Re: RPi3 usb boot hang on stable/13
- Reply: Mark Millard : "Re: RPi3 usb boot hang on stable/13"
- Go to: [ bottom of page ] [ top of archives ] [ this month ]
Date: Sun, 03 Jul 2022 01:38:24 UTC
On 2022-Jul-2, at 15:21, bob prohaska <fbsd@www.zefox.net> wrote: > On Sat, Jul 02, 2022 at 12:00:02PM -0700, Mark Millard wrote: >> On 2022-Jul-2, at 10:34, Mark Millard <marklmi@yahoo.com> wrote: >>>> >>>> Device 0: >>> >>> That is U-Boot output. Looks like the output stopped before >>> the load of even the FreeBSD loader: FreeBSD is not involved >>> yet so it is not a FreeBSD problem. >> >> Hmm. I looked at an old RPI3 boot-session log I have around and >> it shows more text than you report. Is your serial connection >> having problems? An example that is missing is the line >> "U-Boot . . ." that identifies the version and build time >> of U-Boot. That is rather generic material to be missing. >> (I did not have a microsd card present. Such could be an >> example of expected differences.) >> >> >> There is the difference (yours then mine): >> >> MMC: mmc@7e300000: 1 >> vs. >> MMC: mmc@7e300000: 2 >> >> I wonder it if is some sort of clue about something. >> > > It just dawned there are two u-boot instances: One on the microSD, > which I think is the "special USB boot" version, which reports > U-Boot 2019.10 (Mar 17 2020 - 22:01:14 -0700) The above is what you are using when you use the microsd card. See later. > and a second on the FAT partition of the USB disk, which reports > U-Boot 2020.10 (Apr 09 2021 - 03:55:54 +0000) You are not using the above one when you use the microsd card. You are using the above one if it gets to U-Boot without a microsd card present. > Just tried removing the microSD card and issuing shutdown -r now. > The console got to "Resetting system..." and stopped. > > Put the microSD back in and tried again from the beginning. It looks > like the machine starts from microSD and transfers control to u-boot > on the USB drive. No: See later. > The USB boot OTP was set IIRC, haven't checked lately. > Maybe it's time to reformat and start over..... > > What follows is a fairly typical startup session: > > Resetting system ... > > > Raspberry Pi Bootcode > > Found SD card, config.txt = 1, start.elf = 1, recovery.elf = 0, timeout = 0 > Read File: config.txt, 178 (bytes) > > > > > Raspberry Pi Bootcode > Read File: config.txt, 178 > Read File: start.elf, 2835780 (bytes) > Read File: fixup.dat, 6639 (bytes) > MESS:00:00:01.108743:0: brfs: File read: /mfs/sd/config.txt /mfs/sd/ is the microsd card in your context. The above is config.txt being loaded from the microsd card. > MESS:00:00:01.112989:0: brfs: File read: 178 bytes > MESS:00:00:01.126707:0: HDMI:EDID error reading EDID block 0 attempt 0 > MESS:00:00:01.132784:0: HDMI:EDID error reading EDID block 0 attempt 1 > MESS:00:00:01.139029:0: HDMI:EDID error reading EDID block 0 attempt 2 > MESS:00:00:01.145279:0: HDMI:EDID error reading EDID block 0 attempt 3 > MESS:00:00:01.151529:0: HDMI:EDID error reading EDID block 0 attempt 4 > MESS:00:00:01.157779:0: HDMI:EDID error reading EDID block 0 attempt 5 > MESS:00:00:01.164029:0: HDMI:EDID error reading EDID block 0 attempt 6 > MESS:00:00:01.170279:0: HDMI:EDID error reading EDID block 0 attempt 7 > MESS:00:00:01.176529:0: HDMI:EDID error reading EDID block 0 attempt 8 > MESS:00:00:01.182779:0: HDMI:EDID error reading EDID block 0 attempt 9 > MESS:00:00:01.188792:0: HDMI:EDID giving up on reading EDID block 0 > MESS:00:00:01.206550:0: