Tyan S2885 Thunder K8W lockups

[NAKATA Maho]

In Message-ID: <20050727.154329.71086249.chat95 at mac.com> 
NAKATA Maho <chat95 at mac.com> wrote:

> Hello
> sometimes my opteron box locks up recently,
> it seems that there are some discussion about this issue
> on the list.
> 
> o Opteron 250x2
> o Tyan S2885 K8W
>   on board SATA/IEEE1394/USB2/GbE/AC97
> o Total 10G of ram (512Mx4+2Gx4) : tested with memtest+ 1.6
> o BIOS 06/10/05 TYAN  Thunder K8W (S2885) V2.05
> o FreeBSD 5.4-RELEASE
> 
> How to lockup:
> # dd if=/dev/mem of=/dev/null bs=1024k
> about 50 seconds later it lockups. 100% reproducible.
> * Both Optimal/Failsafe setting in BIOS
> * Both MTRR Mapping Continuous/Disabled
> * set hw.physmem="4G" doesn't help
> 
> workaround:
> on board GbE (bge0) and SATA disabled.
dmseg is following:
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.4-RELEASE-p5 #0: Wed Jul 27 16:56:23 JST 2005
    maho at ligeti.private.org:/usr/src/sys/amd64/compile/MAHO
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Opteron(tm) Processor 250 (2390.29-MHz K8-class CPU)
  Origin = "AuthenticAMD"  Id = 0xf5a  Stepping = 10
  Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
  AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow>
real memory  = 10737418240 (10240 MB)
avail memory = 10014359552 (9550 MB)
ACPI APIC Table: <A M I  OEMAPIC >
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
 cpu0 (BSP): APIC ID:  0
 cpu1 (AP): APIC ID:  1
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 <Version 1.1> irqs 0-23 on motherboard
ioapic1 <Version 1.1> irqs 24-27 on motherboard
ioapic2 <Version 1.1> irqs 28-31 on motherboard
acpi0: <A M I OEMXSDT> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x5008-0x500b on acpi0
cpu0: <ACPI CPU> on acpi0
acpi_throttle0: <ACPI CPU Throttling> on cpu0
cpu1: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci1: <ACPI PCI bus> on pcib1
ohci0: <OHCI (generic) USB controller> mem 0xfd7fe000-0xfd7fefff irq 19 at device 0.0 on pci1
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xfd7ff000-0xfd7fffff irq 19 at device 0.1 on pci1
usb1: OHCI version 1.0, legacy support
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
pci1: <serial bus, FireWire> at device 12.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AMD 8111 UDMA133 controller> port 0xffa0-0xffaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
pci0: <serial bus, SMBus> at device 7.2 (no driver attached)
pci0: <bridge> at device 7.3 (no driver attached)
pci0: <multimedia, audio> at device 7.5 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pci2: <ACPI PCI bus> on pcib2
bge0: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem 0xfd8f0000-0xfd8fffff irq 24 at device 9.0 on pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bge0: Ethernet address: 00:e0:81:27:a0:33
pci0: <base peripheral, interrupt controller> at device 10.1 (no driver attached)
pcib3: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pci3: <ACPI PCI bus> on pcib3
pci0: <base peripheral, interrupt controller> at device 11.1 (no driver attached)
pcib4: <ACPI Host-PCI bridge> on acpi0
pci4: <ACPI PCI bus> on pcib4
pcib5: <ACPI PCI-PCI bridge> at device 1.0 on pci4
pci5: <ACPI PCI bus> on pcib5
pci5: <display, VGA> at device 0.0 (no driver attached)
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse Explorer, device ID 4
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
fdc0: <floppy drive controller (FDE)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
ppc0: <Standard parallel printer port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
orm0: <ISA Option ROM> at iomem 0xc0000-0xc8fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
ad0: 117800MB <HDS722512VLAT80/V33OA60A> [239340/16/63] at ata0-master UDMA100
acd0: DVDR <PIONEER DVD-RW DVR-106D/1.06> at ata1-master UDMA33
SMP: AP CPU #1 Launched!
cd0 at ata1 bus 0 target 0 lun 0
cd0: <PIONEER DVD-RW  DVR-106D 1.06> Removable CD-ROM SCSI-0 device
cd0: 33.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
Mounting root from ufs:/dev/ad0s1a