continuing troubles with AMD64
Mikhail Teterin
mi+mx at aldan.algebra.com
Wed Jun 9 02:43:34 GMT 2004
The good part: the Mar 1st -current kernel works fine.
The bad:
1) Any newer kernels don't see the system drive, presumably,
abecause ttempts to allocate IRQs for the all of the
aata-controllers fail.
2) Yesterday's kernel panics with:
madt_probe_cpus_handler: CPU ID 129 too high
Indeed, 129 is greater than NLAPICS, which is 32, but the
Mar 1st kernel works.
We can work around the second problem by disabling the APIC in the BIOS,
or by disabling the ACPI altogether on the loader's prompt.
We did not yet find the workaround for 1), however. All of the
ata-controllers and some other hardware (like firewire) report "unable
to allocate IRQ" with any of the more recent kernels.
I'm attaching the dmesg.boot, as obtained with the Mar 1st kernel. Please,
advise. Thanks!
-mi
-------------- next part --------------
ioapic0: intpin 7 -> irq 7 (edge, activehi)
ioapic0: intpin 8 -> irq 8 (edge, activehi)
ioapic0: intpin 9 -> irq 9 (edge, activehi)
ioapic0: intpin 10 -> irq 10 (edge, activehi)
ioapic0: intpin 11 -> irq 11 (edge, activehi)
ioapic0: intpin 12 -> irq 12 (edge, activehi)
ioapic0: intpin 13 -> irq 13 (edge, activehi)
ioapic0: intpin 14 -> irq 14 (edge, activehi)
ioapic0: intpin 15 -> irq 15 (edge, activehi)
ioapic0: intpin 16 -> irq 16 (level, activelo)
ioapic0: intpin 17 -> irq 17 (level, activelo)
ioapic0: intpin 18 -> irq 18 (level, activelo)
ioapic0: intpin 19 -> irq 19 (level, activelo)
ioapic0: intpin 20 -> irq 20 (level, activelo)
ioapic0: intpin 21 -> irq 21 (level, activelo)
ioapic0: intpin 22 -> irq 22 (level, activelo)
ioapic0: intpin 23 -> irq 23 (level, activelo)
MADT: Found IO APIC ID 2, Interrupt 24 at 0xff4fe000
ioapic1: intpin 0 -> irq 24 (level, activelo)
ioapic1: intpin 1 -> irq 25 (level, activelo)
ioapic1: intpin 2 -> irq 26 (level, activelo)
ioapic1: intpin 3 -> irq 27 (level, activelo)
MADT: Found IO APIC ID 3, Interrupt 28 at 0xff4ff000
ioapic2: intpin 0 -> irq 28 (level, activelo)
ioapic2: intpin 1 -> irq 29 (level, activelo)
ioapic2: intpin 2 -> irq 30 (level, activelo)
ioapic2: intpin 3 -> irq 31 (level, activelo)
MADT: intr override: source 0, irq 2
ioapic0: Routing IRQ 0 -> intpin 2
ioapic0: intpin 2 polarity: active-hi
ioapic0: intpin 2 trigger: edge
ioapic0 <Version 1.1> irqs 0-23 on motherboard
ioapic1 <Version 1.1> irqs 24-27 on motherboard
ioapic2 <Version 1.1> irqs 28-31 on motherboard
cpu0 BSP:
ID: 0x00000000 VER: 0x00040010 LDR: 0x01000000 DFR: 0x0fffffff
lint0: 0x00010700 lint1: 0x00000400 TPR: 0x00000000 SVR: 0x000001ff
random: <entropy source>
mem: <memory & I/O>
null: <null device, zero device>
acpi0: <A M I OEMXSDT> on motherboard
pci_open(1): mode 1 addr port (0x0cf8) is 0x800358b0
pci_open(1a): mode1res=0x80000000 (0x80000000)
pci_cfgcheck: device 0 1 2 3 4 5 6 [class=060400] [hdr=01] is there (id=74601022)
AcpiOsDerivePciId: bus 0 dev 7 func 0
AcpiOsDerivePciId: bus 0 dev 7 func 1
AcpiOsDerivePciId: bus 0 dev 7 func 3
acpi0: Power Button (fixed)
AcpiOsDerivePciId: bus 0 dev 10 func 0
AcpiOsDerivePciId: bus 0 dev 11 func 0
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
ACPI timer looks GOOD min = 3, max = 4, width = 1
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x5008-0x500b on acpi0
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
acpi_cpu0: <CPU> port 0x530-0x537 on acpi0
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
acpi_cpu1: <CPU> port 0x530-0x537 on acpi0
device_probe_and_attach: acpi_cpu1 attach returned 6
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci0: <ACPI PCI bus> on pcib0
pci0: physical bus=0
found-> vendor=0x1022, dev=0x7460, revid=0x07
bus=0, slot=6, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0117, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x07 (1750 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x7468, revid=0x05
