New 2940U2W with quantum drive

[System Administrator]

Hi,

First of all, my config is
intel pr440fx motherboard with onboard adaptec 7880. have on the cable 2 9
Gig Quantum Atlas IIs (one is my boot drive), 1 4.5G Quantum Viking, and 1
4.1G(?) Quantum Grand Prix. the controller is on IRQ 9 by the bios, then
IO-APICs in the linux kernel move it to IRQ 17.

Now, I've added a new 2940U2W controller. On the controller I put a new
18.2G Quantum Atlas III (LVD,68pin).

When I bootup the computer it detects the new controller first, then the
7880. The problem with this is instead of booting into linux it says
"Insert bootable media into appropriate drive"
I'm assuming it's trying to boot from the new 18.2G drive, drive that
controller was detected first. The only was I could get it to boot was to
go into Cntrl-A on the NEW controller and turn the SCSI bios off. Then it
booted fine..the kernel detected the new drive and controller and I can
use them fine, but when it detected the new drive it says synchronus at
40MB/S..which it should be 80. 

(scsi1) Wide Channel, SCSI ID=7, 32/255 SCBs
(scsi1) Downloading sequencer code... 407 instructions downloaded
scsi1 : Adaptec AHA274x/284x/294x (EISA/VLB/PCI-Fast SCSI) 5.1.10/3.2.4
       <Adaptec AHA-294X Ultra2 SCSI host adapter>
Detected scsi disk sde at scsi1, channel 0, id 4, lun 0
(scsi1:0:4:0) Synchronous at 40.0 Mbyte/sec, offset 31.
SCSI device sde: hdwr sector= 512 bytes. Sectors= 35566499 [17366 MB]
[17.4 GB]

how can i get this to recognize it as 80 MB/S?

/proc/scsi/aic7xxx/1:
Adaptec AIC7xxx driver version: 5.1.10/3.2.4
Compile Options:
  AIC7XXX_RESET_DELAY    : 10
  AIC7XXX_TAGGED_QUEUEING: Adapter Support Enabled
                             Check below to see which
                             devices use tagged queueing
  AIC7XXX_PAGE_ENABLE    : Enabled (This is no longer an option)
  AIC7XXX_PROC_STATS     : Enabled

Adapter Configuration:
           SCSI Adapter: Adaptec AHA-294X Ultra2 SCSI host adapter
                           Ultra2-LVD/SE Wide Controller
    PCI MMAPed I/O Base: 0xffbef000
 Adapter SEEPROM Config: SEEPROM found and used.
      Adaptec SCSI BIOS: Disabled
                    IRQ: 17
                   SCBs: Active 0, Max Active 1,
                         Allocated 15, HW 32, Page 255
             Interrupts: 284781
      BIOS Control Word: 0x18a2
   Adapter Control Word: 0x1c5d
   Extended Translation: Enabled
Disconnect Enable Flags: 0xffff
     Ultra Enable Flags: 0x0000
 Tag Queue Enable Flags: 0x0000
Ordered Queue Tag Flags: 0x0000
Default Tag Queue Depth: 24
    Tagged Queue By Device array for aic7xxx host instance 1:
      {255,255,255,255,255,255,255,255,255,255,255,255,255,255,255,255}
    Actual queue depth per device for aic7xxx host instance 1:
      {1,1,1,1,1,1,1,1,1,1,1,1,1,1,1,1}

Statistics:

(scsi1:0:4:0)
  Device using Wide/Sync transfers at 40.0 MByte/sec, offset 31
  Transinfo settings: current(12/31/1), goal(10/127/1), user(10/127/1)
  Total transfers 284712 (55061 reads and 229651 writes)
             < 2K      2K+     4K+     8K+    16K+    32K+    64K+   128K+
   Reads:       1   49240     376     472    1897    1311    1271     493
  Writes:       0  176896   16372    2227    2847    4773    8414   18122


Thanx:

-Cygnus
.-._.-._.-._.-._.-._.-._.-._.-._.-._.-._.-._.-._.-._.-._.-._.-._.-._.-.
Anthony J. Biacco                       Network Administrator/Engineer
admin at intergrafix.net                    Intergrafix Internet Services

    "Dream as if you'll live forever, live as if you'll die today"
http://cygnus.ncohafmuta.com                http://www.intergrafix.net
.-._.-._.-._.-._.-._.-._.-._.-._.-._.-._.-._.-._.-._.-._.-._.-._.-._.-.



To Unsubscribe: send mail to majordomo at FreeBSD.org
with "unsubscribe aic7xxx" in the body of the message