Disbabling a certain

Jerry Haltom jhaltom at feedbackplusinc.com
Fri Feb 6 10:57:27 PST 2004 

Attached is the output with raid enabled. Will reply again with no raid,
just wanted to get this out while the system rebooted. :)

On Fri, 2004-02-06 at 12:44, Justin T. Gibbs wrote:
> > I have a Dell PowerEdge 2300 that I am trying to load Linux on. it has
> > two SCSI controllers in it, one is RAID the other is not.
> > 
> > I believe the raid one is handled by megaraid, and the non raid is
> > handled by aic7xxx. However, loading aic7xxx prevents the loading of the
> > megaraid model (probably because the aic7xxx grabs the megaraid
> > device???) Is there a way to specify to the aic7xxx module to only load
> > a specific device and not all?
> 
> The megaraid folks must not be using the same convention as that used
> for Adaptec ROMB.  Can you provide the output from "lspci -vv -n" for
> the system with and without the RAID enabled?
> 
> --
> Justin



-- 
Jerry Haltom <jhaltom at feedbackplusinc.com>
Feedback Plus, Inc.
-------------- next part --------------
00:00.0 Class 0600: 8086:7190 (rev 03)
	Subsystem: 1028:0081
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort+ <MAbort+ >SERR- <PERR-
	Latency: 32
	Region 0: Memory at f0000000 (32-bit, prefetchable) [size=64M]
	Capabilities: [a0] AGP version 1.0
		Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1,x2
		Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

00:01.0 Class 0604: 8086:7191 (rev 03)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=32
	I/O behind bridge: 0000f000-0000ffff
	Memory behind bridge: fb000000-fdffffff
	Prefetchable memory behind bridge: f7000000-f7ffffff
	BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B+

00:02.0 Class 0604: 1011:0024 (rev 03)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort+ <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, cache line size 08
	Bus: primary=00, secondary=02, subordinate=03, sec-latency=32
	I/O behind bridge: 0000e000-0000efff
	Memory behind bridge: f9000000-faffffff
	Prefetchable memory behind bridge: 00000000f5000000-00000000f6f00000
	BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=220mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-
		Bridge: PM- B3+

00:07.0 Class 0601: 8086:7110 (rev 02)
	Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 0

00:07.1 Class 0101: 8086:7111 (rev 01) (prog-if 80 [Master])
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Region 4: I/O ports at 1000 [size=16]

00:07.2 Class 0c03: 8086:7112 (rev 01)
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin D routed to IRQ 0
	Region 4: I/O ports at 1020 [size=32]

00:07.3 Class 0680: 8086:7113 (rev 02)
	Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Interrupt: pin ? routed to IRQ 9

00:0c.0 Class 0200: 10b7:9055 (rev 30)
	Subsystem: 10b7:9055
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (2500ns min, 2500ns max), cache line size 08
	Interrupt: pin A routed to IRQ 22
	Region 0: I/O ports at dc80 [size=128]
	Region 1: Memory at fe000000 (32-bit, non-prefetchable) [size=128]
	Expansion ROM at f8000000 [disabled] [size=128K]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold+)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

01:00.0 Class 0300: 1002:4744 (rev 5c)
	Subsystem: 1028:0081
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop+ ParErr- Stepping+ SERR- FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (2000ns min), cache line size 08
	Region 0: Memory at fc000000 (32-bit, non-prefetchable) [size=16M]
	Region 1: I/O ports at fc00 [size=256]
	Region 2: Memory at fbfff000 (32-bit, non-prefetchable) [size=4K]
	Expansion ROM at <unassigned> [disabled] [size=128K]
	Capabilities: [50] AGP version 1.0
		Status: RQ=256 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64- HTrans- 64bit- FW- AGP3- Rate=x1
		Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit- FW- Rate=<none>

02:04.0 Class 0100: 9005:001f
	Subsystem: 1028:0081
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (9750ns min, 6250ns max), cache line size 08
	Interrupt: pin A routed to IRQ 16
	BIST result: 00
	Region 0: I/O ports at ec00 [size=256]
	Region 1: Memory at f9fff000 (64-bit, non-prefetchable) [size=4K]
	Expansion ROM at fa000000 [disabled] [size=128K]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:06.0 Class 0100: 9004:6078 (rev 03)
	Subsystem: 9004:7860
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32 (1000ns min, 1000ns max), cache line size 08
	Interrupt: pin A routed to IRQ 16
	Region 0: I/O ports at e800 [size=256]
	Region 1: Memory at f9ffe000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [dc] Power Management version 1
		Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
		Status: D0 PME-Enable- DSel=0 DScale=0 PME-

02:0a.0 Class 0604: 8086:0960 (rev 05)
	Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, cache line size 08
	Bus: primary=02, secondary=03, subordinate=03, sec-latency=32
	BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-

02:0a.1 Class 0e00: 8086:1960 (rev 05) (prog-if 01)
	Subsystem: 1111:1111
	Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
	Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
	Latency: 32, cache line size 08
	Interrupt: pin A routed to IRQ 18
	Region 0: Memory at f6c00000 (32-bit, prefetchable) [size=4M]
	Expansion ROM at fa000000 [disabled] [size=32K]

-------------- next part --------------
A non-text attachment was scrubbed...
Name: not available
Type: application/pgp-signature
Size: 189 bytes
Desc: This is a digitally signed message part
Url : http://lists.freebsd.org/pipermail/aic7xxx/attachments/20040206/7f0a8d3a/attachment.bin

More information about the aic7xxx mailing list