bus=0, slot=7, func=0
class=06-01-00, hdrtype=0x00, mfdev=1
cmdreg=0x000f, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[20]: type 4, range 32, base 0000ffa0, size 4, enabled
found-> vendor=0x1022, dev=0x7469, revid=0x03
bus=0, slot=7, func=1
class=01-01-8a, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x20 (960 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 4, range 32, base 0000a480, size 5, enabled
pcib0: matched entry for 0.7.INTD (source )
pcib0: device is hardwired to IRQ 19
found-> vendor=0x1022, dev=0x746a, revid=0x02
bus=0, slot=7, func=2
class=0c-05-00, hdrtype=0x00, mfdev=0
cmdreg=0x0001, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=d, irq=19
found-> vendor=0x1022, dev=0x746b, revid=0x05
bus=0, slot=7, func=3
class=06-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0000, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 4, range 32, base 0000a800, size 8, enabled
map[14]: type 4, range 32, base 0000ac00, size 6, enabled
pcib0: matched entry for 0.7.INTB (source )
pcib0: device is hardwired to IRQ 17
found-> vendor=0x1022, dev=0x746d, revid=0x03
bus=0, slot=7, func=5
class=04-01-00, hdrtype=0x00, mfdev=0
cmdreg=0x0005, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=b, irq=17
found-> vendor=0x1022, dev=0x7450, revid=0x12
bus=0, slot=10, func=0
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0116, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x05 (1250 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 64, base ff4fe000, size 12, enabled
found-> vendor=0x1022, dev=0x7451, revid=0x01
bus=0, slot=10, func=1
class=08-00-10, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
map[10]: type 1, range 64, base 00000000, size 12, enabled
found-> vendor=0x1022, dev=0x7450, revid=0x12
bus=0, slot=11, func=0
class=06-04-00, hdrtype=0x01, mfdev=1
cmdreg=0x0116, statreg=0x0230, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x05 (1250 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
map[10]: type 1, range 64, base ff4ff000, size 12, enabled
found-> vendor=0x1022, dev=0x7451, revid=0x01
bus=0, slot=11, func=1
class=08-00-10, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0200, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1100, revid=0x00
bus=0, slot=24, func=0
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0010, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1101, revid=0x00
bus=0, slot=24, func=1
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1102, revid=0x00
bus=0, slot=24, func=2
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x1103, revid=0x00
bus=0, slot=24, func=3
class=06-00-00, hdrtype=0x00, mfdev=1
cmdreg=0x0000, statreg=0x0000, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
pcib1: <ACPI PCI-PCI bridge> at device 6.0 on pci0
pcib1: secondary bus 3
pcib1: subordinate bus 3
pcib1: I/O decode 0x8000-0x8fff
pcib1: memory decode 0xff200000-0xff3fffff
pcib1: prefetched decode 0xe6800000-0xe68fffff
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci3: <ACPI PCI bus> on pcib1
pci3: physical bus=3
map[10]: type 1, range 32, base ff3fc000, size 12, enabled
pcib1: matched entry for 3.0.INTD (source )
pcib1: device is hardwired to IRQ 19
found-> vendor=0x1022, dev=0x7464, revid=0x0b
bus=3, slot=0, func=0
class=0c-03-10, hdrtype=0x00, mfdev=1
cmdreg=0x0117, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
intpin=d, irq=19
map[10]: type 1, range 32, base ff3fd000, size 12, enabled
pcib1: matched entry for 3.0.INTD (source )
pcib1: device is hardwired to IRQ 19
found-> vendor=0x1022, dev=0x7464, revid=0x0b
bus=3, slot=0, func=1
class=0c-03-10, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0280, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x50 (20000 ns)
