Adaptec AIC-7902W can not use 320M/s Sync Transfer Rate.
DIrk
archive.it at gmail.com
Thu Jan 20 19:32:51 PST 2005
I have a AMD64 server :
Thunder K8S Pro (S2882)
Opteron 246 x2
1G x4 RAM
Seagate ST3146707LW x2
FreeBSD/amd64 5.3 stable
Mobo BIOS: 2.04
Adaptec BIOS: 4.30
NO ANY RAID CARD used.
At first, I use the SCSI U320 mode, FreeBSD complained about "DUMP
CARD STATE" at booting & disk io sometimes.
And it is working fine when I set SCSI to U160 mode (Step down the
"Sync Transfer Rate" from 320M/s to 160M/s).
Is here some problem with the SCSI cable or terminator ?
Any suggestion ?
Thanks very much.
Here is system Uname:
FreeBSD www.test.com 5.3-STABLE FreeBSD 5.3-STABLE #0: Thu Jan 20
22:47:43 CST 2005 root at www.test.com:/usr/obj/usr/src/sys/THENORA
amd64
Here is error dmesg under U320 mode:
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.3-STABLE #0: Thu Jan 20 22:47:43 CST 2005
root at www.test.com:/usr/obj/usr/src/sys/THENORA
WARNING: debug.mpsafenet forced to 0 as ipsec requires Giant
WARNING: MPSAFE network stack disabled, expect reduced performance.
ACPI APIC Table: <A M I OEMAPIC >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Opteron(tm) Processor 246 (1995.40-MHz K8-class CPU)
Origin = "AuthenticAMD" Id = 0xf58 Stepping = 8
Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow>
real memory = 4227792896 (4031 MB)
avail memory = 4083990528 (3894 MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 <Version 1.1> irqs 0-23 on motherboard
ioapic1 <Version 1.1> irqs 24-27 on motherboard
ioapic2 <Version 1.1> irqs 28-31 on motherboard
acpi0: <A M I OEMRSDT> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x5008-0x500b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci3: <ACPI PCI bus> on pcib1
pci3: <display, VGA> at device 6.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AMD 8111 UDMA133 controller> port
0xffa0-0xffaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on
pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
pci0: <serial bus, SMBus> at device 7.2 (no driver attached)
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pci2: <ACPI PCI bus> on pcib2
ahd0: <Adaptec AIC7902 Ultra320 SCSI adapter> port
0xac00-0xacff,0xa000-0xa0ff mem 0xfc8fc000-0xfc8fdfff irq 24 at device
6.0 on pci2
ahd0: [GIANT-LOCKED]
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
ahd1: <Adaptec AIC7902 Ultra320 SCSI adapter> port
0xa400-0xa4ff,0xa800-0xa8ff mem 0xfc8fe000-0xfc8fffff irq 25 at device
6.1 on pci2
ahd1: [GIANT-LOCKED]
aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
bge0: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2003> mem
0xfc9b0000-0xfc9bffff,0xfc9c0000-0xfc9cffff irq 24 at device 9.0 on
pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5704 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge0: Ethernet address: 00:e0:81:2b:a5:62
bge0: [GIANT-LOCKED]
bge1: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2003> mem
0xfc9e0000-0xfc9effff,0xfc9f0000-0xfc9fffff irq 25 at device 9.1 on
pci2
miibus1: <MII bus> on bge1
brgphy1: <BCM5704 10/100/1000baseTX PHY> on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge1: Ethernet address: 00:e0:81:2b:a5:63
bge1: [GIANT-LOCKED]
pci0: <base peripheral, interrupt controller> at device 10.1 (no
driver attached)
pcib3: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pci1: <ACPI PCI bus> on pcib3
pci0: <base peripheral, interrupt controller> at device 11.1 (no
driver attached)
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
orm0: <ISA Option ROM> at iomem 0xc0000-0xc7fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.35 initialized. Default = block all, Logging = enabled
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
acd0: CDROM <MSI CD-ROM 52X/52LPM> at ata0-master UDMA33
Waiting 5 seconds for SCSI devices to settle
ahd0: Invalid Sequencer interrupt occurred.
