Re: Ralink RT3050F
- Reply: Archimedes Gaviola : "Re: Ralink RT3050F"
- In reply to: Archimedes Gaviola : "Re: Ralink RT3050F"
- Go to: [ bottom of page ] [ top of archives ] [ this month ]
Date: Tue, 30 Aug 2022 15:03:42 UTC
Hey Archimedes, for a good start you can setup bootp, since network working. Otherwise use geom_map to split flash into parts and put ulzma compressed rootfs into a filesystem partition. After deletion of MIPS support from the tree, interest in it grew :) Thanks. пн, 29 серп. 2022 р. о 05:21 Archimedes Gaviola < archimedes.gaviola@gmail.com> пише: > On Sun, Aug 28, 2022 at 4:15 PM Archimedes Gaviola < > archimedes.gaviola@gmail.com> wrote: > >> Hi, >> >> After I successfully accessed the serial console, I proceeded to load the >> kernel image (this is an old D-link DIR-600 (B2) Wi-Fi device) and >> encountered this error -> >> >> Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to recover. >> >> Any idea what have I missed? After this failure, it booted to the default >> image of the Linux system. Haven't flashed the image yet when this error >> occurred. >> >> TFTP from server 192.168.1.209; our IP address is 192.168.1.188 >> Filename 'dlink/kernel.bin.lzma.uboot'. >> >> TIMEOUT_COUNT=10,Load address: 0x80800000 >> Loading: Got ARP REQUEST, return our IP >> >> ArpTimeoutCheck >> Got ARP REPLY, set server/gtwy eth addr (b8:27:eb:64:8b:57) >> Got it >> ################################################################# >> ################################################################# >> ################################################################# >> ################################################ >> done >> Bytes transferred = 1243362 (12f8e2 hex) >> NetBootFileXferSize= 0012f8e2 >> >> RT3052 # bootm 0x80800000 >> ## Booting image at 80800000 ... >> Image Name: FreeBSD Kernel Image >> Created: 2022-08-18 5:51:56 UTC >> Image Type: MIPS Linux Kernel Image (lzma compressed) >> Data Size: 1243298 Bytes = 1.2 MB >> Load Address: 80001100 >> Entry Point: 80001100 >> Verifying Checksum ... OK >> Uncompressing Kernel Image ... LZMA ERROR 1 - must RESET board to >> recover >> >> >> U-Boot 1.1.3 (Jan 12 2011 - 21:35:28) (ALPHA) >> >> SVN revision: 482 >> Target board: WRG-N23 >> >> Board: Ralink APSoC DRAM: 32 MB >> config usb..*** Error: D+/D- is 1/1, config usb failed. >> ..*** Error: D+/D- is 1/1, config usb failed. >> >> ****************************** >> Software System Reset Occurred >> ****************************** >> >> Set info->start[0]=BF000000 >> ============================================ >> Ralink UBoot Version: 3.5.1.0 >> -------------------------------------------- >> ASIC 3052_MP2 (Port5<->None) >> DRAM component: 256 Mbits SDR >> DRAM bus: 16 bit >> Total memory: 32 MBytes >> Flash component: NOR Flash >> Date:Jan 12 2011 Time:21:35:28 >> ============================================ >> icache: sets:256, ways:4, linesz:32 ,total:32768 >> dcache: sets:128, ways:4, linesz:32 ,total:16384 >> ## Powering down port 0 ~ 3. >> >> Please choose the operation: >> 1: Load system code to SDRAM via TFTP. >> 2: Load system code then write to Flash via TFTP. >> 