Re: Failover Mode between ether/wlan panics
- In reply to: Mario Lobo : "Re: Failover Mode between ether/wlan panics"
- Go to: [ bottom of page ] [ top of archives ] [ this month ]
Date: Mon, 01 Aug 2022 16:55:49 UTC
On Mon, Aug 1, 2022 at 1:30 PM Mario Lobo <lobo@bsd.com.br> wrote: > > > On Mon, Aug 1, 2022, 11:01 Nuno Teixeira <eduardo@freebsd.org> wrote: > >> Hi, >> >> Something is wrong about getting ether and wlan mac adresses. >> dmesg shows the same address: >> --- >> iwlwifi0: Detected Intel(R) Wi-Fi 6 AX201 160MHz, REV=0x351 >> iwlwifi0: base HW address: 6c:6a:77:df:09:21 >> (...) >> re0: <RealTek 8168/8111 B/C/CP/D/DP/E/F/G PCIe Gigabit Ethernet> port >> 0x3000-0x30ff mem 0xb4204000-0xb4204fff,0xb4200000-0xb4203fff at device 0.0 >> on pci3 >> re0: Ethernet address: 6c:6a:77:df:09:21 >> --- >> and ifconfig shows: >> --- >> re0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 >> >> options=8209b<RXCSUM,TXCSUM,VLAN_MTU,VLAN_HWTAGGING,VLAN_HWCSUM,WOL_MAGIC,LINKSTATE> >> ether 6c:6a:77:df:09:21 >> media: Ethernet autoselect (100baseTX <full-duplex>) >> status: active >> nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> >> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 >> options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6> >> inet6 ::1 prefixlen 128 >> inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2 >> inet 127.0.0.1 netmask 0xff000000 >> groups: lo >> nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> >> wlan0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu >> 1500 >> ether 6c:6a:77:df:09:21 >> inet 192.168.1.74 netmask 0xffffff00 broadcast 192.168.1.255 >> groups: wlan >> ssid MEO-3637C0 channel 1 (2412 MHz 11g) bssid 00:06:91:36:37:c0 >> regdomain ETSI country PT authmode WPA2/802.11i privacy ON >> deftxkey UNDEF AES-CCM 2:128-bit txpower 30 bmiss 7 scanvalid 60 >> protmode CTS wme roaming MANUAL >> parent interface: iwlwifi0 >> media: IEEE 802.11 Wireless Ethernet OFDM/24Mbps mode 11g >> status: associated >> nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> >> --- >> >> I disabled wireless at bios and same mac address for ethernet. >> I don't see a possibility of both cards sharing same mac address... >> >> Cheers >> >> Mario Lobo <lobo@bsd.com.br> escreveu no dia segunda, 1/08/2022 à(s) >> 13:15: >> >>> >>> On Sun, Jul 31, 2022, 21:05 Nuno Teixeira <eduardo@freebsd.org> wrote: >>> >>>> Hello, >>>> >>>> I'm trying to setup a failover mode ethernet/wireless as shown in >>>> https://docs.freebsd.org/en/books/handbook/book/#networking-lagg-wired-and-wireless >>>> and I got a panic. >>>> >>>> /etc/rc.conf: >>>> --- >>>> ifconfig_re0="ether <wlan0 mac address>" >>>> wlans_iwlwifi0="wlan0" >>>> ifconfig_wlan0="WPA" >>>> create_args_wlan0="country PT" >>>> cloned_interfaces="lagg0" >>>> ifconfig_lagg0="up laggproto failover laggport re0 laggport wlan0 DHCP" >>>> --- >>>> >>>> Any ideas of what's wrong? >>>> BTW, no kernel dump and I have dumpdev="AUTO" in /etc/rc.conf... >>>> >>>> Thanks in advance, >>>> Nuno Teixeira >>>> >>> >>> Hi. >>> >>> For this to work, you'll have to clone your wifi MAC to your eth MAC. >>> >> > Your lagg0 interface is missing. > >> Here is my ifconfig: [~]>ifconfig re0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 options=80088<VLAN_MTU,VLAN_HWCSUM,LINKSTATE> ether f8:94:c2:26:f3:54 hwaddr fc:45:96:fb:3d:82 media: Ethernet autoselect (1000baseT <full-duplex>) status: active nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6> inet6 ::1 prefixlen 128 inet6 fe80::1%lo0 prefixlen 64 scopeid 0x2 inet 127.0.0.1 netmask 0xff000000 groups: lo nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> vboxnet0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500 ether 0a:00:27:00:00:00 media: Ethernet autoselect status: active nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> wlan0: flags=8c43<UP,BROADCAST,RUNNING,OACTIVE,SIMPLEX,MULTICAST> metric 0 mtu 1500 ether f8:94:c2:26:f3:54 groups: wlan ssid "" channel 1 (2412 MHz 11g) regdomain FCC country US authmode WPA1+WPA2/802.11i privacy MIXED deftxkey UNDEF powersavemode CAM powersavesleep 100 txpower 30 bmiss 10 scanvalid 60 protmode CTS wme roaming MANUAL parent interface: iwm0 media: IEEE 802.11 Wireless Ethernet autoselect (autoselect) status: no carrier nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> lagg0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 ether f8:94:c2:26:f3:54 inet6 fe80::fa94:c2ff:fe26:f354%lagg0 prefixlen 64 scopeid 0x5 inet 10.17.12.215 netmask 0xffffff00 broadcast 10.17.12.255 laggproto failover lagghash l2,l3,l4 laggport: re0 flags=5<MASTER,ACTIVE> laggport: wlan0 flags=0<> groups: lagg media: Ethernet autoselect status: active nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> And here is my rc.conf: ifconfig_wlan0="mode autoselect WPA powersave up" wlans_iwm0="wlan0" wpa_supplicant_enable="YES" wpa_supplicant_program="/usr/local/sbin/wpa_supplicant" wpa_supplicant_flags="-dd" ifconfig_re0="media 1000baseTX mediaopt full-duplex up" ifconfig_re0="ether f8:94:c2:26:f3:54" ifconfig_lagg0="up laggproto failover laggport re0 laggport wlan0 DHCP" cloned_interfaces="lagg0" -- Mario Lobo http://www.mallavoodoo.com.br FreeBSD since version 2.2.8 [not Pro-Audio.... YET!!]