>>>>>>>>>>>>>>>>>> Dump Card State Begins <<<<<<<<<<<<<<<<<
ahd0: Dumping Card State at program address 0x23c Mode 0x0
Card was paused
INTSTAT[0x0] SELOID[0x1] SELID[0x0] HS_MAILBOX[0x0]
INTCTL[0x80] SEQINTSTAT[0x0] SAVED_MODE[0x11] DFFSTAT[0x33]
SCSISIGI[0x0] SCSIPHASE[0x0] SCSIBUS[0x0] LASTPHASE[0x1]
SCSISEQ0[0x0] SCSISEQ1[0x12] SEQCTL0[0x0] SEQINTCTL[0x6]
SEQ_FLAGS[0x0] SEQ_FLAGS2[0x0] QFREEZE_COUNT[0x2]
KERNEL_QFREEZE_COUNT[0x2] MK_MESSAGE_SCB[0xff00] MK_MESSAGE_SCSIID[0xff]
SSTAT0[0x0] SSTAT1[0x8] SSTAT2[0x0] SSTAT3[0x0] PERRDIAG[0x0]
SIMODE1[0xa4] LQISTAT0[0x0] LQISTAT1[0x0] LQISTAT2[0x0]
LQOSTAT0[0x0] LQOSTAT1[0x0] LQOSTAT2[0x0]
SCB Count = 16 CMDS_PENDING = 0 LASTSCB 0xffff CURRSCB 0xe NEXTSCB 0xff40
qinstart = 28 qinfifonext = 28
QINFIFO:
WAITING_TID_QUEUES:
Pending list:
Total 0
Kernel Free SCB list: 15 14 1 2 3 4 5 6 7 8 9 10 11 12 13 0
Sequencer Complete DMA-inprog list:
Sequencer Complete list:
Sequencer DMA-Up and Complete list:
Sequencer On QFreeze and Complete list:
ahd0: FIFO0 Free, LONGJMP == 0x8000, SCB 0xf
SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]
SG_CACHE_SHADOW[0x2] SG_STATE[0x0] DFFSXFRCTL[0x0]
SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR = 0x00, SHCNT = 0x0
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
ahd0: FIFO1 Free, LONGJMP == 0x8063, SCB 0xe
SEQIMODE[0x3f] SEQINTSRC[0x0] DFCNTRL[0x0] DFSTATUS[0x89]
SG_CACHE_SHADOW[0x2] SG_STATE[0x0] DFFSXFRCTL[0x0]
SOFFCNT[0x0] MDFFSTAT[0x5] SHADDR = 0x00, SHCNT = 0x0
HADDR = 0x00, HCNT = 0x0 CCSGCTL[0x10]
LQIN: 0x8 0x0 0x0 0xf 0x0 0x1 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0 0x0
0x0 0x0 0x0 0x0
ahd0: LQISTATE = 0x0, LQOSTATE = 0x0, OPTIONMODE = 0x42
ahd0: OS_SPACE_CNT = 0x20 MAXCMDCNT = 0x1
ahd0: SAVED_SCSIID = 0x0 SAVED_LUN = 0x0
SIMODE0[0xc]
CCSCBCTL[0x4]
ahd0: REG0 == 0x563e, SINDEX = 0x10e, DINDEX = 0x104
ahd0: SCBPTR == 0xf, SCB_NEXT == 0xff40, SCB_NEXT2 == 0xff9b
CDB 12 20 0 80 88 a6
STACK: 0x237 0x2 0x0 0x0 0x0 0x0 0x0 0x0
<<<<<<<<<<<<<<<<< Dump Card State Ends >>>>>>>>>>>>>>>>>>
Copied 18 bytes of sense data offset 12: 0x70 0x0 0x6 0x0 0x0 0x0 0x0
0xa 0x0 0x0 0x0 0x0 0x29 0x2 0x2 0x0 0x0 0x0
Copied 18 bytes of sense data offset 12: 0x70 0x0 0x6 0x0 0x0 0x0 0x0
0xa 0x0 0x0 0x0 0x0 0x29 0x2 0x2 0x0 0x0 0x0
SMP: AP CPU #1 Launched!
da0 at ahd0 bus 0 target 0 lun 0
da0: <SEAGATE ST3146707LW D701> Fixed Direct Access SCSI-3 device
da0: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged
Queueing Enabled
da0: 140014MB (286749480 512 byte sectors: 255H 63S/T 17849C)
da1 at ahd0 bus 0 target 1 lun 0
da1: <SEAGATE ST3146707LW D701> Fixed Direct Access SCSI-3 device
da1: 320.000MB/s transfers (160.000MHz, offset 63, 16bit), Tagged
Queueing Enabled
da1: 140014MB (286749480 512 byte sectors: 255H 63S/T 17849C)
Mounting root from ufs:/dev/da0s1a
And no problem dmesg under U160:
Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
The Regents of the University of California. All rights reserved.