brfs: File read: /mfs/sd/config.txt The above is config.txt (again!) being loaded from the microsd card. > MESS:00:00:01.210671:0: HDMI:Setting property pixel encoding to Default > MESS:00:00:01.216761:0: HDMI:Setting property pixel clock type to PAL > MESS:00:00:01.222920:0: HDMI:Setting property content type flag to No data > MESS:00:00:01.229520:0: HDMI:Setting property fuzzy format match to enabled > MESS:00:00:01.236297:0: gpioman: gpioman_get_pin_num: pin LEDS_PWR_OK not defined > MESS:00:00:01.439246:0: gpioman: gpioman_get_pin_num: pin LEDS_PWR_OK not defined > MESS:00:00:01.445328:0: hdmi: HDMI:hdmi_get_state is deprecated, use hdmi_get_display_state instead > MESS:00:00:01.453811:0: hdmi: HDMI:>>>>>>>>>>>>>Rx sensed, reading EDID<<<<<<<<<<<<< > MESS:00:00:01.461557:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 0 > MESS:00:00:01.469289:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 1 > MESS:00:00:01.476056:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 2 > MESS:00:00:01.482826:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 3 > MESS:00:00:01.489597:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 4 > MESS:00:00:01.496368:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 5 > MESS:00:00:01.503138:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 6 > MESS:00:00:01.509910:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 7 > MESS:00:00:01.516681:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 8 > MESS:00:00:01.523451:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 9 > MESS:00:00:01.529985:0: hdmi: HDMI:EDID giving up on reading EDID block 0 > MESS:00:00:01.535499:0: hdmi: HDMI: No lookup table for resolution group 0 > MESS:00:00:01.542084:0: hdmi: HDMI: hotplug attached with DVI support > MESS:00:00:01.548262:0: hdmi: HDMI:hdmi_get_state is deprecated, use hdmi_get_display_state instead > MESS:00:00:01.557298:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 0 > MESS:00:00:01.565030:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 1 > MESS:00:00:01.571802:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 2 > MESS:00:00:01.578573:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 3 > MESS:00:00:01.585343:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 4 > MESS:00:00:01.592115:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 5 > MESS:00:00:01.598886:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 6 > MESS:00:00:01.605656:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 7 > MESS:00:00:01.612427:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 8 > MESS:00:00:01.619198:0: hdmi: HDMI:EDID error reading EDID block 0 attempt 9 > MESS:00:00:01.625732:0: hdmi: HDMI:EDID giving up on reading EDID block 0 > MESS:00:00:01.631505:0: hdmi: HDMI: hotplug deassert > MESS:00:00:01.635919:0: hdmi: HDMI: HDMI is currently off > MESS:00:00:01.641039:0: hdmi: HDMI: changing mode to unplugged > MESS:00:00:01.646605:0: hdmi: HDMI:hdmi_get_state is deprecated, use hdmi_get_display_state instead > MESS:00:00:01.656008:0: *** Restart logging > MESS:00:00:01.659280:0: brfs: File read: 178 bytes > MESS:00:00:01.665054:0: Failed to open command line file 'cmdline.txt' > MESS:00:00:01.672773:0: brfs: File read: /mfs/sd/armstub8.bin The above is armstub8.bin being loaded from the microsd card. > MESS:00:00:01.676824:0: Loading 'armstub8.bin' to 0x0 size 0x1700 > MESS:00:00:01.682667:0: brfs: File read: 5888 bytes > MESS:00:00:01.718268:0: brfs: File