Dmesg errors

Tue Aug 22 12:01:29 UTC 2006

> -----Original Message-----
> From: owner-freebsd-amd64 at freebsd.org 
> [mailto:owner-freebsd-amd64 at freebsd.org] On Behalf Of Vizion
> Sent: Tuesday, August 22, 2006 4:16 AM
> To: amd64 at freebsd.org
> Subject: dmesg - errors
> 
> 
> There are a number of reports in dmesg I do not understand.
> 
> 
> \***  mark start of section 
> ***\  marks end of section
> for each query
> Can anyone please tell me what action, if any, I should take 
> for each section.
> Comment start is indicated by !!**
> Multi-line comments end with **!!
> 
> 
> 
> Thanks in advance.
> david
> ______________________________
> 
> 
> Copyright (c) 1992-2006 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 
> 1993, 1994
> 	The Regents of the University of California. All rights 
> reserved.
> FreeBSD 6.1-RELEASE #0: Sun May  7 04:15:57 UTC 2006
>     root at bloom.cse.buffalo.edu:/usr/obj/usr/src/sys/SMP
> ACPI APIC Table: <GBT    AWRDACPI>
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: AMD Athlon(tm) 64 Processor 3200+ (2009.16-MHz K8-class CPU)
>   Origin = "AuthenticAMD"  Id = 0x20ff2  Stepping = 2
>   
> Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP
> ,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
>   Features2=0x1<SSE3>
>   AMD Features=0xe2500800<SYSCALL,NX,MMX+,FFXSR,LM,3DNow+,3DNow>
>   AMD Features2=0x1<LAHF>
> real memory  = 2080309248 (1983 MB)
> avail memory = 1997578240 (1905 MB)
> ioapic0 <Version 1.1> irqs 0-23 on motherboard
> kbd0 at kbdmux0
> acpi0: <GBT AWRDACPI> on motherboard
> 
> \***
> acpi_bus_number: can't get _ADR
> acpi_bus_number: can't get _ADR
> acpi0: Power Button (fixed)
> acpi_bus_number: can't get _ADR
> acpi_bus_number: can't get _ADR
> acpi_bus_number: can't get _ADR
> acpi_bus_number: can't get _ADR
>     ACPI-0501: *** Error: Handler for [SystemMemory] returned 
> AE_AML_ALIGNMENT
>     ACPI-1304: *** Error: Method execution failed 
> [\\_SB_.MEM_._CRS] (Node 0xffffff0000bdbd80), AE_AML_ALIGNMENT
>     ACPI-0239: *** Error: Method execution failed 
> [\\_SB_.MEM_._CRS] (Node 0xffffff0000bdbd80), AE_AML_ALIGNMENT
> can't fetch resources for \\_SB_.MEM_ - AE_AML_ALIGNMENT
> 
> !!** what is going on here?
> ***\
> 
> 
> cpu0: <ACPI CPU> on acpi0
> acpi_button0: <Power Button> on acpi0
> pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
> pci0: <ACPI PCI bus> on pcib0
> 
> \***
> !!** Is this a follow up from previous section? 
