Re: FYI: RPi* firmware tagged 1.20210805 appears to be the last to be bootable by FreeBSD via fdt use; sequence of 2 failure modes after that
- Reply: Mark Millard : "Re: FYI: RPi* firmware tagged 1.20210805 appears to be the last to be bootable by FreeBSD via fdt use; sequence of 2 failure modes after that"
- In reply to: Mark Millard : "Re: FYI: RPi* firmware tagged 1.20210805 appears to be the last to be bootable by FreeBSD via fdt use; sequence of 2 failure modes after that"
- Go to: [ bottom of page ] [ top of archives ] [ this month ]
Date: Sun, 24 Apr 2022 12:36:56 UTC
[I may have also found what leads to the extra messages for the 2nd failure mode, an independent issue it turns out.] On 2022-Apr-24, at 04:37, Mark Millard <marklmi@yahoo.com> wrote: > [I think I found the reason for the boot crash that is > a common failure to both failure modes. The 2nd mode > has other issues I've not analyzed.] > > On 2022-Apr-23, at 23:45, Mark Millard <marklmi@yahoo.com> wrote: > >> The following is based on a microsd card with 13.1-RC4 on >> it were I'd previously substituted my U-Boot 2022.04 build >> and tested with the RPi* firmware that is in the 13.1-RC4 >> image. Here I've tried replacing the RPi* firmware and >> holding the rest constant. >> >> The boot tests are on a 8 GiByte RPi4B Rev 1.14 with the >> B0T stepping. I've not been copying over the linux kernels, >> which they also bundle with the firmware. >> >> [13.1-RC4 is just what I happened to use. I doubt anything >> here is special to 13.* or stable/13 or main [so: 14]. >> (I do not use 12.* or stable/12.)] >> >> The observed status went like . . . >> >> >> firmware-1.20210805/boot/ >> >> The RPi* release tagged 1.20210805 is the last version that >> FreeBSD booted with. (Other than booting, logging in, and >> shutting down, I've not been testing other aspects of >> operation.) >> >> From what I've read, firmware-1.20210805/boot/ should be >> recent enough to handle the Rev 1.15 related PMIC variation. >> >> [I'll note that firmware build dates need not be the same day >> as the date encoded into the tag --in fact it is usually some >> earlier day. On rare occasion it can be a lot earlier, and >> there is an example of that below.] >> >> >> After firmware-1.20210805 there are 2 major failure modes. >> Both stop at the same sort of point in the messaging --but >> there is a huge difference in the count of earlier error >> messages. It looks to me like all the issues require >> FreeBSD changes if modern RPi* firmware/dtb's are to be >> usable via fdt. > > I've noticed a difference between the working context and > the failing ones (both failure modes). > > Failing: > > spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on simplebus0 > spibus0: <OFW SPI bus> on spi0 > spibus0: <unknown card> at cs 0 mode 0 > spibus0: <unknown card> at cs 1 mode 0 > NOTE BELOW LINES MISSING HERE. > sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 24 on simplebus0 > > Working: > > spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on simplebus0 > spibus0: <OFW SPI bus> on spi0 > spibus0: <unknown card> at cs 0 mode 0 > spibus0: <unknown card> at cs 1 mode 0 > START LINES MISSING ABOVE > iichb0: <BCM2708/2835 BSC controller> mem 0x7e804000-0x7e804fff irq 26 on simplebus0 > bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007aff irq 30,31,32,33,34,35,36,37,38,39,40 on simplebus0 > bcmwd0: <BCM2708/2835 Watchdog> mem 0x7e100000-0x7e100113,0x7e00a000-0x7e00a023,0x7ec11000-0x7ec1101f on simplebus0 > bcmrng0: <Broadcom BCM2835/BCM2838 RNG> mem 0x7e104000-0x7e104027 on simplebus0 > gpioc1: <GPIO controller> on gpio1 > END LINES MISSING ABOVE > sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 73 on simplebus0 > > In particular: > > bcm_dma0: <BCM2835 DMA Controller> mem 0x7e007000-0x7e007aff irq 30,31,32,33,34,35,36,37,38,39,40 on simplebus0 > > being missing means no bcm_dma_attach and that in turn means > that the static bcm_dma_sc == NULL still. > > The panic was: panic: vm_fault failed: ffff000000862134 > > where: > > ffff000000862134 <bcm_dma_allocate+0x88> ldaxr x1, [x9] > > which is part of: > > int > bcm_dma_allocate(int req_ch) > { > struct bcm_dma_softc *sc = bcm_dma_sc; > int ch = BCM_DMA_CH_INVALID; > int i; > > if (req_ch >= BCM_DMA_CH_MAX) > return (BCM_DMA_CH_INVALID); > > /* Auto(req_ch < 0) or CH specified */ > mtx_lock(&sc->sc_mtx); > . . . > > So the likes of &sc->sc_mtx end up being a small offset > from address zero: > > x9: 20 > > Thus the panic. > > As to how bcm_dma_allocate happened without bcm_dma_attach > happening first . . . > > The working context's dtb has the ordering: > (I also show mmcnr@ and the brcm,bcm2711-dma > just for reference.) > > dma@7e007000 { > compatible = "brcm,bcm2835-dma"; > . . . > mmc@7e300000 { > compatible = "brcm,bcm2835-mmc", "brcm,bcm2835-sdhci"; > . . . > mmcnr@7e300000 { > compatible = "brcm,bcm2835-mmc", "brcm,bcm2835-sdhci"; > . . . > dma@7e007b00 { > compatible = "brcm,bcm2711-dma"; > > But the failing context's dtb has the ordering: > (I also show mmcnr@ and the brcm,bcm2711-dma > just for reference.) > > mmc@7e300000 { > compatible = "brcm,bcm2835-mmc", "brcm,bcm2835-sdhci"; > . . . > dma@7e007000 { > compatible = "brcm,bcm2835-dma"; > . . . > mmcnr@7e300000 { > compatible = "brcm,bcm2835-mmc", "brcm,bcm2835-sdhci"; > . . . > dma@7e007b00 { > compatible = "brcm,bcm2711-dma"; > > So, for sequential handling in the failing case, the dma@7e007000 > would use bcm_dma_allocate before the bcm_dma_probe/bcm_dma_attach > sequence had happened, leading to the crash. > > Note: I used "fdt print /" from U-Boot to get the dtb and its > ordering. This was based on the address that the RPi* firmware > reports when debugging output is enabled (0x4000 here). > > >> The 1st mode happens for (I've added the -fails notation): >> >> firmware-1.20210831-fails/boot/ >> firmware-1.20210928-fails/boot/ >> firmware-1.20211007-fails/boot/ >> firmware-1.20211029-fails/boot/ >> firmware-1.20211118-fails/boot/ >> firmware-1.20220308_buster-fails/boot/ >> (The _buster one has firmware from 2021-Dec-01, which >> is before all the tagged releases listed below. >> It looks like the switch to the new major kernel >> version after buster came with other changes that >> FreeBSD has not tracked.) >> >> >> The 2nd mode happens for the following. (Again with extra >> notation.) There are a lot more error messages before the >> panic happens for these. The firmware builds for these >> are more recent than for the above list. >> >> >> firmware-1.20220118-fails/boot/ >> >> firmware-1.20220120-fails/boot/ >> firmware-1.20220308-fails-non-kernels-same-as-1.20220120/boot/ >> (I did not repeat the testing of the unchanged firmware. >> I just did the "diff -r" to discover the lack of change.) >> >> firmware-1.20220328-fails/boot/ >> firmware-1.20220331-fails-non-kernels-same-as-firmware-1.20220328-but-for-bcm2711-dtb-files/boot/ >> (Since the .dtb for the RPi4B was different, I did test this.) It looks like the extra messages, blocks of: clk_fixed4: <Fixed clock> disabled on ofwbus0 clk_fixed4: Cannot FDT parameters. device_attach: clk_fixed4 attach returned 6 Are tied to new dtb content in 2022's dtb updates: cam1_clk { compatible = "fixed-clock"; #clock-cells = <0x00000000>; status = "disabled"; phandle = <0x000000e2>; }; . . . cam0_clk { compatible = "fixed-clock"; #clock-cells = <0x00000000>; status = "disabled"; phandle = <0x000000e4>; }; These 2 did not exist back when the 1st failure mode started. They appear to be repeatedly processed from not really being handled --leading to lots of messages. The messages may just be noise for activity that is not contributing to boot failures at all. So fixing what I called the 1st failure mode might actually fix booting for all the firmware versions after the version tagged 1.20210805 . >> The failures look like (each test shown) . . . >> >> >> firmware-1.20210831/boot/ >> >> ---<<BOOT>>--- >> WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance >> Copyright (c) 1992-2021 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64 >> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git llvmorg-13.0.0-0-gd7b669b3a303) >> VT(efifb): resolution 592x448 >> module firmware already present! >> real memory = 8442929152 (8051 MB) >> avail memory = 8210251776 (7829 MB) >> Starting CPU 1 (1) >> Starting CPU 2 (2) >> Starting CPU 3 (3) >> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs >> random: unblocking device. >> random: entropy device external interface >> MAP 39f30000 mode 2 pages 1 >> MAP 39f34000 mode 2 pages 3 >> MAP 39f38000 mode 2 pages 4 >> MAP 3b350000 mode 2 pages 16 >> MAP fe100000 mode 0 pages 1 >> kbd0 at kbdmux0 >> ofwbus0: <Open Firmware Device Tree> >> simplebus0: <Flattened device tree simple bus> on ofwbus0 >> ofw_clkbus0: <OFW clocks bus> on ofwbus0 >> clk_fixed0: <Fixed clock> on ofw_clkbus0 >> clk_fixed1: <Fixed clock> on ofw_clkbus0 >> clk_fixed2: <Fixed clock> on ofwbus0 >> clk_fixed3: <Fixed clock> on ofwbus0 >> simplebus1: <Flattened device tree simple bus> on ofwbus0 >> simplebus2: <Flattened device tree simple bus> on ofwbus0 >> regfix0: <Fixed Regulator> on ofwbus0 >> regfix1: <Fixed Regulator> on ofwbus0 >> regfix2: <Fixed Regulator> on ofwbus0 >> simplebus3: <Flattened device tree simple bus> on ofwbus0 >> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x7d5d2000-0x7d5d2eff on simplebus0 >> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0 >> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0 >> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 >> gic0: <ARM Generic Interrupt Controller> mem 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff irq 30 on simplebus0 >> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256 >> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 14,15 on simplebus0 >> gpiobus0: <OFW GPIO bus> on gpio0 >> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0 >> gpiobus1: <GPIO bus> on gpio1 >> regfix0: Cannot set GPIO pin: 6 >> REGNODE_INIT failed: 6 >> regfix0: Cannot register regulator. >> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on simplebus0 >> gpioregulator0: <GPIO controlled regulator> on ofwbus0 >> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0 >> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000 >> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000 >> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0 >> gpioc0: <GPIO controller> on gpio0 >> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on simplebus0 >> uart0: console (115200,n,8,1) >> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on simplebus0 >> spibus0: <OFW SPI bus> on spi0 >> spibus0: <unknown card> at cs 0 mode 0 >> spibus0: <unknown card> at cs 1 mode 0 >> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 24 on simplebus0 >> Fatal data abort: >> x0: ffffffff >> x1: ffff00000092b464 >> x2: 0 >> x3: 6 >> x4: ffff000000fbf77c >> x5: ffff000000fbf72c >> x6: 4000000 >> x7: 4000000 >> x8: ffff000000dfb6a0 >> x9: 20 >> x10: 0 >> x11: 1 >> x12: 300000000006e65 >> x13: fefefefeff0100 >> x14: 1d >> x15: 0 >> x16: 0 >> x17: 0 >> x18: ffff000000fbf7e0 >> x19: ffffffff >> x20: 0 >> x21: ffff000000bad000 >> x22: ffff000000bad000 >> x23: ffffa00000f8f038 >> x24: ffff00000091b612 >> x25: ffff0000008dfcfc >> x26: ffff000000943716 >> x27: ffffa00000f89a40 >> x28: 31e00000 >> x29: ffff000000fbf7e0 >> sp: ffff000000fbf7e0 >> lr: ffff0000008680a0 >> elr: ffff000000862134 >> spsr: a00000c5 >> far: 20 >> esr: 96000004 >> panic: vm_fault failed: ffff000000862134 >> cpuid = 0 >> time = 1 >> KDB: stack backtrace: >> #0 0xffff000000516268 at kdb_backtrace+0x60 >> #1 0xffff0000004c22bc at vpanic+0x174 >> #2 0xffff0000004c2144 at panic+0x44 >> #3 0xffff0000007f4928 at data_abort+0x204 >> #4 0xffff0000007d5010 at handle_el1h_sync+0x10 >> #5 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #6 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #7 0xffff000000502238 at device_attach+0x3fc >> #8 0xffff000000504324 at bus_generic_new_pass+0x120 >> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #12 0xffff000000506404 at root_bus_configure+0x40 >> #13 0xffff000000439cf8 at mi_startup+0x11c >> #14 0xffff0000000008b4 at virtdone+0x78 >> Uptime: 1s >> >> >> firmware-1.20210928/boot/ >> >> ---<<BOOT>>--- >> WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance >> Copyright (c) 1992-2021 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64 >> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git llvmorg-13.0.0-0-gd7b669b3a303) >> VT(efifb): resolution 592x448 >> module firmware already present! >> real memory = 8442929152 (8051 MB) >> avail memory = 8210251776 (7829 MB) >> Starting CPU 1 (1) >> Starting CPU 2 (2) >> Starting CPU 3 (3) >> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs >> random: unblocking device. >> random: entropy device external interface >> MAP 39f30000 mode 2 pages 1 >> MAP 39f34000 mode 2 pages 3 >> MAP 39f38000 mode 2 pages 4 >> MAP 3b350000 mode 2 pages 16 >> MAP fe100000 mode 0 pages 1 >> kbd0 at kbdmux0 >> ofwbus0: <Open Firmware Device Tree> >> simplebus0: <Flattened device tree simple bus> on ofwbus0 >> ofw_clkbus0: <OFW clocks bus> on ofwbus0 >> clk_fixed0: <Fixed clock> on