Panic when connecting USB drive to amd64
Ben Stuyts
ben at altesco.nl
Fri Feb 8 10:02:54 PST 2008
I wrote:
> Excuse the crosspost, I don't know if this is amd64 specific or not.
I have connected the same drive to a different system, running a
somewhat older version of i386 7.0, and it does not panic. So maybe it
is amd64 specific. Here are the drive's details that came up:
Feb 8 18:54:56 jirad kernel: umass1: <LaCie LaCie Hard Drive USB,
class 0/0, rev 2.00/0.00, addr 2> on uhub4
Feb 8 18:54:56 jirad root: Unknown USB device: vendor 0x059f product
0x0c41 bus uhub4
Feb 8 18:54:56 jirad kernel: da4 at umass-sim1 bus 1 target 0 lun 0
Feb 8 18:54:56 jirad kernel: da4: <SAMSUNG HM250JI > Fixed Direct
Access SCSI-2 device
Feb 8 18:54:56 jirad kernel: da4: 40.000MB/s transfers
Feb 8 18:54:56 jirad kernel: da4: 238475MB (488397168 512 byte
sectors: 255H 63S/T 30401C)
Feb 8 18:54:56 jirad kernel: GEOM_LABEL: Label for provider da4s1 is
msdosfs/LACIE.
uname -a:
FreeBSD jirad.altus-escon.com 7.0-BETA4 FreeBSD 7.0-BETA4 #3: Tue Dec
4 17:03:57 CET 2007 root at jirad.altus-escon.com:/usr/obj/usr/src/
sys/GENERIC i386
With kind regards,
Ben
> I have a consistent panic when I connect a 2.5" LaCie 250 GB drive
> to a SuperMicro 6015P-TR. This server is running amd64 with ZFS and
> I want to investigate a way to use ZFS send/receive to external USB
> drives for backup.
>
> Here is the panic message:
>
> Fatal trap 12: page fault while in kernel mode
> cpuid = 0; apic id = 00
> fault virtual address = 0x290
> fault code = supervisor read data, page not present
> instruction pointer = 0x8:0xffffffff803ff8aa
> stack pointer = 0x10:0xffffffffd72eed70
> frame pointer = 0x10:0xffffffffd72eedb0
> code segment = base 0x0, limit 0xfffff, type 0x1b
> = DPL 0, pres 1, long 1, def32 0, gran 1
> processor eflags = interrupt enabled, resume, IOPL = 0
> current process = 48 (usb3)
> [thread pid 48 tid 100047 ]
> Stopped at usb_transfer_complete+0x10a: movq 0x290(%rax),
> %rax
> db> tr
> Tracing pid 48 tid 100047 td 0xffffff00034fe350
> usb_transfer_complete() at usb_transfer_complete+0x10a
> usbd_start_transfer() at usbd_start_transfer+0x1a1
> bus_dmamap_load() at bus_dmamap_load+0x453
> usbd_transfer() at usbd_transfer+0xae
> usbd_sync_transfer() at usbd_sync_transfer+0xe
> usbd_do_request_flags_pipe() at usbd_do_request_flags_pipe+0x96
> usbd_do_request_flags() at usbd_do_request_flags+0x25
> usbd_get_string_desc() at usbd_get_string_desc+0x88
> usbd_get_string() at usbd_get_string+0xcd
> usbd_devinfo_vp() at usbd_devinfo_vp+0x80
> usbd_devinfo() at usbd_devinfo+0x46
> usbd_new_device() at usbd_new_device+0x68b
> uhub_explore() at uhub_explore+0x295
> usb_discover() at usb_discover+0x38
> usb_event_thread() at usb_event_thread+0x9f
> fork_exit() at fork_exit+0x12b
> fork_trampoline() at fork_trampoline+0xe
> --- trap 0, rip = 0, rsp = 0xffffffffd72efd30, rbp = 0 ---
>
> Here is the dmesg:
>
> Copyright (c) 1992-2008 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993,
> 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD is a registered trademark of The FreeBSD Foundation.