intpin=d, irq=19
map[10]: type 4, range 32, base 00008000, size 8, enabled
map[14]: type 1, range 32, base ff3fe000, size 12, enabled
pcib1: matched entry for 3.10.INTA (source )
pcib1: device is hardwired to IRQ 16
found-> vendor=0x9004, dev=0x8178, revid=0x00
bus=3, slot=10, func=0
class=01-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0117, statreg=0x0280, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x08 (2000 ns)
intpin=a, irq=16
map[10]: type 4, range 32, base 00008c00, size 3, enabled
map[14]: type 4, range 32, base 00008880, size 2, enabled
map[18]: type 4, range 32, base 00008800, size 3, enabled
map[1c]: type 4, range 32, base 00008480, size 2, enabled
map[20]: type 4, range 32, base 00008400, size 4, enabled
map[24]: type 1, range 32, base ff3ffc00, size 10, enabled
pcib1: matched entry for 3.11.INTA (source )
pcib1: device is hardwired to IRQ 17
found-> vendor=0x1095, dev=0x3114, revid=0x02
bus=3, slot=11, func=0
class=01-80-00, hdrtype=0x00, mfdev=0
cmdreg=0x0107, statreg=0x02b0, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=17
powerspec 2 supports D0 D1 D2 D3 current D0
ohci0: <OHCI (generic) USB controller> mem 0xff3fc000-0xff3fcfff irq 19 at device 0.0 on pci3
pcib1: device ohci0 requested decoded memory range 0xff3fc000-0xff3fcfff
usb0: OHCI version 1.0, legacy support
usb0: <OHCI (generic) USB controller> on ohci0
usb0: USB revision 1.0
uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 3 ports with 3 removable, self powered
ohci1: <OHCI (generic) USB controller> mem 0xff3fd000-0xff3fdfff irq 19 at device 0.1 on pci3
pcib1: device ohci1 requested decoded memory range 0xff3fd000-0xff3fdfff
usb1: OHCI version 1.0, legacy support
usb1: <OHCI (generic) USB controller> on ohci1
usb1: USB revision 1.0
uhub1: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 3 ports with 3 removable, self powered
ahc0: <Adaptec 2940 Ultra SCSI adapter> port 0x8000-0x80ff mem 0xff3fe000-0xff3fefff irq 16 at device 10.0 on pci3
ahc0: Defaulting to MEMIO off
pcib1: device ahc0 requested decoded I/O range 0x8000-0x80ff
ahc0: Enabling 39Bit Addressing
ahc0: Reading SEEPROM...done.
ahc0: internal 50 cable not present, internal 68 cable is present
ahc0: external cable not present
ahc0: BIOS eeprom is present
ahc0: High byte termination Enabled
ahc0: Low byte termination Enabled
ahc0: Downloading Sequencer Program... 457 instructions downloaded
ahc0: Features 0x10005, Bugs 0x25, Flags 0x21401540
aic7880: Ultra Wide Channel A, SCSI Id=7, 16/253 SCBs
atapci0: <SiI 3114 SATA150 controller> port 0x8400-0x840f,0x8480-0x8483,0x8800-0x8807,0x8880-0x8883,0x8c00-0x8c07 mem 0xff3ffc00-0xff3fffff irq 17 at device 11.0 on pci3
pcib1: device atapci0 requested decoded I/O range 0x8400-0x840f
atapci0: [MPSAFE]
pcib1: device atapci0 requested decoded memory range 0xff3ffc00-0xff3fffff
ata2: reset tp1 mask=01 ostat0=50 ostat1=50
ata2-master: stat=0x50 err=0x01 lsb=0x00 msb=0x00
ata2: reset tp2 mask=01 stat0=50 stat1=00 devices=0x1<ATA_MASTER>
ata2: at 0xff3ffc00 on atapci0
ata2: [MPSAFE]
ata3: reset tp1 mask=01 ostat0=7f ostat1=7f
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3-master: stat=0x7f err=0x00 lsb=0x00 msb=0x00
ata3: reset tp2 mask=00 stat0=ff stat1=00 devices=0x0
ata3: at 0xff3ffc00 on atapci0
ata3: [MPSAFE]
ata4: at 0xff3ffc00 on atapci0
ata4: [MPSAFE]
ata5: at 0xff3ffc00 on atapci0
ata5: [MPSAFE]
isab0: <PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <AMD 8111 UDMA133 controller> port 0xffa0-0xffaf at device 7.1 on pci0
ata0: reset tp1 mask=03 ostat0=50 ostat1=00
ata0-master: stat=0x00 err=0x01 lsb=0x14 msb=0xeb
ata0-slave: stat=0x00 err=0x00 lsb=0x14 msb=0xeb
ata0: reset tp2 mask=03 stat0=00 stat1=00 devices=0x4<ATAPI_MASTER>
ata0: at 0x1f0 irq 14 on atapci1
ata0: [MPSAFE]
ata1: reset tp1 mask=03 ostat0=50 ostat1=7f