read: /mfs/sd/u-boot.bin The above is u-boot.bin being loaded from the microsd card. > MESS:00:00:01.722146:0: Loading 'u-boot.bin' to 0x80000 size 0x7a2d8 > MESS:00:00:01.731830:0: No kernel trailer - assuming DT-capable > MESS:00:00:01.736078:0: brfs: File read: 500440 bytes > MESS:00:00:01.743877:0: brfs: File read: /mfs/sd/bcm2710-rpi-3-b.dtb The above is bcm2710-rpi-3-b.dtb being loaded from the microsd card. > MESS:00:00:01.748535:0: Loading 'bcm2710-rpi-3-b.dtb' to 0xfa2d8 size 0x5f12 > MESS:00:00:01.889271:0: brfs: File read: 24338 bytes > MESS:00:00:01.892986:0: brfs: File read: /mfs/sd/config.txt The above is config.txt (again!) being loaded from the microsd card. > MESS:00:00:01.897876:0: dtparam: audio=on > MESS:00:00:01.919689:0: dtparam: i2c_arm=on > MESS:00:00:01.938056:0: dtparam: spi=on > MESS:00:00:01.954303:0: brfs: File read: 178 bytes > MESS:00:00:01.959758:0: brfs: File read: /mfs/sd/overlays/mmc.dtbo The above is overlays/mmc.dtbo being loaded from the microsd card. > MESS:00:00:01.981176:0: Loaded overlay 'mmc' > MESS:00:00:02.030370:0: brfs: File read: 1099 bytes > MESS:00:00:02.034426:0: brfs: File read: /mfs/sd/overlays/pwm.dtbo The above is overlays/pwm.dtbo being loaded from the microsd card. > MESS:00:00:02.051824:0: Loaded overlay 'pwm' > MESS:00:00:02.087719:0: brfs: File read: 946 bytes > MESS:00:00:02.091725:0: brfs: File read: /mfs/sd/overlays/pi3-disable-bt.dtbo The above is overlays/pi3-disable-bt.dtbo being loaded from the microsd card. > MESS:00:00:02.115336:0: Loaded overlay 'pi3-disable-bt' > MESS:00:00:03.175615:0: gpioman: gpioman_get_pin_num: pin EMMC_ENABLE not defined > MESS:00:00:03.287931:0: Device tree loaded to 0x4000 (size 0x63cd) > MESS:00:00:03.293589:0: uart: Set PL011 baud rate to 103448.300000 Hz > MESS:00:00:03.300125:0: uart: Baud rate change done... > MESS:00:00:03.303554:0: uart: Baud rate change done... > MESS:00:00:03.309236:0: gpioman: gpioman_get_pin_num: pin SDCARD_CONTROL_POWER not defined There is missing text from U-Boot here. But the below is from the U-Boot on the microsd card. Try renaming it, copying an alternative version, and seeing what it does? Repeat . . . ? > MMC: mmc@7e300000: 1 > Loading Environment from FAT... OK > In: serial > Out: vidconsole > Err: vidconsole > Net: No ethernet found. > starting USB... > Bus usb@7e980000: scanning bus usb@7e980000 for devices... 6 USB Device(s) found > scanning usb for storage devices... 0 Storage Device(s) found > Hit any key to stop autoboot: 0 > > Device 0: unknown device > U-Boot> usb reset > resetting USB... > Bus usb@7e980000: scanning bus usb@7e980000 for devices... 6 USB Device(s) found > scanning usb for storage devices... 0 Storage Device(s) found > U-Boot> usb reset > resetting USB... > Bus usb@7e980000: scanning bus usb@7e980000 for devices... 6 USB Device(s) found > scanning usb for storage devices... 0 Storage Device(s) found > U-Boot> usb reset > resetting USB... > Bus usb@7e980000: scanning bus usb@7e980000 for devices... 6 USB Device(s) found > scanning usb for storage devices... 0 Storage Device(s) found > U-Boot> power-cycled hub > Unknown command 'power-cycled' - try 'help' > U-Boot> usb reset > resetting USB... > Bus usb@7e980000: scanning bus usb@7e980000 for devices... 6 USB Device(s) found > scanning usb for storage devices... 0 Storage Device(s) found > U-Boot> usb reset > resetting USB... > Bus usb@7e980000: scanning bus usb@7e980000 for devices... 6 USB Device(s) found > scanning usb for storage devices... 