3: Boot system code via Flash (default). >> 4: Entr boot command line interface. >> 7: Load Boot Loader code then write to Flash via Serial. >> 9: Load Boot Loader code then write to Flash via TFTP. >> 0 >> >> 3: System Boot system code via Flash. >> ## Booting image at bf050000 ... >> addr:bf050000 >> We have SEAMA, Image Size = 3506208 >> Verifying Checksum ... >> Uncompressing SEAMA linux.lzma ... OK >> ## Transferring control to Linux (at address 81f46ec0) ... >> ## Giving linux memsize in MB, 32 >> >> Starting kernel ... >> >> LINUX started... >> >> THIS IS ASIC >> is_RT3052 = 0, is_RT3352 = 0 >> is_RT3350 = 1, is_RT5350 = 0 >> Linux version 2.6.33.2 (kwest@enzo) (gcc version 4.3.3 (GCC) ) #1 Fri >> Dec 10 17:24:50 CST 2010 >> ... >> >> Thanks and best regards, >> Archimedes >> > > Hi, > > Alright I made some progress, I used gzip compression instead of LZMA and > the kernel image is now booting. > > U-Boot 1.1.3 (Jan 12 2011 - 21:35:28) (ALPHA) > > SVN revision: 482 > Target board: WRG-N23 > > Board: Ralink APSoC DRAM: 32 MB > config usb..*** Error: D+/D- is 1/1, config usb failed. > ..*** Error: D+/D- is 1/1, config usb failed. > > ****************************** > Software System Reset Occurred > ****************************** > > Set info->start[0]=BF000000 > ============================================ > Ralink UBoot Version: 3.5.1.0 > -------------------------------------------- > ASIC 3052_MP2 (Port5<->None) > DRAM component: 256 Mbits SDR > DRAM bus: 16 bit > Total memory: 32 MBytes > Flash component: NOR Flash > Date:Jan 12 2011 Time:21:35:28 > ============================================ > icache: sets:256, ways:4, linesz:32 ,total:32768 > dcache: sets:128, ways:4, linesz:32 ,total:16384 > ## Powering down port 0 ~ 3. > > Please choose the operation: > 1: Load system code to SDRAM via TFTP. > 2: Load system code then write to Flash via TFTP. > 3: Boot system code via Flash (default). > 4: Entr boot command line interface. > 7: Load Boot Loader code then write to Flash via Serial. > 9: Load Boot Loader code then write to Flash via TFTP. > 0 > > 3: System Boot system code via Flash. > ## Booting image at bf050000 ... > Image Name: FreeBSD Kernel Image > Created: 2022-08-29 1:55:22 UTC > Image Type: MIPS Linux Kernel Image (gzip compressed) > Data Size: 1724519 Bytes = 1.6 MB > Load Address: 80001100 > Entry Point: 80001100 > Verifying Checksum ... OK > Uncompressing Kernel Image ... OK > > Starting kernel ... > > U-Boot args (from 0 args): > None > Environment: > entry: mips_init() > Cache info: > picache_stride = 4096 > picache_loopcount = 8 > pdcache_stride = 4096 > pdcache_loopcount = 4 > cpu0: MIPS Technologies processor v76.150 > MMU: Standard TLB, 32 entries (4K 16K 64K 256K 1M 16M 64M 256M pg sizes) > L1 i-cache: 4 ways of 256 sets, 32 bytes per line > L1 d-cache: 4 ways of 128 sets, 32 bytes per line > L2 cache: disabled > Config1=0xbea3319e<PerfCount,WatchRegs,MIPS16,EJTAG> > Config2=0x80000000 > Config3=0x420 > Physical memory chunk(s): > 0x438000 - 0x1ffffff, 29130752 bytes (7112 pages) > Maxmem is 0x2000000 > KDB: debugger backends: ddb > KDB: current backend: