booting FreeBSD 13 release
- Go to: [ bottom of page ] [ top of archives ] [ this month ]
Date: Fri, 16 Jul 2021 16:49:49 UTC
Hello Justin, I am trying to boot FreeBSD 13. How to I set loaderdev? It doesn't find the kernel. Kind Regards, Al U-Boot 2014.04 (Oct 17 2016 - 08:22:22) CPU0: P5020, Version: 2.0, (0x82200020) Core: e5500, Version: 1.2, (0x80240012) Clock Configuration: CPU0:1995 MHz, CPU1:1995 MHz, CCB:798 MHz, DDR:665 MHz (1330 MT/s data rate) (Asynchronous), LBC:49.875 MHz FMAN1: 498.750 MHz QMAN: 399 MHz PME: 399 MHz L1: D-cache 32 KiB enabled I-cache 32 KiB enabled Reset Configuration Word (RCW): 00000000: 0c540000 00000000 1e1e0000 00000000 00000010: 44808c00 ff002000 68000000 45000000 00000020: 00000000 00000000 00000000 0003000f 00000030: a0000000 00000000 00000000 00000000 Board: CYRUS 36-bit Addressing I2C: ready SPI: ready DRAM: Initializing....using SPD Detected UDIMM KHX1600C10D3/8G Detected UDIMM KHX1600C10D3/8G 14 GiB left unmapped 16 GiB (DDR3, 64-bit, CL=9, ECC off) DDR Controller Interleaving Mode: cache line DDR Chip-Select Interleaving Mode: CS0+CS1 Local Bus Controller Registers BR0 0xE0001001 OR0 0xFFF00010 BR1 0xE1001001 OR1 0xFFF00010 BR2 0x00000000 OR2 0x00000000 BR3 0x00000000 OR3 0x00000000 BR4 0x00000000 OR4 0x00000000 BR5 0x00000000 OR5 0x00000000 BR6 0x00000000 OR6 0x00000000 BR7 0x00000000 OR7 0x00000000 LBCR 0x40000000 LCRR 0x80010004 L2: 512 KiB enabled Corenet Platform Cache: 2 MiB enabled SERDES: bank 2 disabled MMC: FSL_SDHC: 0 EEPROM: NXID v0 PCIe1: Root Complex, x4 gen1, regs @ 0xfe200000 01:00.0 - 1002:6759 - Display controller 01:00.1 - 1002:aa90 - Multimedia device PCIe1: Bus 00 - 01 PCIe2: Root Complex, x4 gen2, regs @ 0xfe201000 03:00.0 - 111d:8092 - Bridge device 04:01.0 - 111d:8092 - Bridge device 05:00.0 - 12d8:e111 - Bridge device 04:02.0 - 111d:8092 - Bridge device 04:03.0 - 111d:8092 - Bridge device 08:00.0 - 8086:10d3 - Network controller 04:08.0 - 111d:8092 - Bridge device 04:10.0 - 111d:8092 - Bridge device PCIe2: Bus 02 - 0a PCIe3: disabled PCIe4: disabled Looking for VGA PINS: 0xfc000808 videoboot: Booting PCI video card bus 1, function 0, device 0 Begin BIOS POST End BIOS POST Setting VESA Mode Found required VESA mode About to set mode 279 About to get mode Got mode 49431 (0xc117) OK XSize = 1024 YSize = 768 Base =0xe0000000 mmio_base = 0x80000000 bgx = 0xad55ad55 fgx = 0x0 In: serial Out: serial Err: serial ID: NXID v0 SN: 116330081 UID: 4429431001910051c47da080a0800000 Errata: Q Build date: 2015/07/06 14:51:17 CRC: eb5fb57a SCSI: scanning bus for devices... Found 0 device(s). Net: Initializing Fman MMC read: dev # 0, block # 1130, count 128 ... Fman1: Uploading microcode version 106.1.0 Tuning PHY @ 3 Tuning PHY @ 7 FM1@DTSEC4 [PRIME], FM1@DTSEC5 MMC read: dev # 0, block # 1280, count 512 ... 512 blocks read: OK MMC read: dev # 0, block # 65536, count 131072 ... 131072 blocks read: OK USB0: USB EHCI 1.00 scanning bus 0 for devices... ERROR: Invalid USB EP length (9) ERROR: Invalid USB EP length (9) 4 USB Device(s) found USB1: USB EHCI 1.00 scanning bus 1 for devices... 4 USB Device(s) found SATA0 (3 Gbps) SATA1 (No RDY) scanning bus for devices... Found 0 device(s). X5000> setenv loader_kernaddr 0x2000000 X5000> fatload sata 0:1 $loadaddr ubldr reading ubldr 315292 bytes read in 27 ms (11.1 MiB/s) X5000> fatload sata 0:1 $fdtaddr cyrus.dtb reading cyrus.dtb 65536 bytes read in 31 ms (2 MiB/s) X5000> fdt addr $fdtaddr X5000> fdt boardsetup X5000> bootelf $loadaddr ## Starting application at 0x00010160 ... Consoles: U-Boot console Compatible U-Boot API signature found @0x7fe2efd8 FreeBSD/powerpc64 U-Boot loader, Revision 1.1 Number of U-Boot devices: 4 U-Boot env: loaderdev not set, will probe all devices. Found U-Boot device: disk Probing all <unknown> devices... Checking unit=0 slice=<auto> partition=<auto>... Checking unit=1 slice=<auto> partition=<auto>... Checking unit=2 slice=<auto> partition=<auto>...Non-NCQ command time out Non-NCQ command time out Non-NCQ command time out Found U-Boot device: net Booting from net0: bootp: no reply No response for RARP request net_open: RARP failed bootp: no reply No response for RARP request net_open: RARP failed bootp: no reply No response for RARP request net_open: RARP failed bootp: no reply No response for RARP request net_open: RARP failed bootp: no reply No response for RARP request net_open: RARP failed bootp: no reply No response for RARP request net_open: RARP failed bootp: no reply