0 Storage Device(s) found > U-Boot> editenv usb_pgood_delay > edit: 3200 > U-Boot> editenv usb_pgood_delay > edit: 19000 > > [saveenv results in "saving to FAT failed"] > > U-Boot> usb reset > resetting USB... > Bus usb@7e980000: scanning bus usb@7e980000 for devices... 6 USB Device(s) found > scanning usb for storage devices... 0 Storage Device(s) found > U-Boot> > resetting USB... > Bus usb@7e980000: scanning bus usb@7e980000 for devices... 6 USB Device(s) found > scanning usb for storage devices... 1 Storage Device(s) found > U-Boot> boot > > Device 0: Vendor: SABRENT Rev: 1214 Prod: > Type: Hard Disk > Capacity: 953869.7 MB = 931.5 GB (1953525168 x 512) > ... is now current device > Scanning usb 0:1... > Found EFI removable media binary efi/boot/bootaa64.efi The path is not explicit enough to directly indicate the microsd card vs. the USB drive. But the above is one of the (possibly) 2 FreeBSD loaders you have in your environment. > libfdt fdt_check_header(): FDT_ERR_BADMAGIC > Scanning disk mmc@7e300000.blk... > Scanning disk usb_mass_storage.lun0... > Found 5 disks > BootOrder not defined > EFI boot manager: Cannot load any image > 1259212 bytes read in 676 ms (1.8 MiB/s) > libfdt fdt_check_header(): FDT_ERR_BADMAGIC > > [whitespace omitted] The below is from one of the FreeBSD loaders. > Consoles: EFI console > Reading loader env vars from /efi/freebsd/loader.env > Setting currdev to disk1p1: > FreeBSD/arm64 EFI loader, Revision 1.1 > > Command line arguments: loader.efi > Image base: 0x39e06000 > EFI version: 2.80 > EFI Firmware: Das U-Boot (rev 8217.4096) > Console: comconsole (0) > Load Path: /efi\boot\bootaa64.efi > Load Device: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x0)/UsbClass(0x424,0x9514,0x9,0x0,0x2)/UsbClass(0x5e3,0x610,0x9,0x0,0x1)/UsbClass(0x152d,0x583,0x0,0x0,0x0)/HD(1,MBR,0x76573018,0x81f,0x18fa8) > Trying ESP: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x0)/UsbClass(0x424,0x9514,0x9,0x0,0x2)/UsbClass(0x5e3,0x610,0x9,0x0,0x1)/UsbClass(0x152d,0x583,0x0,0x0,0x0)/HD(1,MBR,0x76573018,0x81f,0x18fa8) > Setting currdev to disk1p1: > Trying: /VenHw(e61d73b9-a384-4acc-aeab-82e828f3628b)/UsbClass(0x0,0x0,0x9,0x0,0x0)/UsbClass(0x424,0x9514,0x9,0x0,0x2)/UsbClass(0x5e3,0x610,0x9,0x0,0x1)/UsbClass(0x152d,0x583,0x0,0x0,0x0)/HD(2,MBR,0x76573018,0x197c7,0x746ed5e9) > Setting currdev to disk1p2: "disk1p2:" is from the USB drive (based on the long line before it). I expect that this means that the FreeBSD loader was also from the USB drive. > Loading /boot/defaults/loader.conf > Loading /boot/defaults/loader.conf > Loading /boot/device.hints > Loading /boot/loader.conf > Loading /boot/loader.conf.local > Loading kernel... > /boot/kernel/kernel text=0x2a8 text=0x89ef40 text=0x1fb30c data=0x1a9358 data=0x0+0x2a8000 syms=[0x8+0x121740+0x8+0x1454aa] > Loading configured modules... > /boot/kernel/filemon.ko text=0x1574 text=0x272c data=0x500+0x20 syms=[0x8+0xcd8+0x8+0x7c5] > /boot/kernel/umodem.ko text=0x2160 text=0x1400 data=0x6e8+0x10 syms=[0x8+0xf48+0x8+0xb75] > loading required module 'ucom' > /boot/kernel/ucom.ko text=0x249f text=0x3360 data=0x8a0+0x858 syms=[0x8+0x1188+0x8+0xb19] > /boot/entropy size=0x1000 > /etc/hostid size=0x25 > > Hit [Enter] to boot immediately, or any other key for command prompt. > Booting [/boot/kernel/kernel]... > Using DTB provided by EFI at 0x7ef6000. > EFI framebuffer information: > addr, size 0x3eaf0000, 0x10a800 > dimensions 656 x 416 > stride 656 > masks 0x00ff0000, 