Re: Raspberry Pi POE+ hat overlay
- Reply: Nuno Teixeira : "Re: Raspberry Pi POE+ hat overlay"
- In reply to: Doug Rabson : "Re: Raspberry Pi POE+ hat overlay"
- Go to: [ bottom of page ] [ top of archives ] [ this month ]
Date: Wed, 17 May 2023 13:08:11 UTC
(...) I was meant using 13.2 not 12.3 :) Doug Rabson <dfr@rabson.org> escreveu no dia quarta, 17/05/2023 à(s) 13:47: > I'm not sure about 12.3 either - you could try with 13.2 and see if that > makes a difference. > > On Wed, 17 May 2023 at 13:45, Nuno Teixeira <eduardo@freebsd.org> wrote: > >> Hey, >> >> Ok. I'm new to rpi4 and arm in general but tomorrow I will force >> 'arm_freq=1800' again just to see it it crashes again. >> I will check too what values linux shows. >> >> I don't know if firmware/uboot version included in 12.3 supports this >> feature. >> >> Cheers, >> >> Doug Rabson <dfr@rabson.org> escreveu no dia quarta, 17/05/2023 à(s) >> 13:11: >> >>> Hi Nuno, >>> >>> I'm not sure where to start - I just happened to notice in the >>> documentation here: >>> https://www.raspberrypi.com/documentation/computers/config_txt.html >>> that the cpu frequency Pi4B R1.4 was listed as 1800 if arm_boot=1 so I >>> tried it. >>> >>> Doug. >>> >>> >>> >>> On Wed, 17 May 2023 at 11:11, Nuno Teixeira <eduardo@freebsd.org> wrote: >>> >>>> Hello Doug, >>>> >>>> I have too a 1.5 rpi but arm_boost=1 isn't doing anything, htop shows >>>> 1500Mhz when doing something intensive. >>>> I'm running 13.2 stable >>>> >>>> Do I missing something? >>>> >>>> Could you take a look at my setup? >>>> >>>> Thanks, >>>> >>>> Doug Rabson <dfr@rabson.org> escreveu no dia terça, 16/05/2023 à(s) >>>> 17:19: >>>> >>>>> >>>>> On Sat, 13 May 2023 at 13:45, Doug Rabson <dfr@rabson.org> wrote: >>>>> >>>>>> I was able to build an updated rpi-firmware port based on 1.20210805 >>>>>> and this boots successfully on pi400 as well as rpi4. With this, I can load >>>>>> the rpi-poe-plus overlay and I just need to try and reverse engineer the >>>>>> undocumented mailbox API by reading the Linux code. >>>>>> >>>>> >>>>> I have a first approximation of a fan driver which works with the >>>>> 1.20210805 firmware (actually, I substituted rpi-poe-plus.dtbo from >>>>> 1.20210831 which just changes the fan levels for the POE+). I'm testing >>>>> with an rpi4B rev 1.5 with 'make -j4 buildworld' and the fan is keeping the >>>>> cpu temperature below 65 degrees which is nice, especially since I set >>>>> arm_boost=1 in config.txt which boosts the cpu frequency up to 1800 for >>>>> this board. >>>>> >>>>> Does anyone have a pointer to the problem with firmware later than >>>>> 20210805? Would it make any kind of sense to try to get the fix into >>>>> releng/13.2 as an errata? >>>>> >>>>> >>>> >>>> -- >>>> Nuno Teixeira >>>> FreeBSD Committer (ports) >>>> >>> >> >> -- >> Nuno Teixeira >> FreeBSD Committer (ports) >> > -- Nuno Teixeira FreeBSD Committer (ports)