ddb > Copyright (c) 1992-2020 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 11.4-RELEASE #1: Sun Aug 28 18:35:56 UTC 2022 > root@:/usr/obj/mips.mipsel/usr/src/sys/RT305X mips > gcc version 4.2.1 20070831 patched [FreeBSD] > Preloaded elf kernel "kernel" at 0x804323d0. > real memory = 33554432 (32768K bytes) > Physical memory chunk(s): > 0x004c4000 - 0x01f46fff, 27799552 bytes (6787 pages) > avail memory = 27365376 (26MB) > ULE: setup cpu 0 > wlan: <802.11 Link Layer> > random: entropy device external interface > mem: <memory> > null: <full device, null device, zero device> > nfslock: pseudo-device > nexus0: <MIPS32 root nexus> > random: harvesting attach, 8 bytes (4 bits) from nexus0 > nvram2env0: base=0x1f030000 sig=0xe5e60a74 maxsize=0x00002000 > flags=0x00000003 > nvram2env1: base=0x1f032000 sig=0x5a045e94 maxsize=0x00004000 > flags=0x00000003 > clock0: <Generic MIPS32 ticker> on nexus0 > Timecounter "MIPS32" frequency 192000000 Hz quality 800 > Event timer "MIPS32" frequency 192000000 Hz quality 800 > random: harvesting attach, 8 bytes (4 bits) from clock0 > obio0 at mem 0x10000000-0x1fffffff on nexus0 > rt305x_sysctl0: <RT305X System Control driver> at mem > 0x10000000-0x100000ff irq 0 on obio0 > Chip ID: "RT3350 " > SYSCTL_SYSCFG=0x3400000 > GE0 mode 3 > Boot from 0x1f000000 > Boot from 0 > Bootstrap test code 0 > SRAM_CS mode 0 > 8mA SDRAM_CLK driving > SYSCTL_CLKCFG0=0x40000000 > SDRAM_CLK_SKEW 1ns > SYSCTL_CLKCFG1=0x04283c > USB OTG clock is enabled > I2S clock is internal 15.625MHz > I2S clock divider 40 > PCM clock is internal 15.625MHz > PCM clock divider 60 > SYSCTL_GPIOMODE=0x00039c > random: harvesting attach, 8 bytes (4 bits) from rt305x_sysctl0 > rt305x_ic0: <RT305X Interrupt Controller driver> at mem > 0x10000200-0x100002ff on obio0 > random: harvesting attach, 8 bytes (4 bits) from rt305x_ic0 > uart0: <rt305x_uart> at mem 0x10000500-0x100005ff irq 5 on obio0 > uart0: fast interrupt > uart0: PPS capture mode: DCDinvalid > random: harvesting attach, 8 bytes (4 bits) from uart0 > gpio0: <RT305X GPIO driver> at mem 0x10000600-0x100006ff irq 6 on obio0 > gpio0: Use reset_gpio 10 > gpiobus0: <GPIO bus> on gpio0 > gpiobus0: <unknown device> at pin 0 > gpiobus0: <unknown device> at pin 7 > gpioled0: <GPIO led> at pin 8 on gpiobus0 > random: harvesting attach, 8 bytes (4 bits) from gpioled0 > gpioled1: <GPIO led> at pin 9 on gpiobus0 > random: harvesting attach, 8 bytes (4 bits) from gpioled1 > gpiobus0: <unknown device> at pin 10 > gpiobus0: <unknown device> at pin 11 > gpioled2: <GPIO led> at pin 14 on gpiobus0 > random: harvesting attach, 8 bytes (4 bits) from gpioled2 > random: harvesting attach, 8 bytes (4 bits) from gpiobus0 > gpioc0: <GPIO controller> on gpio0 > random: harvesting attach, 8 bytes (4 bits) from gpioc0 > random: harvesting attach, 8 bytes (4 bits) from gpio0 > uart1: <rt305x_uart> at mem 0x10000c00-0x10000cff irq 12 on obio0 > uart1: console (115200,n,8,1) > uart1: fast interrupt > uart1: PPS capture mode: DCDinvalid > random: harvesting attach, 8 bytes (4 bits) from uart1 > random: harvesting attach, 8 bytes (4 bits) from obio0 > rt0: <Ralink