ofw_clkbus0 >> clk_fixed1: <Fixed clock> on ofw_clkbus0 >> clk_fixed2: <Fixed clock> on ofwbus0 >> clk_fixed3: <Fixed clock> on ofwbus0 >> simplebus1: <Flattened device tree simple bus> on ofwbus0 >> simplebus2: <Flattened device tree simple bus> on ofwbus0 >> regfix0: <Fixed Regulator> on ofwbus0 >> regfix1: <Fixed Regulator> on ofwbus0 >> regfix2: <Fixed Regulator> on ofwbus0 >> simplebus3: <Flattened device tree simple bus> on ofwbus0 >> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x7d5d2000-0x7d5d2eff on simplebus0 >> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0 >> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0 >> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 >> gic0: <ARM Generic Interrupt Controller> mem 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff irq 30 on simplebus0 >> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256 >> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 14,15 on simplebus0 >> gpiobus0: <OFW GPIO bus> on gpio0 >> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0 >> gpiobus1: <GPIO bus> on gpio1 >> regfix0: Cannot set GPIO pin: 6 >> REGNODE_INIT failed: 6 >> regfix0: Cannot register regulator. >> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on simplebus0 >> gpioregulator0: <GPIO controlled regulator> on ofwbus0 >> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0 >> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000 >> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000 >> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0 >> gpioc0: <GPIO controller> on gpio0 >> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on simplebus0 >> uart0: console (115200,n,8,1) >> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on simplebus0 >> spibus0: <OFW SPI bus> on spi0 >> spibus0: <unknown card> at cs 0 mode 0 >> spibus0: <unknown card> at cs 1 mode 0 >> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 24 on simplebus0 >> Fatal data abort: >> x0: ffffffff >> x1: ffff00000092b464 >> x2: 0 >> x3: 6 >> x4: ffff000000fbf77c >> x5: ffff000000fbf72c >> x6: 4000000 >> x7: 4000000 >> x8: ffff000000dfb6a0 >> x9: 20 >> x10: 0 >> x11: 1 >> x12: 300000000006e65 >> x13: fefefefeff0100 >> x14: 1d >> x15: 0 >> x16: 0 >> x17: 0 >> x18: ffff000000fbf7e0 >> x19: ffffffff >> x20: 0 >> x21: ffff000000bad000 >> x22: ffff000000bad000 >> x23: ffffa00000f8f038 >> x24: ffff00000091b612 >> x25: ffff0000008dfcfc >> x26: ffff000000943716 >> x27: ffffa00000f89a40 >> x28: 31e00000 >> x29: ffff000000fbf7e0 >> sp: ffff000000fbf7e0 >> lr: ffff0000008680a0 >> elr: ffff000000862134 >> spsr: a00000c5 >> far: 20 >> esr: 96000004 >> panic: vm_fault failed: ffff000000862134 >> cpuid = 0 >> time = 1 >> KDB: stack backtrace: >> #0 0xffff000000516268 at kdb_backtrace+0x60 >> #1 0xffff0000004c22bc at vpanic+0x174 >> #2 0xffff0000004c2144 at panic+0x44 >> #3 0xffff0000007f4928 at data_abort+0x204 >> #4 0xffff0000007d5010 at handle_el1h_sync+0x10 >> #5 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #6 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #7 0xffff000000502238 at device_attach+0x3fc >> #8 0xffff000000504324 at bus_generic_new_pass+0x120 >> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #12 0xffff000000506404 at root_bus_configure+0x40 >> #13 0xffff000000439cf8 at mi_startup+0x11c >> #14 0xffff0000000008b4 at virtdone+0x78 >> Uptime: 1s >> >> >> firmware-1.20211007/boot/ >> >> ---<<BOOT>>--- >> WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance >> Copyright (c) 1992-2021 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64 >> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git llvmorg-13.0.0-0-gd7b669b3a303) >> VT(efifb): resolution 592x448 >> module firmware already present! >> real memory = 8442929152 (8051 MB) >> avail memory = 8210251776 (7829 MB) >> Starting CPU 1 (1) >> Starting CPU 2 (2) >> Starting CPU 3 (3) >> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs >> random: unblocking device. >> random: entropy device external interface >> MAP 39f30000 mode 2 pages 1 >> MAP 39f34000 mode 2 pages 3 >> MAP 39f38000 mode 2 pages 4 >> MAP 3b350000 mode 2 pages 16 >> MAP fe100000 mode 0 pages 1 >> kbd0 at kbdmux0 >> ofwbus0: <Open Firmware Device Tree> >> simplebus0: <Flattened device tree simple bus> on ofwbus0 >> ofw_clkbus0: <OFW clocks bus> on ofwbus0 >> clk_fixed0: <Fixed clock> on ofw_clkbus0 >> clk_fixed1: <Fixed clock> on ofw_clkbus0 >> clk_fixed2: <Fixed clock> on ofwbus0 >> clk_fixed3: <Fixed clock> on ofwbus0 >> simplebus1: <Flattened device tree simple bus> on ofwbus0 >> simplebus2: <Flattened device tree simple bus> on ofwbus0 >> regfix0: <Fixed Regulator> on ofwbus0 >> regfix1: <Fixed Regulator> on ofwbus0 >> regfix2: <Fixed Regulator> on ofwbus0 >> simplebus3: <Flattened device tree simple bus> on ofwbus0 >> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x7d5d2000-0x7d5d2eff on simplebus0 >> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0 >> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0 >> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 >> gic0: <ARM Generic Interrupt Controller> mem 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff irq 30 on simplebus0 >> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256 >> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 14,15 on simplebus0 >> gpiobus0: <OFW GPIO bus> on gpio0 >> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0 >> gpiobus1: <GPIO bus> on gpio1 >> regfix0: Cannot set GPIO pin: 6 >> REGNODE_INIT failed: 6 >> regfix0: Cannot register regulator. >> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on simplebus0 >> gpioregulator0: <GPIO controlled regulator> on ofwbus0 >> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0 >> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000 >> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000 >> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0 >> gpioc0: <GPIO controller> on gpio0 >> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on simplebus0 >> uart0: console (115200,n,8,1) >> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on simplebus0 >> spibus0: <OFW SPI bus> on spi0 >> spibus0: <unknown card> at cs 0 mode 0 >> spibus0: <unknown card> at cs 1 mode 0 >> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 24 on simplebus0 >> Fatal data abort: >> x0: ffffffff >> x1: ffff00000092b464 >> x2: 0 >> x3: 6 >> x4: ffff000000fbf77c >> x5: ffff000000fbf72c >> x6: 4000000 >> x7: 4000000 >> x8: ffff000000dfb6a0 >> x9: 20 >> x10: 0 >> x11: 1 >> x12: 300000000006e65 >> x13: fefefefeff0100 >> x14: 1d >> x15: 0 >> x16: 0 >> x17: 0 >> x18: