Does anyone use a FDDI card on 5.0?

[Oliver Lehmann]

Same here:

*** keyboard not plugged in...

halted CPU 0

halt code = 5
HALT instruction executed
PC = fffffc000051fee0
*** no timer interrupts on CPU 0 ***

CPU 0 booting

Resetting I/O buses...
*** keyboard not plugged in...
(boot dka0.0.0.5.0)
block 0 of dka0.0.0.5.0 is a valid boot block
reading 15 blocks from dka0.0.0.5.0
bootstrap code read in
base = 200000, image_start = 0, image_bytes = 1e00
initializing HWRPB at 2000
initializing page table at 2ffec000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code                                                 
                                                                          
         Loading /boot/loader
Console: SRM firmware console
VMS PAL rev: 0x1000200010115
OSF PAL rev: 0x1000200020117
Switch to OSF PAL code succeeded.

FreeBSD/alpha SRM disk boot, Revision 1.2
(olivleh1 at dill.salatschuessel.net, Sun Mar 23 19:14:47 CET 2003)
Memory: 786432 k
Loading /boot/defaults/loader.conf 
/boot/kernel/kernel data=0x2c7630+0x53140 syms=[0x8+0x474c0+0x8+0x36fdf]

Hit [Enter] to boot immediately, or any other key for command prompt.
Booting [/boot/kernel/kernel]...               
Entering /boot/kernel/kernel at 0xfffffc0000330de0...
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.0-RELEASE-p6 #1: Mon Mar 31 16:17:19 CEST 2003
    olivleh1 at dill.salatschuessel.net:/usr/obj/usr/src/sys/DILL
Preloaded elf kernel "/boot/kernel/kernel" at 0xfffffc000069c000.
EB164
Digital AlphaPC 164LX 599 MHz, 598MHz
8192 byte page size, 1 processor.
CPU: EV56 (21164A) major=7 minor=2 extensions=0x1<BWX>
OSF PAL rev: 0x1000200020117
real memory  = 803119104 (765 MB)
avail memory = 775102464 (739 MB)
Initializing GEOMetry subsystem
cia0: <2117x Core Logic chipset>
cia0: Pyxis, pass 1
cia0: extended capabilities: 1<BWEN>
pcib0: <2117x PCI host bus adapter> on cia0
pci0: <PCI bus> on pcib0
sym0: <895> port 0x10000-0x100ff mem
0x82040000-0x82040fff,0x82041000-0x820410ff irq 2 at device 5.0 on pci0
sym0: Tekram NVRAM, ID 7, Fast-40, SE, parity checking
sym0: interrupting at CIA irq 2
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0x10100-0x1017f mem
0x82041100-0x8204117f irq 0 at device 6.0 on pci0
xl0: interrupting at CIA irq 0
xl0: Ethernet address: 00:01:02:b4:75:9e
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI-ISA bridge> at device 8.0 on pci0
isa0: <ISA bus> on isab0
fpa0: <Digital DEFPA PCI FDDI Controller> port 0x10180-0x101ff mem
0x82030000-0x8203ffff,0x82041180-0x820411ff irq 3 at device 9.0 on pci0

unexpected machine check:

    mces    = 0x1
    vector  = 0x660
    param   = 0xfffffc0000006068
    pc      = 0xfffffc00005186c4
    ra      = 0xfffffc000038ff2c
    curproc = 0xfffffc00005d6bc8
        pid = 0, comm = swapper

panic: machine check
Uptime: 1s
Automatic reboot in 15 seconds - press a key on the console to abort
Rebooting...


-- 
 Oliver Lehmann
        @home: lehmann at ans-netz.de
      @office: oliver.lehmann at mgi.de
         @www: http://www.pofo.de/  |  http://wishlist.ans-netz.de/