> 
> pci0: <memory, RAM> at device 0.0 (no driver attached)
> pci0: <memory, RAM> at device 0.1 (no driver attached)
> pci0: <memory, RAM> at device 0.2 (no driver attached)
> pci0: <memory, RAM> at device 0.3 (no driver attached)
> pci0: <memory, RAM> at device 0.4 (no driver attached)
> pci0: <memory, RAM> at device 0.5 (no driver attached)
> pci0: <memory, RAM> at device 0.6 (no driver attached)
> pci0: <memory, RAM> at device 0.7 (no driver attached)
> pci0: <display, VGA> at device 5.0 (no driver attached)
> pci0: <memory, RAM> at device 9.0 (no driver attached)
> 
> ***\
> 
> isab0: <PCI-ISA bridge> at device 10.0 on pci0
> isa0: <ISA bus> on isab0
> pci0: <serial bus, SMBus> at device 10.1 (no driver attached)
> pci0: <memory, RAM> at device 10.2 (no driver attached)
> ohci0: <OHCI (generic) USB controller> mem 
> 0xf7008000-0xf7008fff irq 21 at device 11.0 on pci0
> ohci0: [GIANT-LOCKED]
> usb0: OHCI version 1.0, legacy support
> usb0: SMM does not respond, resetting
> usb0: <OHCI (generic) USB controller> on ohci0
> usb0: USB revision 1.0
> uhub0: nVidia OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 8 ports with 8 removable, self powered
> ehci0: <EHCI (generic) USB 2.0 controller> mem 
> 0xf7004000-0xf70040ff irq 22 at device 11.1 on pci0
> ehci0: [GIANT-LOCKED]
> usb1: EHCI version 1.0
> usb1: companion controller, 8 ports each: usb0
> usb1: <EHCI (generic) USB 2.0 controller> on ehci0
> usb1: USB revision 2.0
> uhub1: nVidia EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
> uhub1: 8 ports with 8 removable, self powered
> umass0: USB2.0 CardReader, rev 2.00/91.38, addr 2
> atapci0: <nVidia nForce MCP51 UDMA133 controller> port 
> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xf000-0xf00f at device 
> 13.0 on pci0
> ata0: <ATA channel 0> on atapci0
> ata1: <ATA channel 1> on atapci0
> atapci1: <nVidia nForce MCP51 SATA300 controller> port 
> 0x9f0-0x9f7,0xbf0-0xbf3,0x970-0x977,0xb70-0xb73,0xd800-0xd80f 
> mem 0xf7007000-0xf7007fff irq 23 at device 14.0 on pci0
> ata2: <ATA channel 0> on atapci1
> ata3: <ATA channel 1> on atapci1
> atapci2: <nVidia nForce MCP51 SATA300 controller> port 
> 0x9e0-0x9e7,0xbe0-0xbe3,0x960-0x967,0xb60-0xb63,0xc400-0xc40f 
> mem 0xf7006000-0xf7006fff irq 20 at device 15.0 on pci0
> ata4: <ATA channel 0> on atapci2
> ata5: <ATA channel 1> on atapci2
> pcib1: <ACPI PCI-PCI bridge> at device 16.0 on pci0
> pci1: <ACPI PCI bus> on pcib1
> fwohci0: <Texas Instruments TSB43AB23> mem 
> 0xf4005000-0xf40057ff,0xf4000000-0xf4003fff irq 16 at device 
> 6.0 on pci1
> fwohci0: OHCI version 1.10 (ROM=1)
> fwohci0: No. of Isochronous channels is 4.
> fwohci0: EUI64 00:d0:03:56:00:b2:b7:e6
> fwohci0: Phy 1394a available S400, 3 ports.
> fwohci0: Link S400, max_rec 2048 bytes.
> firewire0: <IEEE1394(FireWire) bus> on fwohci0
> fwe0: <Ethernet over FireWire> on firewire0
> if_fwe0: Fake Ethernet address: 02:d0:03:b2:b7:e6
> fwe0: Ethernet address: 02:d0:03:b2:b7:e6
> fwe0: if_start running deferred for Giant
> sbp0: <SBP-2/SCSI over FireWire> on firewire0
> fwohci0: Initiate bus reset
> fwohci0: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
> firewire0: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
> firewire0: bus manager 0 (me)
> rl0: <RealTek 8139 10/100BaseTX> port 0xa000-0xa0ff mem 
> 0xf4004000-0xf40040ff irq 17 at device 7.0 on pci1
> miibus0: <MII bus> on rl0
> rlphy0: <RealTek internal media interface> on miibus0
> rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> rl0: Ethernet address: 00:30:bd:b6:d9:e0
> fwohci1: <VIA Fire II (VT6306)> port 0xa400-0xa47f mem 
> 0xf4006000-0xf40067ff irq 18 at device 14.0 on pci1
> fwohci1: OHCI version 1.0 (ROM=1)
> fwohci1: No. of Isochronous channels is 4.