ffff000000fbf7e0 >> x19: ffffffff >> x20: 0 >> x21: ffff000000bad000 >> x22: ffff000000bad000 >> x23: ffffa00000f8f038 >> x24: ffff00000091b612 >> x25: ffff0000008dfcfc >> x26: ffff000000943716 >> x27: ffffa00000f89a40 >> x28: 31e00000 >> x29: ffff000000fbf7e0 >> sp: ffff000000fbf7e0 >> lr: ffff0000008680a0 >> elr: ffff000000862134 >> spsr: a00000c5 >> far: 20 >> esr: 96000004 >> panic: vm_fault failed: ffff000000862134 >> cpuid = 0 >> time = 1 >> KDB: stack backtrace: >> #0 0xffff000000516268 at kdb_backtrace+0x60 >> #1 0xffff0000004c22bc at vpanic+0x174 >> #2 0xffff0000004c2144 at panic+0x44 >> #3 0xffff0000007f4928 at data_abort+0x204 >> #4 0xffff0000007d5010 at handle_el1h_sync+0x10 >> #5 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #6 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #7 0xffff000000502238 at device_attach+0x3fc >> #8 0xffff000000504324 at bus_generic_new_pass+0x120 >> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #12 0xffff000000506404 at root_bus_configure+0x40 >> #13 0xffff000000439cf8 at mi_startup+0x11c >> #14 0xffff0000000008b4 at virtdone+0x78 >> Uptime: 1s >> >> >> firmware-1.20211029/boot/ >> >> ---<<BOOT>>--- >> WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance >> Copyright (c) 1992-2021 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64 >> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git llvmorg-13.0.0-0-gd7b669b3a303) >> VT(efifb): resolution 592x448 >> module firmware already present! >> real memory = 8442929152 (8051 MB) >> avail memory = 8210251776 (7829 MB) >> Starting CPU 1 (1) >> Starting CPU 2 (2) >> Starting CPU 3 (3) >> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs >> random: unblocking device. >> random: entropy device external interface >> MAP 39f30000 mode 2 pages 1 >> MAP 39f34000 mode 2 pages 3 >> MAP 39f38000 mode 2 pages 4 >> MAP 3b350000 mode 2 pages 16 >> MAP fe100000 mode 0 pages 1 >> kbd0 at kbdmux0 >> ofwbus0: <Open Firmware Device Tree> >> simplebus0: <Flattened device tree simple bus> on ofwbus0 >> ofw_clkbus0: <OFW clocks bus> on ofwbus0 >> clk_fixed0: <Fixed clock> on ofw_clkbus0 >> clk_fixed1: <Fixed clock> on ofw_clkbus0 >> clk_fixed2: <Fixed clock> on ofwbus0 >> clk_fixed3: <Fixed clock> on ofwbus0 >> simplebus1: <Flattened device tree simple bus> on ofwbus0 >> simplebus2: <Flattened device tree simple bus> on ofwbus0 >> regfix0: <Fixed Regulator> on ofwbus0 >> regfix1: <Fixed Regulator> on ofwbus0 >> regfix2: <Fixed Regulator> on ofwbus0 >> simplebus3: <Flattened device tree simple bus> on ofwbus0 >> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x7d5d2000-0x7d5d2eff on simplebus0 >> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0 >> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0 >> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 >> gic0: <ARM Generic Interrupt Controller> mem 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff irq 30 on simplebus0 >> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256 >> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 14,15 on simplebus0 >> gpiobus0: <OFW GPIO bus> on gpio0 >> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0 >> gpiobus1: <GPIO bus> on gpio1 >> regfix0: Cannot set GPIO pin: 6 >> REGNODE_INIT failed: 6 >> regfix0: Cannot register regulator. >> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on simplebus0 >> gpioregulator0: <GPIO controlled regulator> on ofwbus0 >> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0 >> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000 >> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000 >> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0 >> gpioc0: <GPIO controller> on gpio0 >> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on simplebus0 >> uart0: console (115200,n,8,1) >> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on simplebus0 >> spibus0: <OFW SPI bus> on spi0 >> spibus0: <unknown card> at cs 0 mode 0 >> spibus0: <unknown card> at cs 1 mode 0 >> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 24 on simplebus0 >> Fatal data abort: >> x0: ffffffff >> x1: ffff00000092b464 >> x2: 0 >> x3: 6 >> x4: ffff000000fbf77c >> x5: ffff000000fbf72c >> x6: 4000000 >> x7: 4000000 >> x8: ffff000000dfb6a0 >> x9: 20 >> x10: 0 >> x11: 1 >> x12: 300000000006e65 >> x13: fefefefeff0100 >> x14: 1d >> x15: 0 >> x16: 0 >> x17: 0 >> x18: ffff000000fbf7e0 >> x19: ffffffff >> x20: 0 >> x21: ffff000000bad000 >> x22: ffff000000bad000 >> x23: ffffa00000f8f038 >> x24: ffff00000091b612 >> x25: ffff0000008dfcfc >> x26: ffff000000943716 >> x27: ffffa00000f89a40 >> x28: 31e00000 >> x29: ffff000000fbf7e0 >> sp: ffff000000fbf7e0 >> lr: ffff0000008680a0 >> elr: ffff000000862134 >> spsr: a00000c5 >> far: 20 >> esr: 96000004 >> panic: vm_fault failed: ffff000000862134 >> cpuid = 0 >> time = 1 >> KDB: stack backtrace: >> #0 0xffff000000516268 at kdb_backtrace+0x60 >> #1 0xffff0000004c22bc at vpanic+0x174 >> #2 0xffff0000004c2144 at panic+0x44 >> #3 0xffff0000007f4928 at data_abort+0x204 >> #4 0xffff0000007d5010 at handle_el1h_sync+0x10 >> #5 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #6 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #7 0xffff000000502238 at device_attach+0x3fc >> #8 0xffff000000504324 at bus_generic_new_pass+0x120 >> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #12 0xffff000000506404 at root_bus_configure+0x40 >> #13 0xffff000000439cf8 at mi_startup+0x11c >> #14 0xffff0000000008b4 at virtdone+0x78 >> Uptime: 1s >> >> >> firmware-1.20211118/boot/ >> >> ---<<BOOT>>--- >> WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance >> Copyright (c) 1992-2021 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64 >> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git llvmorg-13.0.0-0-gd7b669b3a303) >> VT(efifb): resolution 592x448 >> module firmware already present! >> real memory = 8442929152 (8051 MB) >> avail memory = 8210251776 (7829 MB) >> Starting CPU 1 (1) >> Starting CPU 2 (2) >> Starting CPU 3 (3) >> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs >> random: unblocking device. >> random: entropy device external interface >> MAP 39f30000 mode 2 pages 1 >> MAP 39f34000 mode 2 pages 3 >> MAP 39f38000 mode 2 pages 4 >> MAP 3b350000 mode 2 pages 16 >> MAP fe100000 mode 0 pages 1 >> kbd0 at kbdmux0 >> ofwbus0: <Open Firmware Device Tree> >> simplebus0: <Flattened device tree simple bus> on ofwbus0 >> ofw_clkbus0: <OFW clocks bus> on ofwbus0 >> clk_fixed0: <Fixed clock> on ofw_clkbus0 >> clk_fixed1: <Fixed clock> on ofw_clkbus0 >> clk_fixed2: <Fixed clock> on ofwbus0 >> clk_fixed3: <Fixed clock> on ofwbus0 >> simplebus1: <Flattened