> FreeBSD 7.0-PRERELEASE #15: Wed Feb 6 16:07:55 CET 2008
> root at mars.altus-escon.com:/usr/obj/usr/src/sys/MARS
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Intel(R) Xeon(R) CPU E5335 @ 2.00GHz (2000.08-MHz K8-
> class CPU)
> Origin = "GenuineIntel" Id = 0x6f7 Stepping = 7
>
> Features
> =
> 0xbfebfbff
> <
> FPU
> ,VME
> ,DE
> ,PSE
> ,TSC
> ,MSR
> ,PAE
> ,MCE
> ,CX8
> ,APIC
> ,SEP
> ,MTRR
> ,PGE
> ,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
>
> Features2
> =0x4e33d<SSE3,RSVD2,MON,DS_CPL,VMX,TM2,SSSE3,CX16,xTPR,PDCM,DCA>
> AMD Features=0x20100800<SYSCALL,NX,LM>
> AMD Features2=0x1<LAHF>
> Cores per package: 4
> usable memory = 4280487936 (4082 MB)
> avail memory = 4117889024 (3927 MB)
> ACPI APIC Table: <PTLTD APIC >
> FreeBSD/SMP: Multiprocessor System Detected: 8 CPUs
> cpu0 (BSP): APIC ID: 0
> cpu1 (AP): APIC ID: 1
> cpu2 (AP): APIC ID: 2
> cpu3 (AP): APIC ID: 3
> cpu4 (AP): APIC ID: 4
> cpu5 (AP): APIC ID: 5
> cpu6 (AP): APIC ID: 6
> cpu7 (AP): APIC ID: 7
> ioapic0 <Version 2.0> irqs 0-23 on motherboard
> ioapic1 <Version 2.0> irqs 24-47 on motherboard
> kbd1 at kbdmux0
> ath_hal: 0.9.20.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413,
> RF5413)
> acpi0: <PTLTD RSDT> on motherboard
> acpi0: [ITHREAD]
> acpi0: Power Button (fixed)
> Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
> acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
> cpu0: <ACPI CPU> on acpi0
> p4tcc0: <CPU Frequency Thermal Control> on cpu0
> cpu1: <ACPI CPU> on acpi0
> p4tcc1: <CPU Frequency Thermal Control> on cpu1
> cpu2: <ACPI CPU> on acpi0
> p4tcc2: <CPU Frequency Thermal Control> on cpu2
> cpu3: <ACPI CPU> on acpi0
> p4tcc3: <CPU Frequency Thermal Control> on cpu3
> cpu4: <ACPI CPU> on acpi0
> p4tcc4: <CPU Frequency Thermal Control> on cpu4
> cpu5: <ACPI CPU> on acpi0
> p4tcc5: <CPU Frequency Thermal Control> on cpu5
> cpu6: <ACPI CPU> on acpi0
> p4tcc6: <CPU Frequency Thermal Control> on cpu6
> cpu7: <ACPI CPU> on acpi0
> p4tcc7: <CPU Frequency Thermal Control> on cpu7
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> pcib1: <ACPI PCI-PCI bridge> at device 2.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> pcib2: <ACPI PCI-PCI bridge> irq 16 at device 0.0 on pci1
> pci2: <ACPI PCI bus> on pcib2
> pcib3: <ACPI PCI-PCI bridge> irq 16 at device 0.0 on pci2
> pci3: <ACPI PCI bus> on pcib3
> pcib4: <ACPI PCI-PCI bridge> at device 0.0 on pci3
> pci4: <ACPI PCI bus> on pcib4
> pcib5: <ACPI PCI-PCI bridge> irq 18 at device 2.0 on pci2
> pci5: <ACPI PCI bus> on pcib5
> em0: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port
> 0x2000-0x201f mem 0xd8000000-0xd801ffff irq 18 at device 0.0 on pci5
> em0: Using MSI interrupt
> em0: Ethernet address: 00:30:48:7b:88:7e
> em0: [FILTER]
> em1: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port
> 0x2020-0x203f mem 0xd8020000-0xd803ffff irq 19 at device 0.1 on pci5
> em1: Using MSI interrupt
> em1: Ethernet address: 00:30:48:7b:88:7f
> em1: [FILTER]
> pcib6: <ACPI PCI-PCI bridge> at device 0.3 on pci1
> pci6: <ACPI PCI bus> on pcib6
> puc0: <NetMos NM9835 Dual UART and 1284 Printer port> port
> 0x3030-0x3037,0x3028-0x302f,0x3020-0x3027,0x3018-0x301f,
> 0x3010-0x3017,0x3000-0x300f irq 24 at device 1.0 on pci6
> puc0: [FILTER]
> uart0: <Non-standard ns8250 class UART with FIFOs> on puc0
> uart0: [FILTER]
> uart1: <Non-standard ns8250 class UART with FIFOs> on puc0
> uart1: [FILTER]
> ppc0: <Parallel port> on puc0
> ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
> ppbus0: <Parallel port bus> on ppc0
> plip0: cannot reserve interrupt, failed.