0x0000ff00, 0x000000ff, 0xff000000 > ---<<BOOT>>--- This is about where the kernel output starts. > WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance The dtb files used do not have freebsd specific content. As I understand, for RPi*'s, the above is expected. > Copyright (c) 1992-2021 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD is a registered trademark of The FreeBSD Foundation. > FreeBSD 13.1-STABLE #5 stable/13-n251597-7c500f98b8d: Fri Jul 1 21:52:12 PDT 2022 > bob@pelorus.zefox.org:/usr/obj/usr/src/arm64.aarch64/sys/GENERIC arm64 > FreeBSD clang version 14.0.5 (https://github.com/llvm/llvm-project.git llvmorg-14.0.5-0-gc12386ae247c) > VT(efifb): resolution 656x416 > module firmware already present! > real memory = 993988608 (947 MB) > avail memory = 947646464 (903 MB) > Starting CPU 1 (1) > Starting CPU 2 (2) > Starting CPU 3 (3) > FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs > random: unblocking device. > random: entropy device external interface > MAP 39f42000 mode 2 pages 1 > MAP 39f4d000 mode 2 pages 1 > MAP 3b350000 mode 2 pages 16 > MAP 3f100000 mode 0 pages 1 > kbd0 at kbdmux0 > ofwbus0: <Open Firmware Device Tree> > simplebus0: <Flattened device tree simple bus> on ofwbus0 > ofw_clkbus0: <OFW clocks bus> on ofwbus0 > clk_fixed0: <Fixed clock> on ofw_clkbus0 > clk_fixed1: <Fixed clock> on ofw_clkbus0 > regfix0: <Fixed Regulator> on ofwbus0 > regfix1: <Fixed Regulator> on ofwbus0 > bcm2835_firmware0: <BCM2835 Firmware> on simplebus0 > psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 > lintc0: <BCM2836 Interrupt Controller> mem 0x40000000-0x400000ff on simplebus0 > intc0: <BCM2835 Interrupt Controller> mem 0x7e00b200-0x7e00b3ff irq 20 on simplebus0 > gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 22,23 on simplebus0 > gpiobus0: <OFW GPIO bus> on gpio0 > mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 21 on simplebus0 > generic_timer0: <ARMv7 Generic Timer> irq 0,1,2,3 on ofwbus0 > Timecounter "ARM MPCore Timecounter" frequency 19200000 Hz quality 1000 > Event timer "ARM MPCore Eventtimer" frequency 19200000 Hz quality 1000 > usb_nop_xceiv0: <USB NOP PHY> on ofwbus0 > bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007eff irq 4,5,6,7,8,9,10,11,12,13,14,15,16,17,18,19 on simplebus0 > bcmwd0: <BCM2708/2835 Watchdog> mem 0x7e100000-0x7e100027 on simplebus0 > bcm2835_clkman0: <BCM283x Clock Manager> mem 0x7e101000-0x7e102fff on simplebus0 > bcmrng0: <Broadcom BCM2835/BCM2838 RNG> mem 0x7e104000-0x7e10400f on simplebus0 > gpioc0: <GPIO controller> on gpio0 > uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e201fff irq 24 on simplebus0 > uart0: console (115200,n,8,1) > spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e204fff irq 26 on simplebus0 > spibus0: <OFW SPI bus> on spi0 > spibus0: <unknown card> at cs 0 mode 0 > spibus0: <unknown card> at cs 1 mode 0 > iichb0: <BCM2708/2835 BSC controller> mem 0x7e804000-0x7e804fff irq 37 on simplebus0 > bcm283x_dwcotg0: <DWC OTG 2.0 integrated USB controller (bcm283x)> mem 0x7e980000-0x7e98ffff,0x7e006000-0x7e006fff irq 43,44 on simplebus0 > usbus1 on bcm283x_dwcotg0 > sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 46 on simplebus0 > mmc0: <MMC/SD bus> on sdhci_bcm0 > fb0: <BCM2835 VT framebuffer driver> on simplebus0 > fb0: keeping existing fb bpp of 32 > fbd0 on fb0 > WARNING: Device "fb" is Giant locked and may be deleted before FreeBSD 14.0. > VT: Replacing driver "efifb" with new "fb". > fb0: 656x416(656x416@0,0) 