Re: RPI2 Model B not booting with 13.2 release?
- In reply to: Luís_Henriques : "Re: RPI2 Model B not booting with 13.2 release?"
- Go to: [ bottom of page ] [ top of archives ] [ this month ]
Date: Tue, 30 May 2023 22:13:02 UTC
On May 30, 2023, at 13:27, Luís Henriques <henrix@camandro.org> wrote: > Mark Millard <marklmi@yahoo.com> writes: > >> On May 30, 2023, at 09:10, Luís Henriques <henrix@camandro.org> wrote: >> >>> I'm probably doing something wrong, but I've run out of ideas. >>> >>> This is my first attempt to install FreeBSD on my old RPI2. >> >> Which type of RPi2B? (There was a technically confusing >> marking-naming used for a significant technical change.) >> >> RPi2B v1.1: a cortex-A7 implementation of armv7, no aarch64 support >> RPi2B v1.2: a cortex-a53 implementation of aarch64, plus aarch32/armv7 >> >> You did not supply enough information for me to tell >> which. > > You're right, of course. Sorry, and thanks for your help. > > So, my RPi2b is a v1.1. > >>> So, after >>> dd'ing the 13.2 (release) SD image >> >> v1.1 would need: >> >> FreeBSD-13.2-RELEASE-arm-armv7-GENERICSD.img.xz >> >> instead of FreeBSD-13.2-RELEASE-arm64-aarch64-RPI.img.xz >> >> v1.2 would need : >> >> FreeBSD-13.2-RELEASE-arm64-aarch64-RPI.img.xz >> >> instead of: FreeBSD-13.2-RELEASE-arm-armv7-GENERICSD.img.xz > > Oh! Interesting. And confusing, because I didn't actually used *any* of > the above. Instead, I've tried: > > FreeBSD-13.2-RELEASE-arm-armv6-RPI-B.img.xz > > That was the one that seemed to make more sense to me. I am now > downloading the image you've suggested and I'll give it a try in a bit. > Thanks a lot, Mark! > > And for completeness, the (working) image I tried for 12.4 was: > > FreeBSD-12.4-RELEASE-arm-armv6-RPI-B.img.xz There are/were: FreeBSD-12.*-RELEASE-arm-armv7-RPI2.img.xz but there was not a: FreeBSD-13.*-RELEASE-arm-armv7-RPI2.img.xz For 13.*: There are/were: FreeBSD-13.*-RELEASE-arm-armv7-GENERICSD.img.xz (It also supports a non-RPi* board, not just the RPi2B v1.1 board. By dd'ing in uboot related materials, more armv7 boards are usable as well.) armv6 predates all the RPi2B variants and later: it was from the original RPiB model. > /me goes try the new image. > > Cheers, > -- > Luís > >> You did not supply enough information for me to tell >> which *.img* file you downloaded and tried to use. >> >> FYI: >> >> FreeBSD-13.2-RELEASE-arm-armv7-GENERICSD.img.xz has just >> the one .dtb file: bcm2709-rpi-2-b.dtb (the one for the >> v1.1 RPi2B). (If it also had bcm2710-rpi-2-b.dtb, then >> both variants would boot. Similarly for other >> bcm2710-rpi-*.dtb files enabling some other RPi* variants >> to boot as armv7 instead of aarch64.) >> >> By conttrast, adding bcm2709-rpi-2-b.dtb to >> FreeBSD-13.2-RELEASE-arm64-aarch64-RPI.img.xz would >> not make it work for a RPi2B v1.1 . >> >>> and connecting the serial USB, I got no >>> output at all. From the HDMI interface, I see a colourful screen, but >>> nothing else. The same happens with 13.1. And only 12.4 seems to boot >>> this device: >>> >>> # uname -a >>> FreeBSD generic 12.4-STABLE FreeBSD 12.4-STABLE r373082 GENERIC arm >>> >>> Is this model not supposed to boot anymore and I just couldn't find any >>> information about it? Or am I doing something wrong? === Mark Millard marklmi at yahoo.com