Re: git: 1dfcff294e44 - main - release: increase IMAGE_SIZE for arm, arm64, riscv [odd alignment for SBC images]
- Reply: Mark Millard : "Re: git: 1dfcff294e44 - main - release: increase IMAGE_SIZE for arm, arm64, riscv [odd alignment for SBC images]"
- In reply to: Mark Millard : "Re: git: 1dfcff294e44 - main - release: increase IMAGE_SIZE for arm, arm64, riscv [odd alignment for SBC images]"
- Go to: [ bottom of page ] [ top of archives ] [ this month ]
Date: Sat, 30 Jul 2022 03:11:23 UTC
On 2022-Jul-29, at 19:56, Mark Millard <marklmi@yahoo.com> wrote: > On 2022-Jul-29, at 13:49, Glen Barber <gjb@FreeBSD.org> wrote: > >> On Wed, Jul 20, 2022 at 10:08:20AM -0700, Mark Millard wrote: >>> Would it seem appropriate to use a week (this week?) to do all >>> the snapshot builds with the builders all set to have >>> kern.geom.part.mbr.enforce_chs=0 and see what breaks, if anything? >>> (Sort of a snapshot exp run.) >>> >>> More than just the SBC images might be involved for >>> kern.geom.part.mbr.enforce_ch consequences, for all I know. >>> >> >> Hey, Mark. >> >> New snapshots for 13 and 14 are up now. Is it possible for you to check >> if the issues you had run into are indeed resolved, after setting >> kern.geom.part.mbr.enforce_chs=0 on the builders? >> > > Well, it is a mix, I think (unsure). > > I started with: > > # dd if=FreeBSD-13.1-STABLE-arm64-aarch64-RPI-20220729-db2eff1cff8-251976.img of=/dev/da0 conv=sync,fsync bs=1m status=progress > 5222957056 bytes (5223 MB, 4981 MiB) transferred 21.027s, 248 MB/s > 5120+0 records in > 5120+0 records out > 5368709120 bytes transferred in 21.816899 secs (246080301 bytes/sec) > > I plugged the USB3 SSD into an old 8 GiByte RPi4B and it booted. > > . . . > Starting file system checks: > /dev/ufs/rootfs: FILE SYSTEM CLEAN; SKIPPING CHECKS > /dev/ufs/rootfs: clean, 499417 free (1153 frags, 62283 blocks, 0.1% fragmentation) > Growing root partition to fill device > random: randomdev_wait_until_seeded unblock wait > random: randomdev_wait_until_seeded unblock wait > random: unblocking device. > GEOM_PART: ufs/rootfs was automatically resized. > Use `gpart commit ufs/rootfs` to save changes or `gpart undo ufs/rootfs` to revert them. > da0s2 resized > super-block backups (for fsck_ffs -b #) at: > 11524224, 12804672, 14085120, 15365568, 16646016, 17926464, 19206912, > . . . > > But, after logging in: > > root@generic:~ # gpart show > => 63 468862065 da0 MBR (224G) > 63 1985 - free - (993K) > 2048 102400 1 fat32lba [active] (50M) > 104448 468757680 2 freebsd (224G) > > root@generic:~ # gpart show -p > => 63 468862065 da0 MBR (224G) > 63 1985 - free - (993K) > 2048 102400 da0s1 fat32lba [active] (50M) > 104448 468757680 da0s2 freebsd (224G) > > So 1985 and 2048 are there, as intended. > > But no explicit da0s2 BSD or da0s2a freebsd-ufs shows up > in gpart show's output. > > I wonder if this is because of a lack of a distinct > starting offset vs. the BSD. For example, the old 2016 > and 2079 alignment had showed: > > => 0 468757737 da0s2 BSD (224G) > 0 57 - free - (29K) > 57 468757680 da0s2a freebsd-ufs (224G) > > where the 57 was, appearently, for alignment. May be now > the distance from the da0s2 to da0s2a is zero and so > BSD and its contained da0s2a is not now shown? > > I've yet to try the 14-CURRENT. > It did not survive a simple reboot test: . . . FreeBSD/arm64 EFI loader, Revision 1.1 Command line arguments: loader.efi Image base: 0x39b08000 EFI version: 2.90 EFI Firmware: Das U-Boot (rev 8226.1024) Console: efi (0x1000) Load Path: /efi\boot\bootaa64.efi Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x3)/UsbClass(0x1e91,0xa2a5,0x0,0x0,0x0)/HD(1,0x01,0,0x800,0x19000) Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x3)/UsbClass(0x1e91,0xa2a5,0x0,0x0,0x0)/HD(1,0x01,0,0x800,0x19000) Setting currdev to disk1p1: Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x3)/UsbClass(0x1e91,0xa2a5,0x0,0x0,0x0)/HD(2,0x01,0,0x19800,0x1bf0acb0) Setting currdev to disk1p2: ERROR: cannot open /boot/lua/loader.lua: no such file or directory. Type '?' for a list of commands, 'help' for more detailed help. OK lsdev disk devices: disk0: 60258304 X 512 blocks (removable) disk1: 468862128 X 512 blocks disk1s1: DOS/Windows disk1s2: FreeBSD disk1s2a: FreeBSD UFS http: (unknown) net devices: net0: OK ls / d EFI d dtb README u-boot.bin armstub8.bin armstub8-gic.bin bootcode.bin fixup_cd.dat fixup_db.dat fixup_x.dat fixup.dat LICENCE.broadcom start_cd.elf start_db.elf start_x.elf start.elf fixup4.dat fixup4cd.dat fixup4db.dat fixup4x.dat start4.elf start4cd.elf start4db.elf start4x.elf bcm2710-rpi-2-b.dtb bcm2710-rpi-3-b.dtb bcm2710-rpi-3-b-plus.dtb bcm2711-rpi-4-b.dtb config.txt d overlays OK show COLUMNS=200 LINES=60 autoboot_delay=NO boot_serial=YES console=efi currdev=disk1s1: efi-version=2.90 efi_com_port=0 efi_com_speed=9600 hint.smbios.0.mem=0x39c2e000 interpret=OK loaddev=disk1s1: prompt=${interpret} script.lang=lua smbios.bios.reldate=04/01/2022 smbios.bios.vendor=U-Boot smbios.bios.version=2022.04 smbios.chassis.maker=Unknown smbios.chassis.type=Desktop smbios.planar.maker=Unknown smbios.planar.product=Unknown Product smbios.socket.enabled=1 smbios.system.maker=Unknown smbios.system.product=Unknown Product smbios.system.serial=100000007151395e smbios.system.uuid=30303031-3030-3030-3731-353133393565 smbios.version=3.0 twiddle_divisor=16 So definitely not working for a 2nd boot. === Mark Millard marklmi at yahoo.com