FreeBSD 5.3-STABLE #0: Thu Jan 20 22:47:43 CST 2005
root at www.test.com:/usr/obj/usr/src/sys/THENORA
WARNING: debug.mpsafenet forced to 0 as ipsec requires Giant
WARNING: MPSAFE network stack disabled, expect reduced performance.
ACPI APIC Table: <A M I OEMAPIC >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: AMD Opteron(tm) Processor 246 (1995.49-MHz K8-class CPU)
Origin = "AuthenticAMD" Id = 0xf58 Stepping = 8
Features=0x78bfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,MMX,FXSR,SSE,SSE2>
AMD Features=0xe0500800<SYSCALL,NX,MMX+,LM,3DNow+,3DNow>
real memory = 4227792896 (4031 MB)
avail memory = 4083990528 (3894 MB)
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
cpu0 (BSP): APIC ID: 0
cpu1 (AP): APIC ID: 1
MADT: Forcing active-low polarity and level trigger for SCI
ioapic0 <Version 1.1> irqs 0-23 on motherboard
ioapic1 <Version 1.1> irqs 24-27 on motherboard
ioapic2 <Version 1.1> irqs 28-31 on motherboard
acpi0: <A M I OEMRSDT> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x5008-0x500b on acpi0
cpu0: <ACPI CPU> on acpi0
cpu1: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pci3: <ACPI PCI bus> on pcib1
pci3: <display, VGA> at device 6.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <AMD 8111 UDMA133 controller> port
0xffa0-0xffaf,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 7.1 on
pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
pci0: <serial bus, SMBus> at device 7.2 (no driver attached)
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pci2: <ACPI PCI bus> on pcib2
ahd0: <Adaptec AIC7902 Ultra320 SCSI adapter> port
0xac00-0xacff,0xa000-0xa0ff mem 0xfc8fc000-0xfc8fdfff irq 24 at device
6.0 on pci2
ahd0: [GIANT-LOCKED]
aic7902: Ultra320 Wide Channel A, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
ahd1: <Adaptec AIC7902 Ultra320 SCSI adapter> port
0xa400-0xa4ff,0xa800-0xa8ff mem 0xfc8fe000-0xfc8fffff irq 25 at device
6.1 on pci2
ahd1: [GIANT-LOCKED]
aic7902: Ultra320 Wide Channel B, SCSI Id=7, PCI-X 67-100Mhz, 512 SCBs
bge0: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2003> mem
0xfc9b0000-0xfc9bffff,0xfc9c0000-0xfc9cffff irq 24 at device 9.0 on
pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5704 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge0: Ethernet address: 00:e0:81:2b:a5:62
bge0: [GIANT-LOCKED]
bge1: <Broadcom BCM5704C Dual Gigabit Ethernet, ASIC rev. 0x2003> mem
0xfc9e0000-0xfc9effff,0xfc9f0000-0xfc9fffff irq 25 at device 9.1 on
pci2
miibus1: <MII bus> on bge1
brgphy1: <BCM5704 10/100/1000baseTX PHY> on miibus1
brgphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge1: Ethernet address: 00:e0:81:2b:a5:63
bge1: [GIANT-LOCKED]
pci0: <base peripheral, interrupt controller> at device 10.1 (no
driver attached)
pcib3: <ACPI PCI-PCI bridge> at device 11.0 on pci0
pci1: <ACPI PCI bus> on pcib3
pci0: <base peripheral, interrupt controller> at device 11.1 (no
driver attached)
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
orm0: <ISA Option ROM> at iomem 0xc0000-0xc7fff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
IPsec: Initialized Security Association Processing.
IP Filter: v3.4.35 initialized. Default = block all, Logging = enabled
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
acd0: CDROM <MSI CD-ROM 52X/52LPM> at ata0-master UDMA33
Waiting 5 seconds for SCSI devices to settle
SMP: AP CPU #1 Launched!
da0 at ahd0 bus 0 target 0 lun 0
da0: <SEAGATE ST3146707LW D701> Fixed Direct Access SCSI-3 device
da0: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged
Queueing Enabled
da0: 140014MB (286749480 512 byte sectors: 255H 63S/T 17849C)
da1 at ahd0 bus 0 target 1 lun 0
da1: <SEAGATE ST3146707LW D701> Fixed Direct Access SCSI-3 device
da1: 160.000MB/s transfers (80.000MHz, offset 63, 16bit), Tagged
Queueing Enabled
da1: 140014MB (286749480 512 byte sectors: 255H 63S/T 17849C)
Mounting root from ufs:/dev/da0s1a
More information about the freebsd-amd64
mailing list