> lpt0: <Printer> on ppbus0
> lpt0: Polled port
> ppi0: <Parallel I/O> on ppbus0
> pcib7: <ACPI PCI-PCI bridge> at device 4.0 on pci0
> pci7: <ACPI PCI bus> on pcib7
> pcib8: <ACPI PCI-PCI bridge> at device 6.0 on pci0
> pci8: <ACPI PCI bus> on pcib8
> pci0: <base peripheral> at device 8.0 (no driver attached)
> uhci0: <Intel 631XESB/632XESB/3100 USB controller USB-1> port
> 0x1800-0x181f irq 17 at device 29.0 on pci0
> uhci0: [GIANT-LOCKED]
> uhci0: [ITHREAD]
> usb0: <Intel 631XESB/632XESB/3100 USB controller USB-1> on uhci0
> usb0: USB revision 1.0
> uhub0: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb0
> uhub0: 2 ports with 2 removable, self powered
> uhci1: <Intel 631XESB/632XESB/3100 USB controller USB-2> port
> 0x1820-0x183f irq 19 at device 29.1 on pci0
> uhci1: [GIANT-LOCKED]
> uhci1: [ITHREAD]
> usb1: <Intel 631XESB/632XESB/3100 USB controller USB-2> on uhci1
> usb1: USB revision 1.0
> uhub1: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb1
> uhub1: 2 ports with 2 removable, self powered
> uhci2: <Intel 631XESB/632XESB/3100 USB controller USB-3> port
> 0x1840-0x185f irq 18 at device 29.2 on pci0
> uhci2: [GIANT-LOCKED]
> uhci2: [ITHREAD]
> usb2: <Intel 631XESB/632XESB/3100 USB controller USB-3> on uhci2
> usb2: USB revision 1.0
> uhub2: <Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1> on usb2
> uhub2: 2 ports with 2 removable, self powered
> ehci0: <Intel 63XXESB USB 2.0 controller> mem 0xd8500000-0xd85003ff
> irq 17 at device 29.7 on pci0
> ehci0: [GIANT-LOCKED]
> ehci0: [ITHREAD]
> usb3: EHCI version 1.0
> usb3: companion controllers, 2 ports each: usb0 usb1 usb2
> usb3: <Intel 63XXESB USB 2.0 controller> on ehci0
> usb3: USB revision 2.0
> uhub3: <Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1> on usb3
> uhub3: 6 ports with 6 removable, self powered
> umass0: <Peppercon AG Multidevice, class 0/0, rev 2.00/0.01, addr 2>
> on uhub3
> uhid0: <Peppercon AG Multidevice, class 0/0, rev 2.00/0.01, addr 2>
> on uhub3
> ukbd0: <Peppercon AG Multidevice, class 0/0, rev 2.00/0.01, addr 2>
> on uhub3
> kbd2 at ukbd0
> pcib9: <ACPI PCI-PCI bridge> at device 30.0 on pci0
> pci9: <ACPI PCI bus> on pcib9
> vgapci0: <VGA-compatible display> port 0x4000-0x40ff mem
> 0xd0000000-0xd7ffffff,0xd8220000-0xd822ffff irq 18 at device 1.0 on
> pci9
> em2: <Intel(R) PRO/1000 Network Connection Version - 6.7.3> port
> 0x4400-0x443f mem 0xd8200000-0xd821ffff irq 16 at device 2.0 on pci9
> em2: Ethernet address: 00:30:48:44:1a:ab
> em2: [FILTER]
> isab0: <PCI-ISA bridge> at device 31.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel 63XXESB2 UDMA100 controller> port
> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1860-0x186f at device 31.1 on
> pci0
> ata0: <ATA channel 0> on atapci0
> ata0: [ITHREAD]
> ata1: <ATA channel 1> on atapci0
