amd64/89550: [amd64] sym0: VTOBUS failed (6.0 Release)

[Cedric Ware]

The following reply was made to PR amd64/89550; it has been noted by GNATS.

From: Cedric Ware <cedric.ware at enst.fr>
To: bug-followup at FreeBSD.org, awallac3 at uiuc.edu
Cc:  
Subject: Re: amd64/89550: [amd64] sym0: VTOBUS failed (6.0 Release)
Date: Mon, 20 Mar 2006 23:07:19 +0100

 	Hello,
 
 On Fri, 25 Nov 2005, Scott Long wrote:
 > I'm already working on fixing this.
 
 Any success?
 
 I think I've been hit by a similar problem trying to upgrade from
 FreeBSD 5.x/i386 to 6.x/amd64 on an AND Athlon 64 X2 3800+, with a
 Tekram DC-390 SCSI adapter.
 
 When booting from the FreeBSD install CD-ROM (6.1-BETA3 as well as
 6.1-20060320-STABLE-amd64), the boot stops with a panic; I'm not
 sure it always does at the same place, I noted one at device scan:
 ______________________________________________________
 
 Waiting 5 seconds for SCSI devices to settle
 (noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
 (noperiph:sym1:0:-1:-1): SCSI BUS reset delivered.
 panic: sym: VTOBUS FAILED!
 
 Uptime: 6s
 Cannot dump.  No dump device defined.
 Automatic reboot in 15 seconds - press any key (etc.)
 ______________________________________________________
 
 Another happened after card detection; from memory, I think it was:
 ______________________________________________________
 
 sym0: <1010-33> port (etc.)
 panic: sym: VTOBUS FAILED!
 
 Uptime: 1s
 (etc.)
 ______________________________________________________
 
 My dmesg with FreeBSD 5 follows.  I haven't yet tried 6.x/i386.
 
 					Thanks in advance,
 					Cedric Ware.
 
