Re: [iwlwifi] ipv6 connection problem
- Reply: Shawn Webb : "Re: [iwlwifi] ipv6 connection problem"
- In reply to: Shawn Webb : "Re: [iwlwifi] ipv6 connection problem"
- Go to: [ bottom of page ] [ top of archives ] [ this month ]
Date: Sat, 13 Aug 2022 20:49:34 UTC
Hello Shawn! I've tested your config: --- wlans_iwlwifi0="wlan0" create_args_wlan0="wlanmode sta regdomain ETSI country PT" ifconfig_wlan0_ipv6="inet6 accept_rtadv" ifconfig_wlan0="WPA DHCP" rtsold_enable="YES" --- and no carrier. Think we have to wait a little more and see if people that use ifwwifi driver do some tests on ipv6. Thanks, Shawn Webb <shawn.webb@hardenedbsd.org> escreveu no dia sábado, 13/08/2022 à(s) 21:21: > On Sun, Aug 07, 2022 at 06:16:20PM +0100, Nuno Teixeira wrote: > > Hello, > > > > Due to ISP changes I was forced to use ipv6 on my re0 ethernet so I can > > have a funcional internet. > > > > Now I'm trying to get ipv6 on iwlwifi (AX201) with /etc/rc.conf: > > --- > > wlans_iwlwifi0="wlan0" > > create_args_wlan0="wlanmode sta regdomain ETSI country PT" > > ifconfig_wlan0_ipv6="inet6 accept_rtadv" > > ifconfig_wlan0="WPA SYNCDHCP" > > rtsold_enable="YES" > > --- > > but wpa_supplicant doesn't connect after trying for some seconds. > > > > How do I obtain more details to help showing my problem? > > I've tried "wpa_supplicant_flags="-f /var/log/wpa.log" without success. > > Caveat: the last time I used the iwlwifi driver was somewhere between > one and two months ago, during which time there have been several > changes in src related to wifi/linuxkpi stuff. > > Hardware: Dell Precision 7550, BIOS revision 1.13.0 > > Dual stack IPv4+IPv6 worked for me that last time I used iwlwifi. > Here's my relevant configs: > > ==== begin rc.conf ==== > ifconfig_em0_ipv6="inet6 accept_rtadv" > ifconfig_em0="DHCP" > > #wlans_iwlwifi0="wlan0" > create_args_wlan0="wlanmode sta" > wlandebug_wlan0="+state +crypto +node +auth +assoc +dot1xsm +wpa" > ifconfig_wlan0="WPA DHCP" > ifconfig_wlan0_ipv6="inet6 accept_rtadv" > ==== end rc.conf ==== > > ==== begin `pciconf -lv` ==== > iwlwifi0@pci0:0:20:3: class=0x028000 rev=0x00 hdr=0x00 vendor=0x8086 > device=0x06f0 subvendor=0x8086 subdevice=0x4070 > vendor = 'Intel Corporation' > device = 'Comet Lake PCH CNVi WiFi' > ==== end `pciconf -lv` ==== > > ==== begin dmesg.boot ==== > 27] iwlwifi0: successfully loaded firmware image > 'iwlwifi-QuZ-a0-hr-b0-71.ucode' > [27] iwlwifi0: api flags index 2 larger than supported by driver > [27] iwlwifi0: TLV_FW_FSEQ_VERSION: FSEQ Version: 89.3.35.37 > [27] iwlwifi0: loaded firmware version 71.058653f6.0 QuZ-a0-hr-b0-71.ucode > op_mode iwlmvm > [27] iwlwifi0: Detected Intel(R) Wi-Fi 6 AX201 160MHz, REV=0x351 > [28] iwlwifi0: Detected RF HR B3, rfid=0x10a100 > [28] iwlwifi0: base HW address: [redacted] > ==== end dmesg.boot ==== > > Hopefully this helps. But this is all the info I've got. Please let me > know if you have any questions or comments. > > Thanks, > > -- > Shawn Webb > Cofounder / Security Engineer > HardenedBSD > > > https://git.hardenedbsd.org/hardenedbsd/pubkeys/-/raw/master/Shawn_Webb/03A4CBEBB82EA5A67D9F3853FF2E67A277F8E1FA.pub.asc > -- Nuno Teixeira FreeBSD Committer (ports)