> ata1: [ITHREAD]
> atapci1: <Intel 63XXESB2 SATA300 controller> port
> 0x1890-0x1897,0x1884-0x1887,0x1888-0x188f,
> 0x1880-0x1883,0x1870-0x187f mem 0xd8500400-0xd85007ff irq 19 at
> device 31.2 on pci0
> atapci1: [ITHREAD]
> ata2: <ATA channel 0> on atapci1
> ata2: [ITHREAD]
> ata3: <ATA channel 1> on atapci1
> ata3: [ITHREAD]
> pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
> acpi_button0: <Power Button> on acpi0
> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
> atkbd0: <AT Keyboard> irq 1 on atkbdc0
> kbd0 at atkbd0
> atkbd0: [GIANT-LOCKED]
> atkbd0: [ITHREAD]
> sio0: configured irq 4 not in bitmap of probed irqs 0
> sio0: port may not be enabled
> sio0: configured irq 4 not in bitmap of probed irqs 0
> sio0: port may not be enabled
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10
> on acpi0
> sio0: type 16550A, console
> sio0: [FILTER]
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
> sio1: type 16550A
> sio1: [FILTER]
> fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2
> on acpi0
> fdc0: [FILTER]
> fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> orm0: <ISA Option ROM> at iomem 0xc0000-0xcafff on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x100>
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on
> isa0
> WARNING: ZFS is considered to be an experimental feature in FreeBSD.
> Timecounters tick every 1.000 msec
> ipfw2 (+ipv6) initialized, divert enabled, rule-based forwarding
> disabled, default to deny, logging limited to 50 packets/entry by
> default
> ZFS filesystem version 6
> ZFS storage pool version 6
> acd0: DMA limited to UDMA33, controller found non-ATA66 cable
> acd0: DVDROM <MATSHITADVD-ROM SR-8178/PZ16> at ata0-slave UDMA33
> ad4: 143089MB <WDC WD1500ADFD-00NLR5 21.07QR5> at ata2-master SATA150
> ad6: 143089MB <WDC WD1500ADFD-00NLR5 21.07QR5> at ata3-master SATA150
> SMP: AP CPU #1 Launched!
> SMP: AP CPU #3 Launched!
> SMP: AP CPU #2 Launched!
> SMP: AP CPU #5 Launched!
> SMP: AP CPU #4 Launched!
> SMP: AP CPU #6 Launched!
> SMP: AP CPU #7 Launched!
> da0 at umass-sim0 bus 0 target 0 lun 0
> da0: <PepperC Virtual Disc 1 0.01> Removable Direct Access SCSI-3
> device
> da0: 40.000MB/s transfers
> da0: Attempt to query device size failed: NOT READY, Medium not
> present
> Trying to mount root from zfs:tank
>
> Please let me know if there is anything I can do to help debug this.
> This is not (yet) a production server, so I can try out various
> things if needed.
>
> With kind regards,
> Ben
>
> _______________________________________________
> freebsd-current at freebsd.org mailing list
> http://lists.freebsd.org/mailman/listinfo/freebsd-current
> To unsubscribe, send any mail to "freebsd-current-unsubscribe at freebsd.org
> "
>
More information about the freebsd-amd64
mailing list