32bpp > fb0: fbswap: 1, pitch 2624, base 0x3eaf0000, screen_size 1091584 > pmu0: <Performance Monitoring Unit> irq 50 on simplebus0 > cpulist0: <Open Firmware CPU Group> on ofwbus0 > cpu0: <Open Firmware CPU> on cpulist0 > bcm2835_cpufreq0: <CPU Frequency Control> on cpu0 > cpu1: <Open Firmware CPU> on cpulist0 > cpu2: <Open Firmware CPU> on cpulist0 > cpu3: <Open Firmware CPU> on cpulist0 > gpioled0: <GPIO LEDs> on ofwbus0 > gpioled0: <led0> failed to map pin > gpioled0: <led1> failed to map pin > armv8crypto0: CPU lacks AES instructions > Timecounters tick every 1.000 msec > iicbus0: <OFW I2C bus> on iichb0 > iic0: <I2C generic I/O> on iicbus0 > usbus1: 480Mbps High Speed USB v2.0 > ugen1.1: <DWCOTG OTG Root HUB> at usbus1 > uhub0 on usbus1 > uhub0: <DWCOTG OTG Root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1 > mmcsd0: 32GB <SDHC SE32G 8.0 SN 29ED3EF6 MFG 09/2015 by 3 SD> at mmc0 50.0MHz/4bit/65535-block > bcm2835_cpufreq0: ARM 600MHz, Core 250MHz, SDRAM 400MHz, Turbo OFF > CPU 0: ARM Cortex-A53 r0p4 affinity: 0 > Cache Type = <64 byte D-cacheline,64 byte I-cacheline,VIPT ICache,64 byte ERG,64 byte CWG> > Instruction Set Attributes 0 = <CRC32> > Instruction Set Attributes 1 = <> > Processor Features 0 = <AdvSIMD,FP,EL3 32,EL2 32,EL1 32,EL0 32> > Processor Features 1 = <> > Memory Model Features 0 = <TGran4,TGran64,SNSMem,BigEnd,16bit ASID,1TB PA> > Trying to mount root from ufs:/dev/da0s2a [rw]... > Memory Model Features 1 = <8bit VMID> > Memory Model Features 2 = <32bit CCIDX,48bit VA> > Debug Features 0 = <DoubleLock,2 CTX BKPTs,4 Watchpoints,6 Breakpoints,PMUv3,Debugv8> > Debug Features 1 = <> > Auxiliary Features 0 = <> > Auxiliary Features 1 = <> > AArch32 Instruction Set Attributes 5 = <CRC32,SEVL> > AArch32 Media and VFP Features 0 = <FPRound,FPSqrt,FPDivide,DP VFPv3+v4,SP VFPv3+v4,AdvSIMD> > AArch32 Media and VFP Features 1 = <SIMDFMAC,FPHP DP Conv,SIMDHP SP Conv,SIMDSP,SIMDInt,SIMDLS,FPDNaN,FPFtZ> > CPU 1: ARM Cortex-A53 r0p4 affinity: 1 > CPU 2: ARM Cortex-A53 r0p4 affinity: 2 > CPU 3: ARM Cortex-A53 r0p4 affinity: 3 > Release APs...done > uhub0: 1 port with 1 removable, self powered > ugen1.2: <vendor 0x0424 product 0x9514> at usbus1 > uhub1 on uhub0 > uhub1: <vendor 0x0424 product 0x9514, class 9/0, rev 2.00/2.00, addr 2> on usbus1 > uhub1: MTT enabled > Root mount waiting for: usbus1 CAM > uhub1: 5 ports with 4 removable, self powered > ugen1.3: <vendor 0x0424 product 0xec00> at usbus1 > smsc0 on uhub1 > smsc0: <vendor 0x0424 product 0xec00, rev 2.00/2.00, addr 3> on usbus1 > smsc0: chip 0xec00, rev. 0002 > miibus0: <MII bus> on smsc0 > smscphy0: <SMC LAN8700 10/100 interface> PHY 1 on miibus0 > smscphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > ue0: <USB Ethernet> on smsc0 > ue0: Ethernet address: b8:27:eb:71:46:4e > Root mount waiting for: usbus1 CAM > ugen1.4: <GenesysLogic USB2.1 Hub> at usbus1 > uhub2 on uhub1 > uhub2: <GenesysLogic USB2.1 Hub, class 9/0, rev 2.10/6.55, addr 4> on usbus1 > uhub2: 4 ports with 4 removable, self powered > Root mount waiting for: usbus1 CAM > usb_msc_auto_quirk: UQ_MSC_NO_GETMAXLUN set for USB mass storage device JMicron SABRENT (0x152d:0x0583) > usb_msc_auto_quirk: UQ_MSC_NO_PREVENT_ALLOW set for USB mass storage device JMicron SABRENT (0x152d:0x0583) > Root mount waiting for: usbus1 CAM > ugen1.5: <JMicron SABRENT> at usbus1 > umass0 on uhub2 > umass0: <JMicron SABRENT, class 0/0, rev 2.10/12.14, addr 5> on usbus1 > umass0: SCSI over Bulk-Only; quirks = 0x8100 > umass0:0:0: Attached to scbus0 > ugen1.6: <FTDI FT232R USB UART> at usbus1 > Root mount waiting for: CAM > Root mount waiting for: CAM > Root mount waiting for: CAM > Root mount waiting for: CAM > Root mount waiting for: CAM > Root mount waiting for: CAM > Root mount waiting for: CAM > Root mount waiting for: CAM > Root mount waiting for: CAM > Root mount waiting for: CAM > Root mount waiting for: CAM > Root mount waiting for: CAM > Root mount waiting for: CAM > Root mount waiting for: CAM > da0 at umass-sim0 bus 0 scbus0 target 0 lun 0 > da0: <SABRENT 1214> Fixed Direct Access SPC-4 SCSI device > da0: Serial Number 000000000000A > da0: 40.000MB/s transfers > da0: 953869MB (1953525168 512 byte sectors) > da0: quirks=0x2<NO_6_BYTE> > Warning: no time-of-day clock registered, system time will not be set accurately > Dual Console: Serial Primary, Video Secondary > Setting hostuuid: 30303030-3030-3030-3064-626136386435. > Setting hostid: 0x5cd40a6a. > Starting file system checks: > /dev/da0s2a: FILE SYSTEM CLEAN; SKIPPING CHECKS > /dev/da0s2a: clean, 291525 free (4757 frags, 35846 blocks, 0.6% fragmentation) > /dev/da0s2d: FILE SYSTEM CLEAN; SKIPPING CHECKS > /dev/da0s2d: clean, 225584444 free (104508 frags, 28184992 blocks, 0.0% fragmentation) /dev/da0s2a vs. /dev/da0s2d ? But both seem to have worked. > Mounting local filesystems:. > ELF ldconfig path: /lib /usr/lib /usr/lib/compat /usr/local/lib /usr/local/lib/compat/pkg /usr/local/lib/compat/pkg /usr/local/lib/perl5/5.32/mach/CORE > Setting hostname: pelorus.zefox.org. > Setting up harvesting: [UMA],[FS_ATIME],SWI,INTERRUPT,NET_NG,[NET_ETHER],NET_TUN,MOUSE,KEYBOARD,ATTACH,CACHED > Feeding entropy: . > lo0: link state changed to UP > smsc0: chip 0xec00, rev. 0002 > ue0: link state changed to DOWN > ue0: link state changed to UP > Starting Network: lo0 ue0. > lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> metric 0 mtu 16384 > options=680003<RXCSUM,TXCSUM,LINKSTATE,RXCSUM_IPV6,TXCSUM_IPV6> > inet6 ::1 prefixlen 128 > inet6 fe80::1%lo0 prefixlen 64 scopeid 0x1 > inet 127.0.0.1 netmask 0xff000000 > groups: lo > nd6 options=21<PERFORMNUD,AUTO_LINKLOCAL> > ue0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500 > options=80009<RXCSUM,VLAN_MTU,LINKSTATE> > ether b8:27:eb:71:46:4e > inet 50.1.20.24 netmask 0xffffff00 broadcast 50.1.20.255 > media: Ethernet autoselect (100baseTX <full-duplex>) > status: active > nd6 options=29<PERFORMNUD,IFDISABLED,AUTO_LINKLOCAL> > Starting devd. > Autoloading module: uftdi.ko > uftdi0 on uhub1 > uftdi0: <FT232R USB UART> on usbus1 > add host 127.0.0.1: gateway lo0 fib 0: route already in table > add net default: gateway 50.1.20.1 > add host ::1: gateway lo0 fib 0: route already in table > add net fe80::: gateway ::1 > add net ff02::: gateway ::1 > add net ::ffff:0.0.0.0: gateway ::1 > add net ::0.0.0.0: gateway ::1 > Clearing /tmp (X related). > Updating /var/run/os-release done. > Creating and/or trimming log files. > Updating motd:. > Starting syslogd. > Setting date via ntp. > 2 Jul 15:05:36 ntpdate[805]: step time server 212.7.1.131 offset +1584.319871 sec > Starting powerd. > Mounting late filesystems:. > Starting sendmail. > Starting sendmail_msp_queue. > Starting cron. > Configuring vt: blanktime. > Performing sanity check on sshd configuration. > Starting sshd. > Starting background file system checks in 60 seconds. > > Sat Jul 2 15:05:44 PDT > FreeBSD/arm64 (pelorus.zefox.org) (ttyu0) > > login: === Mark Millard marklmi at yahoo.com