device tree simple bus> on ofwbus0 >> simplebus2: <Flattened device tree simple bus> on ofwbus0 >> regfix0: <Fixed Regulator> on ofwbus0 >> regfix1: <Fixed Regulator> on ofwbus0 >> regfix2: <Fixed Regulator> on ofwbus0 >> simplebus3: <Flattened device tree simple bus> on ofwbus0 >> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x7d5d2000-0x7d5d2eff on simplebus0 >> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0 >> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0 >> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 >> gic0: <ARM Generic Interrupt Controller> mem 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff irq 30 on simplebus0 >> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256 >> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 14,15 on simplebus0 >> gpiobus0: <OFW GPIO bus> on gpio0 >> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0 >> gpiobus1: <GPIO bus> on gpio1 >> regfix0: Cannot set GPIO pin: 6 >> REGNODE_INIT failed: 6 >> regfix0: Cannot register regulator. >> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on simplebus0 >> gpioregulator0: <GPIO controlled regulator> on ofwbus0 >> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0 >> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000 >> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000 >> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0 >> gpioc0: <GPIO controller> on gpio0 >> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on simplebus0 >> uart0: console (115200,n,8,1) >> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on simplebus0 >> spibus0: <OFW SPI bus> on spi0 >> spibus0: <unknown card> at cs 0 mode 0 >> spibus0: <unknown card> at cs 1 mode 0 >> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 24 on simplebus0 >> Fatal data abort: >> x0: ffffffff >> x1: ffff00000092b464 >> x2: 0 >> x3: 6 >> x4: ffff000000fbf77c >> x5: ffff000000fbf72c >> x6: 4000000 >> x7: 4000000 >> x8: ffff000000dfb6a0 >> x9: 20 >> x10: 0 >> x11: 1 >> x12: 300000000006e65 >> x13: fefefefeff0100 >> x14: 1d >> x15: 0 >> x16: 0 >> x17: 0 >> x18: ffff000000fbf7e0 >> x19: ffffffff >> x20: 0 >> x21: ffff000000bad000 >> x22: ffff000000bad000 >> x23: ffffa00000f8f038 >> x24: ffff00000091b612 >> x25: ffff0000008dfcfc >> x26: ffff000000943716 >> x27: ffffa00000f89a40 >> x28: 31e00000 >> x29: ffff000000fbf7e0 >> sp: ffff000000fbf7e0 >> lr: ffff0000008680a0 >> elr: ffff000000862134 >> spsr: a00000c5 >> far: 20 >> esr: 96000004 >> panic: vm_fault failed: ffff000000862134 >> cpuid = 0 >> time = 1 >> KDB: stack backtrace: >> #0 0xffff000000516268 at kdb_backtrace+0x60 >> #1 0xffff0000004c22bc at vpanic+0x174 >> #2 0xffff0000004c2144 at panic+0x44 >> #3 0xffff0000007f4928 at data_abort+0x204 >> #4 0xffff0000007d5010 at handle_el1h_sync+0x10 >> #5 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #6 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #7 0xffff000000502238 at device_attach+0x3fc >> #8 0xffff000000504324 at bus_generic_new_pass+0x120 >> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #12 0xffff000000506404 at root_bus_configure+0x40 >> #13 0xffff000000439cf8 at mi_startup+0x11c >> #14 0xffff0000000008b4 at virtdone+0x78 >> Uptime: 1s >> >> >> firmware-1.20220308_buster-fails/boot/ >> (The _buster one has firmware from 2021-Dec-01, which >> is before all the tagged releases listed below.) >> >> ---<<BOOT>>--- >> WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance >> Copyright (c) 1992-2021 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64 >> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git llvmorg-13.0.0-0-gd7b669b3a303) >> VT(efifb): resolution 592x448 >> module firmware already present! >> real memory = 8442929152 (8051 MB) >> avail memory = 8210251776 (7829 MB) >> Starting CPU 1 (1) >> Starting CPU 2 (2) >> Starting CPU 3 (3) >> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs >> random: unblocking device. >> random: entropy device external interface >> MAP 39f30000 mode 2 pages 1 >> MAP 39f34000 mode 2 pages 3 >> MAP 39f38000 mode 2 pages 4 >> MAP 3b350000 mode 2 pages 16 >> MAP fe100000 mode 0 pages 1 >> kbd0 at kbdmux0 >> ofwbus0: <Open Firmware Device Tree> >> simplebus0: <Flattened device tree simple bus> on ofwbus0 >> ofw_clkbus0: <OFW clocks bus> on ofwbus0 >> clk_fixed0: <Fixed clock> on ofw_clkbus0 >> clk_fixed1: <Fixed clock> on ofw_clkbus0 >> clk_fixed2: <Fixed clock> on ofwbus0 >> clk_fixed3: <Fixed clock> on ofwbus0 >> simplebus1: <Flattened device tree simple bus> on ofwbus0 >> simplebus2: <Flattened device tree simple bus> on ofwbus0 >> regfix0: <Fixed Regulator> on ofwbus0 >> regfix1: <Fixed Regulator> on ofwbus0 >> regfix2: <Fixed Regulator> on ofwbus0 >> simplebus3: <Flattened device tree simple bus> on ofwbus0 >> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x7d5d2000-0x7d5d2eff on simplebus0 >> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0 >> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0 >> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 >> gic0: <ARM Generic Interrupt Controller> mem 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff irq 30 on simplebus0 >> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256 >> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 14,15 on simplebus0 >> gpiobus0: <OFW GPIO bus> on gpio0 >> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0 >> gpiobus1: <GPIO bus> on gpio1 >> regfix0: Cannot set GPIO pin: 6 >> REGNODE_INIT failed: 6 >> regfix0: Cannot register regulator. >> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on simplebus0 >> gpioregulator0: <GPIO controlled regulator> on ofwbus0 >> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0 >> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000 >> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000 >> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0 >> gpioc0: <GPIO controller> on gpio0 >> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on simplebus0 >> uart0: console (115200,n,8,1) >> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on simplebus0 >> spibus0: <OFW SPI bus> on spi0 >> spibus0: <unknown card> at cs 0 mode 0 >> spibus0: <unknown card> at cs 1 mode 0 >> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 24 on simplebus0 >> Fatal data abort: >> x0: ffffffff >> x1: ffff00000092b464 >> x2: 0 >> x3: 6 >> x4: ffff000000fbf77c >> x5: ffff000000fbf72c >> x6: 4000000 >> x7: 4000000 >> x8: ffff000000dfb6a0 >> x9: 20 >> x10: 0 >> x11: 1 >> x12: 300000000006e65 >> x13: fefefefeff0100 >> x14: 1d >> x15: 0 >> x16: 0 >> x17: 0 >> x18: ffff000000fbf7e0 >> x19: ffffffff >> x20: 0 >> x21: