5.3-BETA2 works for me

Tue Aug 31 12:42:48 PDT 2004

Wilko Bulte wrote:

> It would be nice if you at some point could verify that the
> installkernel etc boots correctly for you from the installkit.  Just to
> be paranoid ;)

Ok, the BETA2 miniinst image boots.

*** no timer interrupts on CPU 0 ***
Resetting I/O buses...
*** keyboard not plugged in...
>>>show dev
dka0.0.0.5.0               DKA0               SEAGATE ST34573W  6244
dqa0.0.0.11.0              DQA0             Compaq   CRD-8402B  1.01    
dva0.0.0.0.0               DVA0                               
pka0.7.0.5.0               PKA0                  SCSI Bus ID 7
>>>show config
                        Digital AlphaPC 164LX 599 MHz

SRM Console V5.8-1              OpenVMS PALcode V1.21-2, Digital UNIX
                                PALcode V1.23-2

SROM Revision: 3.1.2
Alpha 21164A-2
Pyxis ASIC Pass 2

MEMORY

768 MBytes of system memory

Bank #       Size     Base Addr
------    ----------  ---------
  0         256 MB    020000000
  1         512 MB    000000000

Total Bad Pages = 0
Total Good Memory = 768 MBytes

Bcache Size = 2 MB

PCI Bus 
     Bus 00  Slot 05: NCR 53C895
                                   pka0.7.0.5.0       SCSI Bus ID 7    

                                   dka0.0.0.5.0       SEAGATE ST34573W

     Bus 00  Slot 06: 920010B7/100010B7

     Bus 00  Slot 08: Intel 82378
                                                      Bridge to Bus 1, ISA
     Bus 00  Slot 11: CMD PCI0646 IDE
                                   dqa.0.0.11.0                           

                                   dqa0.0.0.11.0      Compaq  CRD-8402B  

ISA
Slot    Device  Name            Type         Enabled  BaseAddr  IRQ    
DMA
0
        0       MOUSE           Embedded        Yes     60      12      
        1       KBD             Embedded        Yes     60      1       
        2       COM1            Embedded        Yes     3f8     4       
        3       COM2            Embedded        Yes     2f8     3       
        4       LPT1            Embedded        Yes     3bc     7       
        5       FLOPPY          Embedded        Yes     3f0     6       2

>>>boot dqa0
(boot dqa0.0.0.11.0)
block 0 of dqa0.0.0.11.0 is a valid boot block
reading 409 blocks from dqa0.0.0.11.0
bootstrap code read in
base = 200000, image_start = 0, image_bytes = 33200
initializing HWRPB at 2000
initializing page table at 2ffec000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
Console: SRM firmware console
VMS PAL rev: 0x1000200010115
OSF PAL rev: 0x1000200020117
Switch to OSF PAL code succeeded.

FreeBSD/alpha SRM CD9660 boot, Revision 1.2
(root at ds10.wbnet, Mon Aug 30 03:48:07 UTC 2004)
Memory: 786432 k
Loading /boot/defaults/loader.conf 
/boot/kernel/kernel data=0x5b77f0+0x4d110 syms=[0x8+0x68b20+0x8+0x5564f]
-
Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...               
Entering /boot/kernel/kernel at 0xfffffc0000346fe0...
GDB: debug ports: sio
GDB: current port: sio
KDB: debugger backends: ddb gdb
KDB: current backend: ddb
Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.3-BETA2 #0: Mon Aug 30 17:59:15 UTC 2004
    root at ds10.wbnet:/usr/obj/usr/src/sys/GENERIC
EB164
Digital AlphaPC 164LX 599 MHz, 598MHz
8192 byte page size, 1 processor.
CPU: EV56 (21164A) major=7 minor=2 extensions=0x1<BWX>
OSF PAL rev: 0x1000200020117
real memory  = 803119104 (765 MB)
avail memory = 772694016 (736 MB)
cia0: <2117x Core Logic chipset>
cia0: Pyxis, pass 1
cia0: extended capabilities: 1<BWEN>
pcib0: <2117x PCI host bus adapter> on cia0
pci0: <PCI bus> on pcib0
sym0: <895> port 0x10000-0x100ff mem
0x82030000-0x82030fff,0x82031000-0x820310ff irq 2 at device 5.0 on pci0
sym0: Tekram NVRAM, ID 7, Fast-40, SE, parity checking
sym0: interrupting at CIA irq 2
sym0: [GIANT-LOCKED]
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0x10100-0x1017f mem
0x82031100-0x8203117f irq 0 at device 6.0 on pci0
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
xl0: Ethernet address: 00:01:02:b4:75:9e
xl0: interrupting at CIA irq 0
xl0: [GIANT-LOCKED]
isab0: <PCI-ISA bridge> at device 8.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <CMD 646 WDMA2 controller> port
0x10190-0x1019f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 irq 5 at device 11.0
on pci0
atapci0: interrupting at CIA irq 5
ata0: channel #0 on atapci0
ata0: interrupting at ISA irq 14
ata1: channel #1 on atapci0
ata1: interrupting at ISA irq 15
orm0: <ISA Option ROM> at iomem 0xc0000-0xc7fff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
atkbd0: interrupting at ISA irq 1
atkbd0: [GIANT-LOCKED]
fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port
0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
fdc0: interrupting at ISA irq 6
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
mcclock0: <MC146818A real time clock> at port 0x70-0x71 on isa0
ppc0: <Parallel port> at port 0x3bc-0x3c3 irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
ppbus0: <Parallel port bus> on ppc0
lpt0: <Printer> on ppbus0
lpt0: Polled port
ppi0: <Parallel I/O> on ppbus0
ppc0: interrupting at ISA irq 7
sc0: <System console> on isa0
sc0: VGA <16 virtual consoles, flags=0x0>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A, console
sio0: interrupting at ISA irq 4
sio1 at port 0x2f8-0x2ff irq 3 flags 0x80 on isa0
sio1: type 16550A
sio1: interrupting at ISA irq 3
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "i8254" frequency 1193182 Hz quality 0
Timecounter "alpha" frequency 599839579 Hz quality 0
Timecounters tick every 0.976 msec
md0: Preloaded image </boot/mfsroot> 4423680 bytes at 0xfffffc00009c2a80
ATAPI_RESET time = 190us
acd0: CDROM <Compaq CRD-8402B/1.01> at ata0-master PIO4
Waiting 15 seconds for SCSI devices to settle
(noperiph:sym0:0:-1:-1): SCSI BUS mode change from SE to SE.
da0 at sym0 bus 0 target 0 lun 0
da0: <SEAGATE ST34573W 6244> Fixed Direct Access SCSI-2 device 
da0: 40.000MB/s transfers (20.000MHz, offset 15, 16bit), Tagged Queueing
Enabled
da0: 4340MB (8888924 512 byte sectors: 255H 63S/T 553C)
Mounting root from ufs:/dev/md0
/stand/sysinstall running as init on serial console

These are the predefined terminal types available to
sysinstall when running stand-alone.  Please choose the
closest match for your particular terminal.

1 ...................... Standard ANSI terminal.
2 ...................... VT100 or compatible terminal.
3 ...................... FreeBSD system console (color).
4 ...................... FreeBSD system console (monochrome).

5 ...................... xterm terminal emulator.

Your choice: (1-5) 

-- 
 Oliver Lehmann
  http://www.pofo.de/
  http://wishlist.ans-netz.de/