Re: FreeBSD 13.0-STABLE on Pinephone
- In reply to: Crystal Kolipe : "FreeBSD 13.0-STABLE on Pinephone"
- Go to: [ bottom of page ] [ top of archives ] [ this month ]
Date: Sat, 15 Jan 2022 08:04:48 UTC
On Sat, 15 Jan 2022 at 01:21, Crystal Kolipe <kolipe.c@exoticsilicon.com> wrote: > Hi, > > I installed FreeBSD 13.0-STABLE on a Pinephone 1.2 for testing, and > thought that the dmesg output would be of interest to the list: > > ---<<BOOT>>--- > WARNING: Cannot find freebsd,dts-version property, cannot check DTB > compliance > Copyright (c) 1992-2021 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 13.0-STABLE #0 stable/13-n248759-3684bb89d52: Thu Dec 30 03:49:13 > UTC 2021 > root@releng3.nyi.freebsd.org:/usr/obj/usr/src/arm64.aarch64/sys/GENERIC > arm64 > FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git > llvmorg-13.0.0-0-gd7b669b3a303) > VT: init without driver. > module firmware already present! > real memory = 3221004288 (3071 MB) > avail memory = 3118305280 (2973 MB) > Starting CPU 1 (1) > Starting CPU 2 (2) > Starting CPU 3 (3) > FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs > random: unblocking device. > random: entropy device external interface > MAP f8f2b000 mode 2 pages 4 > MAP f8f30000 mode 2 pages 4 > MAP fdf60000 mode 2 pages 16 > kbd0 at kbdmux0 > ofwbus0: <Open Firmware Device Tree> > clk_fixed0: <Fixed clock> on ofwbus0 > clk_fixed1: <Fixed clock> on ofwbus0 > simplebus0: <Flattened device tree simple bus> on ofwbus0 > regfix0: <Fixed Regulator> on ofwbus0 > regfix1: <Fixed Regulator> on ofwbus0 > psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 > rtc0: <Allwinner RTC> mem 0x1f00000-0x1f003ff irq 58,59 on simplebus0 > rtc0: registered as a time-of-day clock, resolution 1.000000s > ccu_a64ng0: <Allwinner A64 Clock Control Unit NG> mem 0x1c20000-0x1c203ff > on simplebus0 > ccu_sun8i_r0: <Allwinner SUN8I_R Clock Control Unit NG> mem > 0x1f01400-0x1f014ff on simplebus0 > gic0: <ARM Generic Interrupt Controller> mem > 0x1c81000-0x1c81fff,0x1c82000-0x1c83fff,0x1c84000-0x1c85fff,0x1c86000-0x1c87fff > irq 53 on simplebus0 > gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 224 > aw_r_intc_gicp0: <Allwinner R INTC> mem 0x1f00c00-0x1f00fff irq 60 on > simplebus0 > gpio0: <Allwinner GPIO/Pinmux controller> mem 0x1c20800-0x1c20bff irq > 24,25,26 on simplebus0 > gpiobus0: <OFW GPIO bus> on gpio0 > iichb0: <Allwinner Integrated I2C Bus Controller> mem 0x1c2ac00-0x1c2afff > irq 40 on simplebus0 > iicbus0: <OFW I2C bus> on iichb0 > iichb1: <Allwinner Integrated I2C Bus Controller> mem 0x1c2b000-0x1c2b3ff > irq 41 on simplebus0 > iicbus1: <OFW I2C bus> on iichb1 > iichb2: <Allwinner Integrated I2C Bus Controller> mem 0x1c2b400-0x1c2b7ff > irq 42 on simplebus0 > iicbus2: <OFW I2C bus> on iichb2 > gpio1: <Allwinner GPIO/Pinmux controller> mem 0x1f02c00-0x1f02fff irq 63 > on simplebus0 > gpiobus1: <OFW GPIO bus> on gpio1 > generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0 > Timecounter "ARM MPCore Timecounter" frequency 24000000 Hz quality 1000 > Event timer "ARM MPCore Eventtimer" frequency 24000000 Hz quality 1000 > a10_timer0: <Allwinner timer> mem 0x1c20c00-0x1c20c2b irq 8,9 on simplebus0 > Timecounter "a10_timer timer0" frequency 24000000 Hz quality 2000 > aw_syscon0: <Allwinner syscon> mem 0x1c00000-0x1c00fff on simplebus0 > rtc1: <MAX77620 RTC> at addr 