ffff000000bad000 >> x22: ffff000000bad000 >> x23: ffffa00000f8f038 >> x24: ffff00000091b612 >> x25: ffff0000008dfcfc >> x26: ffff000000943716 >> x27: ffffa00000f89a40 >> x28: 31e00000 >> x29: ffff000000fbf7e0 >> sp: ffff000000fbf7e0 >> lr: ffff0000008680a0 >> elr: ffff000000862134 >> spsr: a00000c5 >> far: 20 >> esr: 96000004 >> panic: vm_fault failed: ffff000000862134 >> cpuid = 0 >> time = 1 >> KDB: stack backtrace: >> #0 0xffff000000516268 at kdb_backtrace+0x60 >> #1 0xffff0000004c22bc at vpanic+0x174 >> #2 0xffff0000004c2144 at panic+0x44 >> #3 0xffff0000007f4928 at data_abort+0x204 >> #4 0xffff0000007d5010 at handle_el1h_sync+0x10 >> #5 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #6 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #7 0xffff000000502238 at device_attach+0x3fc >> #8 0xffff000000504324 at bus_generic_new_pass+0x120 >> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #12 0xffff000000506404 at root_bus_configure+0x40 >> #13 0xffff000000439cf8 at mi_startup+0x11c >> #14 0xffff0000000008b4 at virtdone+0x78 >> Uptime: 1s >> >> >> >> Below are the examples of the 2nd mode of failure . . . >> >> >> firmware-1.20220118/boot/ >> >> ---<<BOOT>>--- >> WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance >> Copyright (c) 1992-2021 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64 >> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git llvmorg-13.0.0-0-gd7b669b3a303) >> VT(efifb): resolution 592x448 >> module firmware already present! >> real memory = 8442929152 (8051 MB) >> avail memory = 8210247680 (7829 MB) >> Starting CPU 1 (1) >> Starting CPU 2 (2) >> Starting CPU 3 (3) >> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs >> random: unblocking device. >> random: entropy device external interface >> MAP 39f2f000 mode 2 pages 1 >> MAP 39f33000 mode 2 pages 3 >> MAP 39f37000 mode 2 pages 4 >> MAP 3b350000 mode 2 pages 16 >> MAP fe100000 mode 0 pages 1 >> kbd0 at kbdmux0 >> ofwbus0: <Open Firmware Device Tree> >> simplebus0: <Flattened device tree simple bus> on ofwbus0 >> ofw_clkbus0: <OFW clocks bus> on ofwbus0 >> clk_fixed0: <Fixed clock> on ofw_clkbus0 >> clk_fixed1: <Fixed clock> on ofw_clkbus0 >> clk_fixed2: <Fixed clock> on ofwbus0 >> clk_fixed3: <Fixed clock> on ofwbus0 >> simplebus1: <Flattened device tree simple bus> on ofwbus0 >> simplebus2: <Flattened device tree simple bus> on ofwbus0 >> regfix0: <Fixed Regulator> on ofwbus0 >> regfix1: <Fixed Regulator> on ofwbus0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> regfix2: <Fixed Regulator> on ofwbus0 >> regfix3: <Fixed Regulator> on ofwbus0 >> regfix4: <Fixed Regulator> on ofwbus0 >> simplebus3: <Flattened device tree simple bus> on ofwbus0 >> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x7d5d2000-0x7d5d2eff on simplebus0 >> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0 >> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> gic0: <ARM Generic Interrupt Controller> mem 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff irq 30 on simplebus0 >> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 14,15 on simplebus0 >> gpiobus0: <OFW GPIO bus> on gpio0 >> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0 >> gpiobus1: <GPIO bus> on gpio1 >> regfix0: Cannot set GPIO pin: 6 >> REGNODE_INIT failed: 6 >> regfix0: Cannot register regulator. >> regfix1: Cannot configure GPIO pin: 5 >> REGNODE_INIT failed: 6 >> regfix1: Cannot register regulator. >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on simplebus0 >> gpioregulator0: <GPIO controlled regulator> on ofwbus0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0 >> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000 >> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> gpioc0: <GPIO controller> on gpio0 >> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on simplebus0 >> uart0: console (115200,n,8,1) >> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on simplebus0 >> spibus0: <OFW SPI bus> on spi0 >> spibus0: <unknown card> at cs 0 mode 0 >> spibus0: <unknown card> at cs 1 mode 0 >> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 24 on simplebus0 >> Fatal data abort: >> x0: ffffffff >> x1: ffff00000092b464 >> x2: 0 >> x3: 6 >> x4: ffff000000fbf77c >> x5: ffff000000fbf72c >> x6: 4000000 >> x7: 4000000 >> x8: ffff000000dfb6a0 >> x9: 20 >> x10: 0 >> x11: 1 >> x12: 300000000006e65 >> x13: fefefefeff0100 >> x14: 1d >> x15: 0 >> x16: 0 >> x17: 0 >> x18: ffff000000fbf7e0 >> x19: ffffffff >> x20: 0 >> x21: ffff000000bad000 >> x22: ffff000000bad000 >> x23: ffffa00000f8f038 >> x24: ffff00000091b612 >> x25: ffff0000008dfcfc >> x26: ffff000000943716 >> x27: ffffa00000f8b120 >> x28: 31e00000 >> x29: ffff000000fbf7e0 >> sp: ffff000000fbf7e0 >> lr: ffff0000008680a0 >> elr: ffff000000862134 >> spsr: a00000c5 >> far: 20 >> esr: 96000004 >> panic: vm_fault failed: ffff000000862134 >> cpuid = 0 >> time = 1 >> KDB: stack backtrace: >> #0 0xffff000000516268 at kdb_backtrace+0x60 >> #1 0xffff0000004c22bc at vpanic+0x174 >> #2 0xffff0000004c2144 at panic+0x44 >> #3 0xffff0000007f4928 at data_abort+0x204 >> #4 0xffff0000007d5010 at handle_el1h_sync+0x10 >> #5 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #6 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #7 0xffff000000502238 at device_attach+0x3fc >> #8 0xffff000000504324 at bus_generic_new_pass+0x120 >> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #12 0xffff000000506404 at root_bus_configure+0x40 >> #13 0xffff000000439cf8 at mi_startup+0x11c >> #14 0xffff0000000008b4 at virtdone+0x78 >> >> >> firmware-1.20220120/boot/ >> >> ---<<BOOT>>--- >> WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance >> Copyright (c) 1992-2021 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64 >> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git llvmorg-13.0.0-0-gd7b669b3a303) >> VT(efifb): resolution 592x448 >> module firmware already present! >> real memory = 8442929152 (8051 MB) >> avail memory = 8210247680 (7829 MB) >> Starting CPU 1 (1) >> Starting CPU 2 (2) >> Starting CPU 3 (3) >> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs >> random: unblocking device. >> random: entropy device external interface >> MAP 39f2f000 mode 2 pages 1 >> MAP 39f33000 mode 2 pages 3 >> MAP 39f37000 mode 2 pages 4 >> MAP 3b350000 mode 2 pages 16 >> MAP fe100000 mode 0 pages 1 >> kbd0 at kbdmux0 >> ofwbus0: <Open Firmware Device Tree> >> simplebus0: <Flattened device tree simple bus> on ofwbus0 >> ofw_clkbus0: <OFW clocks bus> on ofwbus0 >> clk_fixed0: <Fixed clock> on ofw_clkbus0 >> clk_fixed1: <Fixed clock> on ofw_clkbus0 >> clk_fixed2: <Fixed clock> on ofwbus0 >> clk_fixed3: <Fixed clock> on ofwbus0 >> simplebus1: <Flattened device tree simple bus> on ofwbus0 >> simplebus2: <Flattened device tree simple bus> on ofwbus0 >> regfix0: <Fixed Regulator> on ofwbus0 >> regfix1: <Fixed Regulator> on ofwbus0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> regfix2: <Fixed Regulator> on ofwbus0 >> regfix3: <Fixed Regulator> on ofwbus0 >> regfix4: <Fixed Regulator> on ofwbus0 >> simplebus3: <Flattened device tree simple bus> on ofwbus0 >> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x7d5d2000-0x7d5d2eff on simplebus0 >> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0 >> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> gic0: <ARM Generic Interrupt Controller> mem 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff irq 30 on simplebus0 >> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 14,15 on simplebus0 >> gpiobus0: <OFW GPIO bus> on gpio0 >> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0 >> gpiobus1: <GPIO bus> on gpio1 >> regfix0: Cannot set GPIO pin: 6 >> REGNODE_INIT failed: 6 >> regfix0: Cannot register regulator. >> regfix1: Cannot configure GPIO pin: 5 >> REGNODE_INIT failed: 6 >> regfix1: Cannot register regulator. >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on simplebus0 >> gpioregulator0: <GPIO controlled regulator> on ofwbus0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0 >> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000 >> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> gpioc0: <GPIO controller> on gpio0 >> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on simplebus0 >> uart0: console (115200,n,8,1) >> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on simplebus0 >> spibus0: <OFW SPI bus> on spi0 >> spibus0: <unknown card> at cs 0 mode 0 >> spibus0: <unknown card> at cs 1 mode 0 >> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 24 on simplebus0 >> Fatal data abort: >> x0: ffffffff >> x1: ffff00000092b464 >> x2: 0 >> x3: 6 >> x4: ffff000000fbf77c >> x5: ffff000000fbf72c >> x6: 4000000 >> x7: 4000000 >> x8: ffff000000dfb6a0 >> x9: 20 >> x10: 0 >> x11: 1 >> x12: 300000000006e65 >> x13: fefefefeff0100 >> x14: 1d >> x15: 0 >> x16: 0 >> x17: 0 >> x18: ffff000000fbf7e0 >> x19: ffffffff >> x20: 0 >> x21: ffff000000bad000 >> x22: ffff000000bad000 >> x23: ffffa00000f8f038 >> x24: ffff00000091b612 >> x25: ffff0000008dfcfc >> x26: ffff000000943716 >> x27: ffffa00000f8b120 >> x28: 31e00000 >> x29: ffff000000fbf7e0 >> sp: ffff000000fbf7e0 >> lr: ffff0000008680a0 >> elr: ffff000000862134 >> spsr: a00000c5 >> far: 20 >> esr: 96000004 >> panic: vm_fault failed: ffff000000862134 >> cpuid = 0 >> time = 1 >> KDB: stack backtrace: >> #0 0xffff000000516268 at kdb_backtrace+0x60 >> #1 0xffff0000004c22bc at vpanic+0x174 >> #2 0xffff0000004c2144 at panic+0x44 >> #3 0xffff0000007f4928 at data_abort+0x204 >> #4 0xffff0000007d5010 at handle_el1h_sync+0x10 >> #5 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #6 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #7 0xffff000000502238 at device_attach+0x3fc >> #8 0xffff000000504324 at bus_generic_new_pass+0x120 >> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #12 0xffff000000506404 at root_bus_configure+0x40 >> #13 0xffff000000439cf8 at mi_startup+0x11c >> #14 0xffff0000000008b4 at virtdone+0x78 >> Uptime: 1s >> >> >> firmware-1.20220328/boot/ >> >> ---<<BOOT>>--- >> WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance >> Copyright (c) 1992-2021 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64 >> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git llvmorg-13.0.0-0-gd7b669b3a303) >> VT(efifb): resolution 592x448 >> module firmware already present! >> real memory = 8442920960 (8051 MB) >> avail memory = 8210239488 (7829 MB) >> Starting CPU 1 (1) >> Starting CPU 2 (2) >> Starting CPU 3 (3) >> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs >> random: unblocking device. >> random: entropy device external interface >> MAP 39f2f000 mode 2 pages 1 >> MAP 39f33000 mode 2 pages 3 >> MAP 39f37000 mode 2 pages 4 >> MAP 3b350000 mode 2 pages 16 >> MAP fe100000 mode 0 pages 1 >> kbd0 at kbdmux0 >> ofwbus0: <Open Firmware Device Tree> >> simplebus0: <Flattened device tree simple bus> on ofwbus0 >> ofw_clkbus0: <OFW clocks bus> on ofwbus0 >> clk_fixed0: <Fixed clock> on ofw_clkbus0 >> clk_fixed1: <Fixed clock> on ofw_clkbus0 >> clk_fixed2: <Fixed clock> on ofwbus0 >> clk_fixed3: <Fixed clock> on ofwbus0 >> simplebus1: <Flattened device tree simple bus> on ofwbus0 >> simplebus2: <Flattened device tree simple bus> on ofwbus0 >> regfix0: <Fixed Regulator> on ofwbus0 >> regfix1: <Fixed Regulator> on ofwbus0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> regfix2: <Fixed Regulator> on ofwbus0 >> regfix3: <Fixed Regulator> on ofwbus0 >> regfix4: <Fixed Regulator> on ofwbus0 >> simplebus3: <Flattened device tree simple bus> on ofwbus0 >> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x7d5d2000-0x7d5d2eff on simplebus0 >> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0 >> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> gic0: <ARM Generic Interrupt Controller> mem 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff irq 30 on simplebus0 >> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 14,15 on simplebus0 >> gpiobus0: <OFW GPIO bus> on gpio0 >> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0 >> gpiobus1: <GPIO bus> on gpio1 >> regfix0: Cannot set GPIO pin: 6 >> REGNODE_INIT failed: 6 >> regfix0: Cannot register regulator. >> regfix1: Cannot configure GPIO pin: 5 >> REGNODE_INIT failed: 6 >> regfix1: Cannot register regulator. >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on simplebus0 >> gpioregulator0: <GPIO controlled regulator> on ofwbus0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0 >> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000 >> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> gpioc0: <GPIO controller> on gpio0 >> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on simplebus0 >> uart0: console (115200,n,8,1) >> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on simplebus0 >> spibus0: <OFW SPI bus> on spi0 >> spibus0: <unknown card> at cs 0 mode 0 >> spibus0: <unknown card> at cs 1 mode 0 >> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 24 on simplebus0 >> Fatal data abort: >> x0: ffffffff >> x1: ffff00000092b464 >> x2: 0 >> x3: 6 >> x4: ffff000000fbf77c >> x5: ffff000000fbf72c >> x6: 4000000 >> x7: 4000000 >> x8: ffff000000dfb6a0 >> x9: 20 >> x10: 0 >> x11: 1 >> x12: 300000000006e65 >> x13: fefefefeff0100 >> x14: 1d >> x15: 0 >> x16: 0 >> x17: 0 >> x18: ffff000000fbf7e0 >> x19: ffffffff >> x20: 0 >> x21: ffff000000bad000 >> x22: ffff000000bad000 >> x23: ffffa00000f8f038 >> x24: ffff00000091b612 >> x25: ffff0000008dfcfc >> x26: ffff000000943716 >> x27: ffffa00000f8b120 >> x28: 31e00000 >> x29: ffff000000fbf7e0 >> sp: ffff000000fbf7e0 >> lr: ffff0000008680a0 >> elr: ffff000000862134 >> spsr: a00000c5 >> far: 20 >> esr: 96000004 >> panic: vm_fault failed: ffff000000862134 >> cpuid = 0 >> time = 1 >> KDB: stack backtrace: >> #0 0xffff000000516268 at kdb_backtrace+0x60 >> #1 0xffff0000004c22bc at vpanic+0x174 >> #2 0xffff0000004c2144 at panic+0x44 >> #3 0xffff0000007f4928 at data_abort+0x204 >> #4 0xffff0000007d5010 at handle_el1h_sync+0x10 >> #5 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #6 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #7 0xffff000000502238 at device_attach+0x3fc >> #8 0xffff000000504324 at bus_generic_new_pass+0x120 >> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #12 0xffff000000506404 at root_bus_configure+0x40 >> #13 0xffff000000439cf8 at mi_startup+0x11c >> #14 0xffff0000000008b4 at virtdone+0x78 >> Uptime: 1s >> >> >> firmware-1.20220331/boot/ >> >> ---<<BOOT>>--- >> WARNING: Cannot find freebsd,dts-version property, cannot check DTB compliance >> Copyright (c) 1992-2021 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 13.1-RC4 releng/13.1-n250133-283d1b98251 GENERIC arm64 >> FreeBSD clang version 13.0.0 (git@github.com:llvm/llvm-project.git llvmorg-13.0.0-0-gd7b669b3a303) >> VT(efifb): resolution 592x448 >> module firmware already present! >> real memory = 8442920960 (8051 MB) >> avail memory = 8210239488 (7829 MB) >> Starting CPU 1 (1) >> Starting CPU 2 (2) >> Starting CPU 3 (3) >> FreeBSD/SMP: Multiprocessor System Detected: 4 CPUs >> random: unblocking device. >> random: entropy device external interface >> MAP 39f2f000 mode 2 pages 1 >> MAP 39f33000 mode 2 pages 3 >> MAP 39f37000 mode 2 pages 4 >> MAP 3b350000 mode 2 pages 16 >> MAP fe100000 mode 0 pages 1 >> kbd0 at kbdmux0 >> ofwbus0: <Open Firmware Device Tree> >> simplebus0: <Flattened device tree simple bus> on ofwbus0 >> ofw_clkbus0: <OFW clocks bus> on ofwbus0 >> clk_fixed0: <Fixed clock> on ofw_clkbus0 >> clk_fixed1: <Fixed clock> on ofw_clkbus0 >> clk_fixed2: <Fixed clock> on ofwbus0 >> clk_fixed3: <Fixed clock> on ofwbus0 >> simplebus1: <Flattened device tree simple bus> on ofwbus0 >> simplebus2: <Flattened device tree simple bus> on ofwbus0 >> regfix0: <Fixed Regulator> on ofwbus0 >> regfix1: <Fixed Regulator> on ofwbus0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> regfix2: <Fixed Regulator> on ofwbus0 >> regfix3: <Fixed Regulator> on ofwbus0 >> regfix4: <Fixed Regulator> on ofwbus0 >> simplebus3: <Flattened device tree simple bus> on ofwbus0 >> simple_mfd0: <Simple MFD (Multi-Functions Device)> mem 0x7d5d2000-0x7d5d2eff on simplebus0 >> bcm2835_firmware0: <BCM2835 Firmware> on simplebus0 >> ofw_clkbus1: <OFW clocks bus> on bcm2835_firmware0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> psci0: <ARM Power State Co-ordination Interface Driver> on ofwbus0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> gic0: <ARM Generic Interrupt Controller> mem 0x40041000-0x40041fff,0x40042000-0x40043fff,0x40044000-0x40045fff,0x40046000-0x40047fff irq 30 on simplebus0 >> gic0: pn 0x2, arch 0x2, rev 0x1, implementer 0x43b irqs 256 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> gpio0: <BCM2708/2835 GPIO controller> mem 0x7e200000-0x7e2000b3 irq 14,15 on simplebus0 >> gpiobus0: <OFW GPIO bus> on gpio0 >> gpio1: <Raspberry Pi Firmware GPIO controller> on bcm2835_firmware0 >> gpiobus1: <GPIO bus> on gpio1 >> regfix0: Cannot set GPIO pin: 6 >> REGNODE_INIT failed: 6 >> regfix0: Cannot register regulator. >> regfix1: Cannot configure GPIO pin: 5 >> REGNODE_INIT failed: 6 >> regfix1: Cannot register regulator. >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> mbox0: <BCM2835 VideoCore Mailbox> mem 0x7e00b880-0x7e00b8bf irq 13 on simplebus0 >> gpioregulator0: <GPIO controlled regulator> on ofwbus0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> generic_timer0: <ARMv8 Generic Timer> irq 4,5,6,7 on ofwbus0 >> Timecounter "ARM MPCore Timecounter" frequency 54000000 Hz quality 1000 >> Event timer "ARM MPCore Eventtimer" frequency 54000000 Hz quality 1000 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> usb_nop_xceiv0: <USB NOP PHY> on ofwbus0 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> clk_fixed4: <Fixed clock> disabled on ofwbus0 >> clk_fixed4: Cannot FDT parameters. >> device_attach: clk_fixed4 attach returned 6 >> gpioc0: <GPIO controller> on gpio0 >> uart0: <PrimeCell UART (PL011)> mem 0x7e201000-0x7e2011ff irq 16 on simplebus0 >> uart0: console (115200,n,8,1) >> spi0: <BCM2708/2835 SPI controller> mem 0x7e204000-0x7e2041ff irq 18 on simplebus0 >> spibus0: <OFW SPI bus> on spi0 >> spibus0: <unknown card> at cs 0 mode 0 >> spibus0: <unknown card> at cs 1 mode 0 >> sdhci_bcm0: <Broadcom 2708 SDHCI controller> mem 0x7e300000-0x7e3000ff irq 24 on simplebus0 >> Fatal data abort: >> x0: ffffffff >> x1: ffff00000092b464 >> x2: 0 >> x3: 6 >> x4: ffff000000fbf77c >> x5: ffff000000fbf72c >> x6: 4000000 >> x7: 4000000 >> x8: ffff000000dfb6a0 >> x9: 20 >> x10: 0 >> x11: 1 >> x12: 300000000006e65 >> x13: fefefefeff0100 >> x14: 1d >> x15: 0 >> x16: 0 >> x17: 0 >> x18: ffff000000fbf7e0 >> x19: ffffffff >> x20: 0 >> x21: ffff000000bad000 >> x22: ffff000000bad000 >> x23: ffffa00000f8f038 >> x24: ffff00000091b612 >> x25: ffff0000008dfcfc >> x26: ffff000000943716 >> x27: ffffa00000f8b120 >> x28: 31e00000 >> x29: ffff000000fbf7e0 >> sp: ffff000000fbf7e0 >> lr: ffff0000008680a0 >> elr: ffff000000862134 >> spsr: a00000c5 >> far: 20 >> esr: 96000004 >> panic: vm_fault failed: ffff000000862134 >> cpuid = 0 >> time = 1 >> KDB: stack backtrace: >> #0 0xffff000000516268 at kdb_backtrace+0x60 >> #1 0xffff0000004c22bc at vpanic+0x174 >> #2 0xffff0000004c2144 at panic+0x44 >> #3 0xffff0000007f4928 at data_abort+0x204 >> #4 0xffff0000007d5010 at handle_el1h_sync+0x10 >> #5 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #6 0xffff00000086809c at bcm_sdhci_attach+0x314 >> #7 0xffff000000502238 at device_attach+0x3fc >> #8 0xffff000000504324 at bus_generic_new_pass+0x120 >> #9 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #10 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #11 0xffff0000005042b4 at bus_generic_new_pass+0xb0 >> #12 0xffff000000506404 at root_bus_configure+0x40 >> #13 0xffff000000439cf8 at mi_startup+0x11c >> #14 0xffff0000000008b4 at virtdone+0x78 >> Uptime: 1s > === Mark Millard marklmi at yahoo.com