 Copyright (c) 1992-2005 The FreeBSD Project.
 Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
         The Regents of the University of California. All rights reserved.
 FreeBSD 5.4-STABLE #15: Tue Nov  1 21:16:14 CET 2005
     ware at krakatoa:/data/usrobj/data/usrsrc/sys/KRAKATOA
 ACPI APIC Table: <A M I  OEMAPIC >
 Timecounter "i8254" frequency 1193182 Hz quality 0
 CPU: AMD Athlon(tm) 64 X2 Dual Core Processor 3800+ (2002.58-MHz 686-class CPU)
   Origin = "AuthenticAMD"  Id = 0x20f32  Stepping = 2
   Features=0x178bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2,HTT>
   Hyperthreading: 2 logical CPUs
   AMD Features=0xe0500000<NX,AMIE,LM,DSP,3DNow!>
 real memory  = 1073414144 (1023 MB)
 avail memory = 1040859136 (992 MB)
 FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
  cpu0 (BSP): APIC ID:  0
  cpu1 (AP): APIC ID:  1
 MADT: Forcing active-low polarity and level trigger for SCI
 ioapic0 <Version 0.3> irqs 0-23 on motherboard
 npx0: <math processor> on motherboard
 npx0: INT 16 interface
 acpi0: <A M I OEMRSDT> on motherboard
 acpi0: Power Button (fixed)
 Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
 acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
 cpu0: <ACPI CPU> on acpi0
 cpu1: <ACPI CPU> on acpi0
 pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
 pci0: <ACPI PCI bus> on pcib0
 agp0: <VIA K8T800Pro host to PCI bridge> mem 0xe4000000-0xe7ffffff at device 0.0 on pci0
 pcib1: <ACPI PCI-PCI bridge> at device 1.0 on pci0
 pci1: <ACPI PCI bus> on pcib1
 drm0: <ATI Radeon RV280 9200> port 0xe000-0xe0ff mem 0xfbe00000-0xfbe0ffff,0xe8000000-0xefffffff irq 16 at device 0.0 on pci1
 info: [drm] AGP at 0xe4000000 64MB
 info: [drm] Initialized radeon 1.11.0 20020828 on minor 0
 pci1: <display> at device 0.1 (no driver attached)
 fwohci0: <VIA Fire II (VT6306)> port 0x7400-0x747f mem 0xfb000000-0xfb0007ff irq 16 at device 7.0 on pci0
 fwohci0: OHCI version 1.0 (ROM=1)
 fwohci0: No. of Isochronous channels is 4.
 fwohci0: EUI64 00:11:d8:00:00:58:8f:4a
 fwohci0: Phy 1394a available S400, 2 ports.
 fwohci0: Link S400, max_rec 2048 bytes.
 firewire0: <IEEE1394(FireWire) bus> on fwohci0
 fwohci0: Initiate bus reset
 fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
 firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
 firewire0: bus manager 0 (me)
 atapci0: <Promise PDC20378 SATA150 controller> port 0x7800-0x787f,0x8800-0x880f,0x9800-0x983f mem 0xfb100000-0xfb11ffff,0xfb200000-0xfb200fff irq 18 at device 8.0 on pci0
 atapci0: failed: rid 0x20 is memory, requested 4
 ata2: channel #0 on atapci0
 ata3: channel #1 on atapci0
 ata4: channel #2 on atapci0
 skc0: <Marvell Gigabit Ethernet> port 0xa000-0xa0ff mem 0xfb400000-0xfb403fff irq 17 at device 10.0 on pci0
 skc0: Marvell Yukon Lite Gigabit Ethernet rev. (0x9)
 sk0: <Marvell Semiconductor, Inc. Yukon> on skc0
 sk0: Ethernet address: 00:13:d4:9b:6d:eb
 miibus0: <MII bus> on sk0
 e1000phy0: <Marvell 88E1000 Gigabit PHY> on miibus0
 e1000phy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX-FDX, auto
 sym0: <1010-33> port 0x8000-0x80ff mem 0xfb600000-0xfb601fff,0xfb700000-0xfb7003ff irq 18 at device 13.0 on pci0
 sym0: Symbios NVRAM, ID 7, Fast-80, LVD, parity checking
 sym0: open drain IRQ line driver, using on-chip SRAM
 sym0: using LOAD/STORE-based firmware.
 sym0: handling phase mismatch from SCRIPTS.
 sym0: SCAN AT BOOT disabled for targets 1 2 3 8 9 11 12 13 14 15.
 sym1: <1010-33> port 0x9000-0x90ff mem 0xfb900000-0xfb901fff,0xfba00000-0xfba003ff irq 18 at device 13.1 on pci0
 sym1: Symbios NVRAM, ID 7, Fast-80, SE, parity checking
 sym1: open drain IRQ line driver, using on-chip SRAM
 sym1: using LOAD/STORE-based firmware.
 sym1: handling phase mismatch from SCRIPTS.
 sym1: SCAN AT BOOT disabled for targets 2 5 8 9 10 11 12 13 14 15.
 atapci1: <VIA 6420 SATA150 controller> port 0xa400-0xa4ff,0xa800-0xa80f,0xb000-0xb003,0xb400-0xb407,0xb800-0xb803,0xc000-0xc007 irq 20 at device 15.0 on pci0
 ata5: channel #0 on atapci1
 ata6: channel #1 on atapci1
 atapci2: <VIA 8237 UDMA133 controller> port 0xfc00-0xfc0f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 15.1 on pci0
 ata0: channel #0 on atapci2
 ata1: channel #1 on atapci2
 uhci0: <VIA 83C572 USB controller> port 0xc400-0xc41f irq 21 at device 16.0 on pci0
 usb0: <VIA 83C572 USB controller> on uhci0
 usb0: USB revision 1.0
 uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub0: 2 ports with 2 removable, self powered
 uhci1: <VIA 83C572 USB controller> port 0xc800-0xc81f irq 21 at device 16.1 on pci0
 usb1: <VIA 83C572 USB controller> on uhci1
 usb1: USB revision 1.0
 uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub1: 2 ports with 2 removable, self powered
 uhci2: <VIA 83C572 USB controller> port 0xd000-0xd01f irq 21 at device 16.2 on pci0
 usb2: <VIA 83C572 USB controller> on uhci2
 usb2: USB revision 1.0
 uhub2: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub2: 2 ports with 2 removable, self powered
 uhci3: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 21 at device 16.3 on pci0
 usb3: <VIA 83C572 USB controller> on uhci3
 usb3: USB revision 1.0
 uhub3: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
 uhub3: 2 ports with 2 removable, self powered
 pci0: <serial bus, USB> at device 16.4 (no driver attached)
 isab0: <PCI-ISA bridge> at device 17.0 on pci0
 isa0: <ISA bus> on isab0
 pcm0: <VIA VT8237> port 0xd800-0xd8ff irq 22 at device 17.5 on pci0
 pcm0: <Avance Logic ALC850 AC97 Codec>
 acpi_button0: <Power Button> on acpi0
 acpi_button1: <Sleep Button> on acpi0
 atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
 atkbd0: <AT Keyboard> irq 1 on atkbdc0
 kbd0 at atkbd0
 psm0: <PS/2 Mouse> irq 12 on atkbdc0
 psm0: model MouseMan+, device ID 0
 fdc0: <floppy drive controller (FDE)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
 fd0: <1440-KB 3.5" drive> on fdc0 drive 0
 sio0: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 flags 0x10 on acpi0
 sio0: type 16550A
 sio1: configured irq 4 not in bitmap of probed irqs 0
 sio1: port may not be enabled
 sio1: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 on acpi0
 sio1: type 16550A
 orm0: <ISA Option ROMs> at iomem 0xcd000-0xd0fff,0xc0000-0xccfff on isa0
 pmtimer0 on isa0
 ppc0: parallel port not found.
 sc0: <System console> at flags 0x100 on isa0
 sc0: VGA <16 virtual consoles, flags=0x300>
 vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
 Timecounters tick every 10.000 msec
 ad0: 152627MB <ST3160023A/8.01> [310101/16/63] at ata0-master UDMA100
 acd0: DVDR <PIONEER DVD-RW DVR-109/1.17> at ata1-master UDMA66
 Waiting 5 seconds for SCSI devices to settle
 (noperiph:sym0:0:-1:-1): SCSI BUS reset delivered.
 (noperiph:sym1:0:-1:-1): SCSI BUS reset delivered.
 da0 at sym0 bus 0 target 0 lun 0
 da0: <SEAGATE ST336754LW 0002> Fixed Direct Access SCSI-3 device 
 da0: 160.000MB/s transfers (80.000MHz, offset 62, 16bit), Tagged Queueing Enabled
 da0: 35003MB (71687372 512 byte sectors: 255H 63S/T 4462C)
 SMP: AP CPU #1 Launched!
 cd0 at ata1 bus 0 target 0 lun 0
 cd0: <PIONEER DVD-RW  DVR-109 1.17> Removable CD-ROM SCSI-0 device 
 cd0: 66.000MB/s transfers
 cd0: Attempt to query device size failed: NOT READY, Medium not present
 Mounting root from ufs:/dev/ad0s2a