0xd0 irq 69 on iicbus1 > rtc1: Error when reading reg 0x02, rv: 3 > rtc1: Failed to configure RTC > device_attach: rtc1 attach returned 5 > rtc1: <MAX77620 RTC> at addr 0xd0 irq 69 on iicbus1 > rtc1: Error when reading reg 0x02, rv: 3 > rtc1: Failed to configure RTC > device_attach: rtc1 attach returned 5 > aw_sid0: <Allwinner Secure ID Controller> mem 0x1c14000-0x1c143ff on > simplebus0 > rtc1: <MAX77620 RTC> at addr 0xd0 irq 69 on iicbus1 > rtc1: Error when reading reg 0x02, rv: 3 > rtc1: Failed to configure RTC > device_attach: rtc1 attach returned 5 > mmc_pwrseq0: <MMC Simple Power sequence> on ofwbus0 > awusbphy0: <Allwinner USB PHY> mem > 0x1c19400-0x1c19413,0x1c1a800-0x1c1a803,0x1c1b800-0x1c1b803 on simplebus0 > rtc1: <MAX77620 RTC> at addr 0xd0 irq 69 on iicbus1 > rtc1: Error when reading reg 0x02, rv: 3 > rtc1: Failed to configure RTC > device_attach: rtc1 attach returned 5 > iichb3: <Allwinner RSB> mem 0x1f03400-0x1f037ff irq 64 on simplebus0 > iicbus3: <OFW I2C bus> on iichb3 > axp8xx_pmu0: <X-Powers AXP803 Power Management Unit> at addr 0x746 irq 70 > on iicbus3 > axp8xx_pmu0: cannot allocate resources for device > device_attach: axp8xx_pmu0 attach returned 6 > cpulist0: <Open Firmware CPU Group> on ofwbus0 > cpu0: <Open Firmware CPU> on cpulist0 > cpufreq_dt0: <Generic cpufreq driver> on cpu0 > cpufreq_dt0: no regulator for cpu@0 > device_attach: cpufreq_dt0 attach returned 6 > cpu1: <Open Firmware CPU> on cpulist0 > cpufreq_dt1: <Generic cpufreq driver> on cpu1 > cpufreq_dt1: no regulator for cpu@1 > device_attach: cpufreq_dt1 attach returned 6 > cpu2: <Open Firmware CPU> on cpulist0 > cpufreq_dt2: <Generic cpufreq driver> on cpu2 > cpufreq_dt2: no regulator for cpu@2 > device_attach: cpufreq_dt2 attach returned 6 > cpu3: <Open Firmware CPU> on cpulist0 > cpufreq_dt3: <Generic cpufreq driver> on cpu3 > cpufreq_dt3: no regulator for cpu@3 > device_attach: cpufreq_dt3 attach returned 6 > pmu0: <Performance Monitoring Unit> irq 0,1,2,3 on ofwbus0 > a31dmac0: <Allwinner DMA controller> mem 0x1c02000-0x1c02fff irq 10 on > simplebus0 > aw_mmc0: <Allwinner Integrated MMC/SD controller> mem 0x1c0f000-0x1c0ffff > irq 14 on simplebus0 > aw_mmc1: <Allwinner Integrated MMC/SD controller> mem 0x1c10000-0x1c10fff > irq 15 on simplebus0 > aw_mmc2: <Allwinner Integrated MMC/SD controller> mem 0x1c11000-0x1c11fff > irq 16 on simplebus0 > musbotg0: <Allwinner USB DRD> mem 0x1c19000-0x1c193ff irq 19 on simplebus0 > musbotg0: setting phy mode 3 > usbus0: Dynamic FIFO sizing detected, assuming 16Kbytes of FIFO RAM > usbus0 on musbotg0 > ehci0: <Generic EHCI Controller> mem 0x1c1a000-0x1c1a0ff irq 20 on > simplebus0 > usbus1: EHCI version 1.0 > usbus1 on ehci0 > ohci0: <Generic OHCI Controller> mem 0x1c1a400-0x1c1a4ff irq 21 on > simplebus0 > usbus2 on ohci0 > ehci1: <Generic EHCI Controller> mem 0x1c1b000-0x1c1b0ff irq 22 on > simplebus0 > usbus3: EHCI version 1.0 > usbus3 on ehci1 > ohci1: <Generic OHCI Controller> mem 0x1c1b400-0x1c1b4ff irq 23 on > simplebus0 > usbus4 on ohci1 > gpioc0: <GPIO controller> on gpio0 > aw_thermal0: <Allwinner Thermal Sensor Controller> mem 0x1c25000-0x1c250ff > irq 34 on simplebus0 > uart0: <16750 or compatible> mem 0x1c28000-0x1c283ff irq 35 on > simplebus0uart0: console (115384,n,8,1) > uart1: <16750 or compatible> mem 0x1c28400-0x1c287ff irq 36 on simplebus0 > uart2: <16750 