ata1-master: stat=0x10 err=0x01 lsb=0x14 msb=0xeb
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1-slave: stat=0x7f err=0x7f lsb=0x7f msb=0x7f
ata1: reset tp2 mask=01 stat0=10 stat1=ff devices=0x4<ATAPI_MASTER>
ata1: at 0x170 irq 15 on atapci1
ata1: [MPSAFE]
pci0: <serial bus, SMBus> at device 7.2 (no driver attached)
pci0: <bridge, PCI-unknown> at device 7.3 (no driver attached)
pcm0: <AMD-8111> port 0xac00-0xac3f,0xa800-0xa8ff irq 17 at device 7.5 on pci0
pcm0: <Analog Devices AD1981B AC97 Codec (id = 0x41445374)>
pcm0: Codec features headphone, 20 bit DAC, 5 bit master volume, no 3D Stereo Enhancement
pcm0: Primary codec extended features variable rate PCM, reserved 1, AMAP, reserved 4
pcm0: sndbuf_setmap a8b000, 4000; 0xffffffffb60c7000 -> a8b000
pcm0: sndbuf_setmap a91000, 4000; 0xffffffffb60cb000 -> a91000
pcib2: <ACPI PCI-PCI bridge> at device 10.0 on pci0
pcib2: secondary bus 2
pcib2: subordinate bus 2
pcib2: I/O decode 0x0-0x0
pcib2: memory decode 0xff100000-0xff1fffff
pcib2: prefetched decode 0xe6700000-0xe67fffff
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci2: <ACPI PCI bus> on pcib2
pci2: physical bus=2
map[10]: type 3, range 32, base e67f0000, size 16, enabled
pcib2: matched entry for 2.7.INTA (source )
pcib2: device is hardwired to IRQ 26
found-> vendor=0x1000, dev=0x1960, revid=0x01
bus=2, slot=7, func=0
class=01-04-00, hdrtype=0x00, mfdev=0
cmdreg=0x0116, statreg=0x04b0, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
intpin=a, irq=26
powerspec 2 supports D0 D3 current D0
map[10]: type 1, range 64, base ff1f0000, size 16, enabled
pcib2: matched entry for 2.9.INTA (source )
pcib2: device is hardwired to IRQ 24
found-> vendor=0x14e4, dev=0x16a7, revid=0x02
bus=2, slot=9, func=0
class=02-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0116, statreg=0x02b0, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x40 (16000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=24
powerspec 2 supports D0 D3 current D0
MSI supports 8 messages, 64 bit
amr0: <LSILogic MegaRAID> mem 0xe67f0000-0xe67fffff irq 26 at device 7.0 on pci2
pcib2: device amr0 requested decoded memory range 0xe67f0000-0xe67fffff
amr0: <LSILogic MegaRAID SATA 150-6D> Firmware 712T, BIOS G116, 64MB RAM
bge0: <Broadcom BCM5703 Gigabit Ethernet, ASIC rev. 0x1002> mem 0xff1f0000-0xff1fffff irq 24 at device 9.0 on pci2
pcib2: device bge0 requested decoded memory range 0xff1f0000-0xff1fffff
bge0: Ethernet address: 00:e0:81:28:21:04
miibus0: <MII bus> on bge0
brgphy0: <BCM5703 10/100/1000baseTX PHY> on miibus0
brgphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bge0: bpf attached
pci0: <base peripheral, interrupt controller> at device 10.1 (no driver attached)
pcib3: <ACPI PCI-PCI bridge> mem 0-0xfff at device 11.0 on pci0
pcib3: secondary bus 1
pcib3: subordinate bus 1
pcib3: I/O decode 0x0-0x0
pcib3: memory decode 0xff000000-0xff0fffff
pcib3: prefetched decode 0xe6600000-0xe66fffff
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci1: <ACPI PCI bus> on pcib3
pci1: physical bus=1
pci0: <base peripheral, interrupt controller> at device 11.1 (no driver attached)
pcib4: <ACPI Host-PCI bridge> on acpi0
pcib4: could not get PCI interrupt routing table for \\_SB_.PCIB - AE_NOT_FOUND
pci4: <ACPI PCI bus> on pcib4
pci4: physical bus=4
map[10]: type 3, range 32, base f0000000, size 27, enabled
found-> vendor=0x1022, dev=0x7454, revid=0x13
bus=4, slot=0, func=0
class=06-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0006, statreg=0x0210, cachelnsz=0 (dwords)
lattimer=0x00 (0 ns), mingnt=0x00 (0 ns), maxlat=0x00 (0 ns)
found-> vendor=0x1022, dev=0x7455, revid=0x13
bus=4, slot=1, func=0
class=06-04-00, hdrtype=0x01, mfdev=0
cmdreg=0x0107, statreg=0x0220, cachelnsz=0 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
pcib5: <ACPI PCI-PCI bridge> at device 1.0 on pci4