RT3050 onChip Ethernet driver> at mem 0x10100000-0x1010ffff > irq 3 on nexus0 > rt0: RT305XF Ethernet MAC (rev 0x00000000) > rt0: use hardcoded 00:18:e7:d5:83:90 macaddr > rt0: bpf attached > rt0: Ethernet address: 00:18:e7:d5:83:90 > random: harvesting attach, 8 bytes (4 bits) from rt0 > Device configuration finished. > Timecounters tick every 10.000 msec > vlan: initialized, using hash tables with chaining > lo0: bpf attached > tcp_init: net.inet.tcp.tcbhashsize auto tuned to 512 > bootpc_init: wired to interface 'rt0' > Sending DHCP Discover packet from interface rt0 (00:18:e7:d5:83:90) > Received DHCP Offer packet on rt0 from 192.168.1.1 (accepted) > Received DHCP Offer packet on rt0 from 192.168.1.1 (ignored) > Sending DHCP Request packet from interface rt0 (00:18:e7:d5:83:90) > Received DHCP Ack packet on rt0 from 192.168.1.1 (accepted) > rt0 at 192.168.1.225 server 192.168.1.1 > subnet mask 255.255.255.0 router 192.168.1.1 > Adjusted interface rt0 > Trying to mount root from cd9660:/dev/map/rootfs.uzip []... > mountroot: waiting for device /dev/map/rootfs.uzip... > Mounting from cd9660:/dev/map/rootfs.uzip failed with error 19. > > Loader variables: > > Manual root filesystem specification: > <fstype>:<device> [options] > Mount <device> using filesystem <fstype> > and with the specified (optional) option list. > > eg. ufs:/dev/da0s1a > zfs:tank > cd9660:/dev/cd0 ro > (which is equivalent to: mount -t cd9660 -o ro /dev/cd0 /) > > ? List valid disk boot devices > . Yield 1 second (for background tasks) > <empty line> Abort manual input > > mountroot> > > Another challenge is this last part on mounting the root filesystem? Any > ideas? I'm almost there. > > Thanks and best regards, > Archimedes > > >> >> >> >> On Fri, Aug 19, 2022 at 8:56 AM Archimedes Gaviola < >> archimedes.gaviola@gmail.com> wrote: >> >>> >>> >>> On Fri, Aug 19, 2022 at 8:33 AM Mori Hiroki <yamori813@yahoo.co.jp> >>> wrote: >>> >>>> Hi. >>>> >>>> 0x80800000 is only u-boot image load offset. You will do bootm command >>>> on u-boot then start at 0x80001100 if you create this address by >>>> uboot_mkimage . >>>> >>>> Hiroki Mori >>>> >>> >>> Hi Hiroki Mori, >>> >>> Oh I see, got it, thanks for the explanation! >>> >>> Best regards, >>> Archimedes >>> >>> >>>> >>>> ----- Original Message ----- >>>> >>>> From: "Archimedes Gaviola" <archimedes.gaviola@gmail.com> >>>> To: "freebsd-mips@freebsd.org" <freebsd-mips@freebsd.org> >>>> Date: 2022/08/18 木 21:38 >>>> Subject: Ralink RT3050F >>>> >>>> >>>> Hi, >>>> >>>> I have successfully compiled an RT3050F SoC kernel image with FreeBSD >>>> 11.4-RELEASE by following this reference here >>>> https://wiki.freebsd.org/mips/RT3052F. However, I want to know how >>>> this value 0x80800000 is derived for the tftpboot? My generated image entry >>>> point value address is 80001100. >>>> >>>> root@freebsd114:/usr/obj/mips.mipsel/usr/src/sys/RT305X # readelf -h >>>> kernel | grep 'Entry point address:' >>>> Entry point address: 0x80001100 >>>> >>>> Thanks and best regards, >>>> Archimedes >>>> >>>> -- WBW ------- Rybalko Aleksandr <ray@dlink.ua> aka Alex RAY <ray@ddteam.net> D-Link.ua