> fwohci1: EUI64 00:00:14:85:00:ca:4a:75
> fwohci1: Phy 1394a available S400, 2 ports.
> fwohci1: Link S400, max_rec 2048 bytes.
> firewire1: <IEEE1394(FireWire) bus> on fwohci1
> fwe1: <Ethernet over FireWire> on firewire1
> if_fwe1: Fake Ethernet address: 02:00:14:ca:4a:75
> fwe1: Ethernet address: 02:00:14:ca:4a:75
> fwe1: if_start running deferred for Giant
> sbp1: <SBP-2/SCSI over FireWire> on firewire1
> fwohci1: Initiate bus reset
> fwohci1: node_id=0xc800ffc0, gen=1, CYCLEMASTER mode
> firewire1: 1 nodes, maxhop <= 0, cable IRM = 0 (me)
> firewire1: bus manager 0 (me)
> pci0: <multimedia> at device 16.1 (no driver attached)
> pci0: <bridge> at device 20.0 (no driver attached)
> sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 
> flags 0x10 on acpi0
> sio0: type 16550A
> ppc0: <Standard parallel printer port> port 
> 0x378-0x37f,0x778-0x77b irq 7 on acpi0
> ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
> ppbus0: <Parallel port bus> on ppc0
> plip0: <PLIP network interface> on ppbus0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
> atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
> kbd1 at atkbd0
> atkbd0: [GIANT-LOCKED]
> psm0: <PS/2 Mouse> irq 12 on atkbdc0
> psm0: [GIANT-LOCKED]
> psm0: model IntelliMouse, device ID 3
> orm0: <ISA Option ROMs> at iomem 
> 0xd0000-0xd3fff,0xd4000-0xd57ff on isa0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio1: configured irq 3 not in bitmap of probed irqs 0
> sio1: port may not be enabled
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 
> 0xa0000-0xbffff on isa0
> Timecounter "TSC" frequency 2009158157 Hz quality 800
> Timecounters tick every 1.000 msec
> module_register_init: MOD_LOAD (amr_linux, 
> 0xffffffff8062a040, 0) error 6
> 
> \***
> !!**
> I have the following hard drives installed.
> 
> Western Digital WD2000JD in Physical location A is SATA but 
> does not seem to be recognized. Is connected via SATA Bus 2 
> on motherboard.
> ad0 is a Western Digital WD2000JB-00KFA0 08.05J08 Physical 
> Location B is IDE ata-0master UDMA100. Is connected via IDE1 
> on motherboard.
> ad4 is a Seagate ST3160827AS 3.42 recognized as ata2 -master 
> SATA150.Is connected via SATA Bus 1 on motherboard.
> acd0 is a CDRW <LITE-ON CD-RW SOHR-5239S/2s03> at ata0-slave 
> UDMA33. Is connected via IDE1 on motherboard.
> I cannot understand why the WD2000JD is not recognized.
> **!!