pcib5: secondary bus 5
pcib5: subordinate bus 5
pcib5: I/O decode 0xb000-0xbfff
pcib5: memory decode 0xff500000-0xff5fffff
pcib5: prefetched decode 0xe6a00000-0xeeafffff
---- initial configuration ------------------------
---- before setting priority for links ------------
---- before fixup boot-disabled links -------------
---- after fixup boot-disabled links --------------
---- arbitrated configuration ---------------------
pci5: <ACPI PCI bus> on pcib5
pci5: physical bus=5
map[10]: type 3, range 32, base e8000000, size 26, enabled
map[14]: type 4, range 32, base 0000b800, size 8, enabled
map[18]: type 1, range 32, base ff5fc000, size 14, enabled
found-> vendor=0x1002, dev=0x5446, revid=0x00
bus=5, slot=0, func=0
class=03-00-00, hdrtype=0x00, mfdev=0
cmdreg=0x0087, statreg=0x02b0, cachelnsz=16 (dwords)
lattimer=0x40 (1920 ns), mingnt=0x08 (2000 ns), maxlat=0x00 (0 ns)
intpin=a, irq=255
powerspec 2 supports D0 D1 D3 current D0
pci5: <display, VGA> at device 0.0 (no driver attached)
acpi_button0: <Power Button> on acpi0
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
atkbd: the current kbd controller command byte 0065
atkbd: keyboard ID 0x41ab (2)
kbd0 at atkbd0
kbd0: atkbd0, AT 101/102 (2), config:0x1, flags:0x3d0000
psm0: unable to allocate IRQ
unknown: not probed (disabled)
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: irq maps: 0 0 0 0
sio0 port 0x3f8-0x3ff irq 4 on acpi0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: irq maps: 0 0 0 0
sio1 port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: using extended I/O port range
ppc0: SPP
ppc0 port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
unknown: not probed (disabled)
unknown: not probed (disabled)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_probe: no address given, try 0x530
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
acpi_cpu1: <CPU> port 0x530-0x537 on acpi0
device_probe_and_attach: acpi_cpu1 attach returned 6
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
unknown: not probed (disabled)
unknown: not probed (disabled)
unknown: not probed (disabled)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
mss_detect, busy still set (0xff)
atkbdc: atkbdc0 already exists; skipping it
fdc: fdc0 already exists; skipping it
ppc: ppc0 already exists; skipping it
sio: sio0 already exists; skipping it
sio: sio1 already exists; skipping it
Trying Read_Port at 203
Trying Read_Port at 243
Trying Read_Port at 283
Trying Read_Port at 2c3
Trying Read_Port at 303
Trying Read_Port at 343
Trying Read_Port at 383
Trying Read_Port at 3c3
sc: sc0 already exists; skipping it
vga: vga0 already exists; skipping it
isa_probe_children: disabling PnP devices
isa_probe_children: probing non-PnP devices
orm0: <Option ROMs> at iomem 0xcd000-0xcd7ff,0xc8000-0xcc7ff,0xc0000-0xc7fff on isa0
pcic0 failed to probe at port 0x3e0 iomem 0xd0000 on isa0
pcic1: not probed (disabled)
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sc0: fb0, kbd0, terminal emulator: sc (syscons terminal)
sio2: not probed (disabled)
sio3: not probed (disabled)
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
fb0: vga0, vga, type:VGA (5), flags:0x7007f
fb0: port:0x3c0-0x3df, crtc:0x3d4, mem:0xa0000 0x20000
fb0: init mode:24, bios mode:3, current mode:24
fb0: window:0xffffffff800b8000 size:32k gran:32k, buf:0 size:32k
VGA parameters upon power-up
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
VGA parameters in BIOS for mode 24
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
EGA/VGA parameters to be used for mode 24
50 18 10 00 00 00 03 00 02 67 5f 4f 50 82 55 81
bf 1f 00 4f 0d 0e 00 00 07 80 9c 8e 8f 28 1f 96
b9 a3 ff 00 01 02 03 04 05 14 07 38 39 3a 3b 3c
3d 3e 3f 0c 00 0f 08 00 00 00 00 00 10 0e 00 ff
isa_probe_children: probing PnP devices
Device configuration finished.
