4
>uhub4: 2 ports with 2 removable, self powered
>uhci4: <UHCI (generic) USB controller> port 0xd880-0xd89f irq 18 at device 29.2 on pci0
>uhci4: [GIANT-LOCKED]
>uhci4: [ITHREAD]
>usb5: <UHCI (generic) USB controller> on uhci4
>usb5: USB revision 1.0
>uhub5: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb5
>uhub5: 2 ports with 2 removable, self powered
>ehci1: <EHCI (generic) USB 2.0 controller> mem 0xfebff800-0xfebffbff irq 23 at device 29.7 on pci0
>ehci1: [GIANT-LOCKED]
>ehci1: [ITHREAD]
>usb6: EHCI version 1.0
>usb6: companion controllers, 2 ports each: usb3 usb4 usb5
>usb6: <EHCI (generic) USB 2.0 controller> on ehci1
>usb6: USB revision 2.0
>uhub6: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb6
>uhub6: 6 ports with 6 removable, self powered
>pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
>pci5: <ACPI PCI bus> on pcib5
>dc0: <Davicom DM9102A 10/100BaseTX> port 0xb800-0xb8ff mem 0xfeaffc00-0xfeaffcff irq 22 at device 1.0 on pci5
>miibus1: <MII bus> on dc0
>amphy0: <DM9102 10/100 media interface> PHY 1 on miibus1
>amphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
>dc0: Ethernet address: 00:08:a1:27:88:1c
>dc0: [ITHREAD]
>rl0: <RealTek 8139 10/100BaseTX> port 0xb400-0xb4ff mem 0xfeaff800-0xfeaff8ff irq 23 at device 2.0 on pci5
>miibus2: <MII bus> on rl0
>rlphy0: <RealTek internal media interface> PHY 0 on miibus2
>rlphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
>rl0: Ethernet address: 00:19:e0:0e:a7:fa
>rl0: [ITHREAD]
>isab0: <PCI-ISA bridge> at device 31.0 on pci0
>isa0: <ISA bus> on isab0
>atapci1: <Intel ICH8 SATA300 controller> port 0xec00-0xec07,0xe880-0xe883,0xe800-0xe807,0xe480-0xe483,0xe400-0xe40f,0xe080-0xe08f irq 19 at device 31.2 on pci0
>atapci1: [ITHREAD]
>ata5: <ATA channel 0> on atapci1
>ata5: [ITHREAD]
>ata6: <ATA channel 1> on atapci1
>ata6: [ITHREAD]
>pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
>atapci2: <Intel ICH8 SATA300 controller> port 0xd400-0xd407,0xd080-0xd083,0xd000-0xd007,0xcc00-0xcc03,0xc880-0xc88f,0xc800-0xc80f irq 19 at device 31.5 on pci0
>atapci2: [ITHREAD]
>ata7: <ATA channel 0> on atapci2
>ata7: [ITHREAD]
>ata8: <ATA channel 1> on atapci2
>ata8: [ITHREAD]
>acpi_button0: <Power Button> on acpi0
>sio0: configured irq 4 not in bitmap of probed irqs 0
>sio0: port may not be enabled
>sio0: configured irq 4 not in bitmap of probed irqs 0
>sio0: port may not be enabled
>sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
>sio0: type 16550A
>sio0: [FILTER]
>atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
>atkbd0: <AT Keyboard> irq 1 on atkbdc0
>kbd0 at atkbd0
>atkbd0: [GIANT-LOCKED]
>atkbd0: [ITHREAD]
>psm0: <PS/2 Mouse> irq 12 on atkbdc0
>psm0: [GIANT-LOCKED]
>psm0: [ITHREAD]
>psm0: model IntelliMouse, device ID 3
>sc0: <System console> at flags 0x100 on isa0
>sc0: VGA <16 virtual consoles, flags=0x300>
>sio1: configured irq 3 not in bitmap of probed irqs 0
>sio1: port may not be enabled
>vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
>ukbd0: <vendor 0x04d9 USB Keyboard, class 0/0, rev 1.10/3.10, addr 2> on uhub3
>kbd2 at ukbd0
>uhid0: <vendor 0x04d9 USB Keyboard, class 0/0, rev 1.10/3.10, addr 2> on uhub3
>Timecounters tick every 1.000 msec
>ipfw2 initialized, divert enabled, rule-based forwarding enabled, default to deny, logging unlimited
>ad10: 476940MB <Seagate ST3500320AS SD15> at ata5-master SATA150
>acd0: DVDR <HL-DT-ST DVDRAM GSA-H62N/CL00> at ata6-master SATA150
>pcm0: <HDA Codec: Analog Devices AD1988>
>pcm0: <HDA Driver Revision: 20071129_0050>
>SMP: AP CPU #1 Launched!
>acd0: FAILURE - INQUIRY ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x01
>cd0 at ata4 bus 0 target 0 lun 0
>cd0: <HL-DT-ST DVDRAM GSA-H62N CL00> Removable CD-ROM SCSI-0 device
>cd0: 3.300MB/s transfers
>cd0: cd present [325318 x 2048 byte records]
>GEOM_LABEL: Label for provider acd0 is iso9660/BROODWAR.
>Trying to mount root from ufs:/dev/ad10s2a
>re0: link state changed to UP
>dc0: link state changed to DOWN
>dc0: link state changed to UP
>acd0: FAILURE - READ_DVD_STRUCTURE ILLEGAL REQUEST asc=0x30 ascq=0x02
>acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - READ_TOC ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - WRITE_BIG timed out
>acd0: FAILURE - WRITE_BIG timed out
>acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - READ_DVD_STRUCTURE ILLEGAL REQUEST asc=0x30 ascq=0x02
>acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - READ_TOC ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - WRITE_BIG timed out
>acd0: FAILURE - WRITE_BIG timed out
>acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>acd0: FAILURE - MODE_SENSE_BIG ILLEGAL REQUEST asc=0x24 ascq=0x00 sks=0x40 0x00 0x02
>************************************************************************************************************************
>
>this was all working on my previous machine running 7.0 BETA-3 for i386
>
>I've tested this DVD burner on windows and it's working
>
>anyone having the same problem ?
>
>Regards
>MGP
More information about the freebsd-amd64
mailing list