> ad0: 190781MB <WDC WD2000JB-00KFA0 08.05J08> at ata0-master UDMA100
> acd0: CDRW <LITE-ON CD-RW SOHR-5239S/2S03> at ata0-slave UDMA33
> ad4: 152627MB <Seagate ST3160827AS 3.42> at ata2-master SATA150
> ***\
> da0 at umass-sim0 bus 0 target 0 lun 0
> da0: <USB2.0 CF  CardReader > Removable Direct Access SCSI-0 device 
> da0: 40.000MB/s transfers
> da0: Attempt to query device size failed: NOT READY, Medium 
> not present
> da1 at umass-sim0 bus 0 target 0 lun 1
> da1: <USB2.0 CBO CardReader > Removable Direct Access SCSI-0 device 
> da1: 40.000MB/s transfers
> da1: Attempt to query device size failed: NOT READY, Medium 
> not present
> (da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 
> (da0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
> (da0:umass-sim0:0:0:0): SCSI Status: Check Condition
> (da0:umass-sim0:0:0:0): NOT READY asc:3a,0
> (da0:umass-sim0:0:0:0): Medium not present
> (da0:umass-sim0:0:0:0): Unretryable error
> Opened disk da0 -> 6
> (da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 
> (da0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
> (da0:umass-sim0:0:0:0): SCSI Status: Check Condition
> (da0:umass-sim0:0:0:0): NOT READY asc:3a,0
> (da0:umass-sim0:0:0:0): Medium not present
> (da0:umass-sim0:0:0:0): Unretryable error
> Opened disk da0 -> 6
> (da0:umass-sim0:0:0:0): READ CAPACITY. CDB: 25 0 0 0 0 0 0 0 0 0 
> (da0:umass-sim0:0:0:0): CAM Status: SCSI Status Error
> (da0:umass-sim0:0:0:0): SCSI Status: Check Condition
> (da0:umass-sim0:0:0:0): NOT READY asc:3a,0
> (da0:umass-sim0:0:0:0): Medium not present
> (da0:umass-sim0:0:0:0): Unretryable error
> Opened disk da0 -> 6
> (da1:umass-sim0:0:0:1): READ CAPACITY. CDB: 25 20 0 0 0 0 0 0 0 0 
> (da1:umass-sim0:0:0:1): CAM Status: SCSI Status Error
> (da1:umass-sim0:0:0:1): SCSI Status: Check Condition
> (da1:umass-sim0:0:0:1): NOT READY asc:3a,0
> (da1:umass-sim0:0:0:1): Medium not present
> (da1:umass-sim0:0:0:1): Unretryable error
> Opened disk da1 -> 6
> (da1:umass-sim0:0:0:1): READ CAPACITY. CDB: 25 20 0 0 0 0 0 0 0 0 
> (da1:umass-sim0:0:0:1): CAM Status: SCSI Status Error
> (da1:umass-sim0:0:0:1): SCSI Status: Check Condition
> (da1:umass-sim0:0:0:1): NOT READY asc:3a,0
> (da1:umass-sim0:0:0:1): Medium not present
> (da1:umass-sim0:0:0:1): Unretryable error
> Opened disk da1 -> 6
> (da1:umass-sim0:0:0:1): READ CAPACITY. CDB: 25 20 0 0 0 0 0 0 0 0 
> (da1:umass-sim0:0:0:1): CAM Status: SCSI Status Error
> (da1:umass-sim0:0:0:1): SCSI Status: Check Condition
> (da1:umass-sim0:0:0:1): NOT READY asc:3a,0
> (da1:umass-sim0:0:0:1): Medium not present
> (da1:umass-sim0:0:0:1): Unretryable error
> Opened disk da1 -> 6
> Trying to mount root from ufs:/dev/ad0s1a
> dragon_saver: the console does not support M_VGA_CG320
> module_register_init: MOD_LOAD (dragon_saver, 
> 0xffffffffb39ab540, 0) error 19
> \***
> !!** What is happening here??
> 
> pid 12388 (java), uid 0: exited on signal 6 (core dumped)
> pid 40561 (java), uid 0: exited on signal 6 (core dumped)
> pid 40557 (java), uid 0: exited on signal 6 (core dumped)
> pid 40559 (java), uid 0: exited on signal 6 (core dumped)
> pid 40560 (java), uid 0: exited on signal 6 (core dumped)
> pid 40556 (java), uid 0: exited on signal 6 (core dumped)
> pid 40558 (java), uid 0: exited on signal 6 (core dumped)
> pid 66743 (javac), uid 0: exited on signal 6 (core dumped)
> pid 99229 (conftest), uid 0: exited on signal 12 (core dumped)
> ***\
> 

Just thought to give a fuller picture I should add, in relation to the drive recognition problem, that the CMOS setup utility reports:
CMOS reports
IDE Channel 0 Master WDC WD2000JB 
IDE Channel 0 Slave  LITE-ON CD-RW SOHR
IDE Channel 1Master [None] 
IDE Channel 1 Slave  [None]
IDE Channel 2 Master  [None]  
IDE Channel 3 Master  WDC WD2000JD
IDE Channel 4 Master  [None]
IDE Channel 5 Master  ST3160827As