procfs registered
Timecounter "TSC" frequency 1792869156 Hz quality 800
Timecounters tick every 10.000 msec
BRIDGE 031224 loaded
lo0: bpf attached
acpi_cpu0: set speed to 100.0%
acpi_cpu: throttling enabled, 8 steps (100% to 12.5%), currently 100.0%
ata0-master: pio=0x0c wdma=0x22 udma=0xffffffff cable=40pin
ata0-master: setting PIO4 on AMD 8111 chip
acd0: <FX320S/q01> CDROM drive at ata0 as master
acd0: read 5512KB/s (5512KB/s), 256KB buffer, PIO4
acd0: Reads: CDR, CDRW, CDDA, packet
acd0: Writes:
acd0: Audio: play, 255 volume levels
acd0: Mechanism: ejectable tray, unlocked
acd0: Medium: no/blank disc
ata1-master: pio=0x0b wdma=0xffffffff udma=0xffffffff cable=40pin
ata1-master: setting PIO3 on AMD 8111 chip
afd0: <IOMEGA ZIP 100 ATAPI/12.A> removable drive at ata1 as master
afd0: 96MB (196608 sectors), 96 cyls, 64 heads, 32 S/T, 512 B/S
afd0: 4096KB/s, PIO3
GEOM: new disk afd0
ata2-master: pio=0x0c wdma=0x22 udma=0x45 cable=80pin
ad4: <WDC WD2000JD-00FYB0/02.05D02> ATA-6 disk at ata2-master
ad4: 190782MB (390721968 sectors), 387621 C, 16 H, 63 S, 512 B
ad4: 16 secs/int, 1 depth queue, UDMA100
Waiting 15 seconds for SCSI devices to settle
(noperiph:ahc0:0:-1:-1): SCSI bus reset delivered. 0 SCBs aborted.
pcm0: measured ac97 link rate at 48163 Hz, will use 48000 Hz
amrd0: <LSILogic MegaRAID logical drive> on amr0
amrd0: 953885MB (1953556480 sectors) RAID 5 (optimal)
GEOM: new disk ad4
GEOM: new disk amrd0
[0] f:80 typ:165 s(CHS):0/0/1 e(CHS):1023/80/63 s:0 l:390721968
[1] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[2] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
[3] f:00 typ:0 s(CHS):0/0/0 e(CHS):0/0/0 s:0 l:0
GEOM: Configure ad4s1, start 0 length 200049647616 end 200049647615
GEOM: Configure ad4a, start 0 length 1073741824 end 1073741823
GEOM: Configure ad4b, start 1073741824 length 2147483648 end 3221225471
GEOM: Configure ad4c, start 0 length 200049647616 end 200049647615
GEOM: Configure ad4d, start 3221225472 length 4294967296 end 7516192767
GEOM: Configure ad4e, start 7516192768 length 4294967296 end 11811160063
GEOM: Configure ad4f, start 11811160064 length 188238487552 end 200049647615
GEOM: Configure ad4s1a, start 0 length 1073741824 end 1073741823
GEOM: Configure ad4s1b, start 1073741824 length 2147483648 end 3221225471
GEOM: Configure ad4s1c, start 0 length 200049647616 end 200049647615
GEOM: Configure ad4s1d, start 3221225472 length 4294967296 end 7516192767
GEOM: Configure ad4s1e, start 7516192768 length 4294967296 end 11811160063
GEOM: Configure ad4s1f, start 11811160064 length 188238487552 end 200049647615
(probe21:amr0:0:6:0): error 22
(probe21:amr0:0:6:0): Unretryable Error
(probe22:amr0:0:8:0): error 22
(probe22:amr0:0:8:0): Unretryable Error
(probe23:amr0:0:9:0): error 22