or compatible> mem 0x1c28c00-0x1c28fff irq 38 on simplebus0 > iicbus0: <unknown card> at addr 0xba > iic0: <I2C generic I/O> on iicbus0 > iicbus1: <unknown card> at addr 0x3c > iicbus1: <unknown card> at addr 0x90 > rtc1: <MAX77620 RTC> at addr 0xd0 irq 69 on iicbus1 > rtc1: Error when reading reg 0x02, rv: 3 > rtc1: Failed to configure RTC > device_attach: rtc1 attach returned 5 > iic1: <I2C generic I/O> on iicbus1 > iic2: <I2C generic I/O> on iicbus2 > pwm0: <Allwinner PWM> mem 0x1f03800-0x1f03bff on simplebus0 > pwmbus0: <OFW PWM bus> on pwm0 > pwmc0: <PWM Control> channel 0 on pwmbus0 > gpioc1: <GPIO controller> on gpio1 > axp8xx_pmu0: <X-Powers AXP803 Power Management Unit> at addr 0x746 irq 70 > on iicbus3 > axp8xx_pmu0: cannot allocate resources for device > device_attach: axp8xx_pmu0 attach returned 6 > iic3: <I2C generic I/O> on iicbus3 > aw_wdog0: <Allwinner A31 Watchdog> mem 0x1c20ca0-0x1c20cbf irq 65 on > simplebus0 > gpioled0: <GPIO LEDs> on ofwbus0 > armv8crypto0: <AES-CBC,AES-XTS,AES-GCM> > cpufreq_dt0: <Generic cpufreq driver> on cpu0 > cpufreq_dt0: no regulator for cpu@0 > device_attach: cpufreq_dt0 attach returned 6 > cpufreq_dt1: <Generic cpufreq driver> on cpu1 > cpufreq_dt1: no regulator for cpu@1 > device_attach: cpufreq_dt1 attach returned 6 > cpufreq_dt2: <Generic cpufreq driver> on cpu2 > cpufreq_dt2: no regulator for cpu@2 > device_attach: cpufreq_dt2 attach returned 6 > cpufreq_dt3: <Generic cpufreq driver> on cpu3 > cpufreq_dt3: no regulator for cpu@3 > device_attach: cpufreq_dt3 attach returned 6 > Timecounters tick every 1.000 msec > CPU 0: ARM Cortex-A53 r0p4 affinity: 0 > Cache Type = <64 byte D-cacheline,64 byte > I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG> > Instruction Set Attributes 0 = <CRC32,SHA2,SHA1,AES+PMULL> > Instruction Set Attributes 1 = <> > Processor Features 0 = <AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32> > Processor Features 1 = <> > Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit > ASID,1TB PA> > Memory Model Features 1 = <8bit VMID> > Memory Model Features 2 = <32bit CCIDX,48bit VA> > Debug Features 0 = <DoubleLock,2 CTX BKPTs,4 Watchpoints,6 > Breakpoints,PMUv3,Debugv8> > Debug Features 1 = <> > Auxiliary Features 0 = <> > Auxiliary Features 1 = <> > AArch32 Instruction Set Attributes 5 = <CRC32,SHA2,SHA1,AES+VMULL,SEVL> > AArch32 Media and VFP Features 0 = <FPRound,FPSqrt,FPDivide,DP VFPv3+v4,SP > VFPv3+v4,AdvSIMD> > AArch32 Media and VFP Features 1 = <SIMDFMAC,FPHP DP Conv,SIMDHP SP > Conv,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ> > CPU 1: ARM Cortex-A53 r0p4 affinity: 1 > CPU 2: ARM Cortex-A53 r0p4 affinity: 2 > CPU 3: ARM Cortex-A53 r0p4 affinity: 3 > Release APs...done > usbus0: 480Mbps High Speed USB v2.0 > usbus1: 480Mbps High Speed USB v2.0 > usbus2: 12Mbps Full Speed USB v1.0 > usbus3: 480Mbps High Speed USB v2.0 > usbus4: 12Mbps Full Speed USB v1.0 > Trying to mount root from ufs:/dev/ufs/rootfs [rw]... > ugen0.1: <Mentor Graphics OTG Root HUB> at usbus0 > Root mount waiting for:uhub0ugen2.1: <Generic OHCI root HUB> at usbus2 > ugen1.1: <Generic EHCI root HUB> at usbus1 > on usbus0 > uhub0: <Mentor Graphics OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on > usbus0 > usbus0uhub1 on usbus2 > usbus1uhub1: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on > usbus2 > usbus2ugen3.1: <Generic EHCI root HUB> at usbus3 > usbus3uhub2 usbus4 on usbus1 > > uhub2: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 > uhub3 on usbus3 > uhub3: <Generic EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus3 > ugen4.1: <Generic OHCI root HUB> at usbus4 > uhub4 on usbus4 > uhub4: <Generic OHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus4 > uhub1: 1 port with 1 removable, self powered > uhub4: 1 port with 1 removable, self powered > uhub0: 1 port with 1 removable, self powered > mmc0: <MMC/SD bus> on aw_mmc2 > mmc0: Failed to set VCCQ for card at relative address 2 > mmcsd0: 31GB <MMCHC DA4032 0.1 SN FF342515 MFG 06/2020 by 69 0x0000> at > mmc0 52.0MHz/8bit/4096-block > mmcsd0boot0: 4MB partition 1 at mmcsd0 > mmcsd0boot1: 4MB partition 2 at mmcsd0 > mmcsd0rpmb: 17MB partition 3 at mmcsd0 > mmc1: <MMC/SD bus> on aw_mmc1 > mmc1: No compatible cards found on bus > aw_mmc1: Spurious interrupt - no active request, rint: 0x00000004 > > uhub2: 1 port with 1 removable, self powered > uhub3: 1 port with 1 removable, self powered > mountroot: waiting for device /dev/ufs/rootfs... > Dual Console: Serial Primary, Video Secondary > Setting hostuuid: 30633239-6439-6162-3062-303436373435. > Setting hostid: 0x09ffad61. > /etc/rc: WARNING: $zfskeys_enable is not set properly - see rc.conf(5). > Starting file system checks: > /dev/ufs/rootfs: FILE SYSTEM CLEAN; SKIPPING CHECKS > /dev/ufs/rootfs: clean, 6670786 free (26 frags, 833845 blocks, 0.0% > fragmentation) > Mounting local filesystems:. > Setting hostname: generic. > ELF ldconfig path: /lib /usr/lib /usr/lib/compat > Setting up harvesting: > [UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,[NET_ETHER],NET_TUN,MOUSE,KEYBOARD,ATTACH,CACHED > Feeding entropy: . > Autoloading module: pwm_backlight > warning: KLD '/boot/kernel/backlight.ko' is newer than the linker.hints > file > pwm_backlight0: <PWM Backlight> on ofwbus0 > pwm_backlight0: No power-supply property > device_attach: pwm_backlight0 attach returned 6 > lo0: link state changed to UP > Starting Network: lo0. > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 > options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6> > inet6 ::1 prefixlen 128 > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 > inet 127.0.0.1 netmask 0xff000000 > groups: lo > nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> > Starting devd. > add host 127.0.0.1: gateway lo0 fib 0: route already in table > add host ::1: gateway lo0 fib 0: route already in table > add net fe80::: gateway ::1 > add net ff02::: gateway ::1 > add net ::ffff:0.0.0.0: gateway ::1 > add net ::0.0.0.0: gateway ::1 > Updating /var/run/os-release done. > Creating and/or trimming log files. > Clearing /tmp (X related). > Updating motd:. > Starting syslogd. > Mounting late filesystems:. > Performing sanity check on sshd configuration. > Starting sshd. > Starting cron. > Starting background file system checks in 60 seconds. > > Fri Jan 1 00:04:48 UTC 2010 > > FreeBSD/arm64 (generic) (ttyu0) > > login: root > Password: > Jan 1 00:04:50 generic login[835]: ROOT LOGIN (root) ON ttyu0 > > Hi, Nice! Can you please share with us what components are working? For example, wi-fi works? Works the baseband router? Can you connect to cellular network? And, it would be amazing if you share with us the steps to make the installation :) Bye!