(probe23:amr0:0:9:0): Unretryable Error
(probe24:amr0:0:10:0): error 22
(probe24:amr0:0:10:0): Unretryable Error
(probe25:amr0:0:11:0): error 22
(probe25:amr0:0:11:0): Unretryable Error
(probe26:amr0:0:12:0): error 22
(probe26:amr0:0:12:0): Unretryable Error
(probe27:amr0:0:13:0): error 22
(probe27:amr0:0:13:0): Unretryable Error
(probe28:amr0:0:14:0): error 22
(probe28:amr0:0:14:0): Unretryable Error
(probe29:amr0:0:15:0): error 22
(probe29:amr0:0:15:0): Unretryable Error
(probe16:amr0:0:1:0): error 22
(probe16:amr0:0:1:0): Unretryable Error
(probe15:amr0:0:0:0): error 22
(probe15:amr0:0:0:0): Unretryable Error
(probe20:amr0:0:5:0): error 22
(probe20:amr0:0:5:0): Unretryable Error
(probe19:amr0:0:4:0): error 22
(probe19:amr0:0:4:0): Unretryable Error
(probe18:amr0:0:3:0): error 22
(probe18:amr0:0:3:0): Unretryable Error
(probe17:amr0:0:2:0): error 22
(probe17:amr0:0:2:0): Unretryable Error
(ahc0:A:6:0): Sending WDTR 1
(ahc0:A:6:0): Received WDTR 1 filtered to 1
ahc0: target 6 using 16bit transfers
(ahc0:A:6:0): Sending SDTR period c, offset 8
(ahc0:A:6:0): Received SDTR period c, offset 8
Filtered to period c, offset 8
ahc0: target 6 synchronous at 20.0MHz, offset = 0x8
(ahc0:A:6:0): Sending WDTR 1
(ahc0:A:6:0): Received WDTR 1 filtered to 1
ahc0: target 6 using 16bit transfers
(ahc0:A:6:0): Sending SDTR period c, offset 8
(ahc0:A:6:0): Received SDTR period c, offset 8
Filtered to period c, offset 8
ahc0: target 6 synchronous at 20.0MHz, offset = 0x8
pass0 at ahc0 bus 0 target 6 lun 0
pass0: <ARCHIVE Python 06408-XXX 8130> Removable Sequential Access SCSI-3 device
pass0: Serial Number HJ05DV0
pass0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
sa0 at ahc0 bus 0 target 6 lun 0
sa0: <ARCHIVE Python 06408-XXX 8130> Removable Sequential Access SCSI-3 device
sa0: Serial Number HJ05DV0
sa0: 40.000MB/s transfers (20.000MHz, offset 8, 16bit)
ioapic0: routing intpin 1 (IRQ 1) to cluster 0
ioapic0: routing intpin 2 (IRQ 0) to cluster 0
ioapic0: routing intpin 3 (IRQ 3) to cluster 0
ioapic0: routing intpin 4 (IRQ 4) to cluster 0
ioapic0: routing intpin 6 (IRQ 6) to cluster 0
ioapic0: routing intpin 7 (IRQ 7) to cluster 0
ioapic0: routing intpin 8 (IRQ 8) to cluster 0
ioapic0: routing intpin 9 (IRQ 9) to cluster 0
ioapic0: routing intpin 14 (IRQ 14) to cluster 0
ioapic0: routing intpin 15 (IRQ 15) to cluster 0
ioapic0: routing intpin 16 (IRQ 16) to cluster 0
ioapic0: routing intpin 17 (IRQ 17) to cluster 0
ioapic0: routing intpin 19 (IRQ 19) to cluster 0
ioapic1: routing intpin 0 (IRQ 24) to cluster 0
ioapic1: routing intpin 2 (IRQ 26) to cluster 0
Mounting root from ufs:/dev/ad4s1a
start_init: trying /sbin/init
bge0: gigabit link up
More information about the freebsd-amd64
mailing list